diff options
| author | Scott Lahteine <github@thinkyhead.com> | 2022-05-12 02:56:49 +0300 |
|---|---|---|
| committer | Scott Lahteine <github@thinkyhead.com> | 2022-05-12 07:42:40 +0300 |
| commit | bb54c9e636283724f6226b1b45aa352dc5b34e56 (patch) | |
| tree | 971541e5cf3c177bb3540fb777d9976777e0e4e8 | |
| parent | 033928436b7e9870795f73063b460ca75fb3bf03 (diff) | |
🐛 Fix dual MAX31865 init
MarlinFirmware/Marlin#23496
277 files changed, 3601 insertions, 4432 deletions
diff --git a/config/default/Configuration_adv.h b/config/default/Configuration_adv.h index 9429a01444..a78a315512 100644 --- a/config/default/Configuration_adv.h +++ b/config/default/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/3DFabXYZ/Migbot/Configuration_adv.h b/config/examples/3DFabXYZ/Migbot/Configuration_adv.h index 9ec0120640..53adebd8cc 100644 --- a/config/examples/3DFabXYZ/Migbot/Configuration_adv.h +++ b/config/examples/3DFabXYZ/Migbot/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/ADIMLab/Gantry v1/Configuration_adv.h b/config/examples/ADIMLab/Gantry v1/Configuration_adv.h index b632dedb16..af6ebe3e90 100644 --- a/config/examples/ADIMLab/Gantry v1/Configuration_adv.h +++ b/config/examples/ADIMLab/Gantry v1/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/ADIMLab/Gantry v2/Configuration_adv.h b/config/examples/ADIMLab/Gantry v2/Configuration_adv.h index f799c0625c..857d531669 100644 --- a/config/examples/ADIMLab/Gantry v2/Configuration_adv.h +++ b/config/examples/ADIMLab/Gantry v2/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Alfawise/U20-bltouch/Configuration_adv.h b/config/examples/Alfawise/U20-bltouch/Configuration_adv.h index 2234c04f11..c02c5152b1 100644 --- a/config/examples/Alfawise/U20-bltouch/Configuration_adv.h +++ b/config/examples/Alfawise/U20-bltouch/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Alfawise/U20/Configuration_adv.h b/config/examples/Alfawise/U20/Configuration_adv.h index 55f6913541..bc0363c7ef 100644 --- a/config/examples/Alfawise/U20/Configuration_adv.h +++ b/config/examples/Alfawise/U20/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/AliExpress/UM2pExt/Configuration_adv.h b/config/examples/AliExpress/UM2pExt/Configuration_adv.h index 87e422bf02..59f63d3dcc 100644 --- a/config/examples/AliExpress/UM2pExt/Configuration_adv.h +++ b/config/examples/AliExpress/UM2pExt/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Anet/A2/Configuration_adv.h b/config/examples/Anet/A2/Configuration_adv.h index ffbfc5ef9c..9f856e981f 100644 --- a/config/examples/Anet/A2/Configuration_adv.h +++ b/config/examples/Anet/A2/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Anet/A2plus/Configuration_adv.h b/config/examples/Anet/A2plus/Configuration_adv.h index ffbfc5ef9c..9f856e981f 100644 --- a/config/examples/Anet/A2plus/Configuration_adv.h +++ b/config/examples/Anet/A2plus/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Anet/A6/Configuration_adv.h b/config/examples/Anet/A6/Configuration_adv.h index 74d6ad688f..1d2dfb9b92 100644 --- a/config/examples/Anet/A6/Configuration_adv.h +++ b/config/examples/Anet/A6/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Anet/A8/Configuration_adv.h b/config/examples/Anet/A8/Configuration_adv.h index 3c46f2f51b..fb7008a0f5 100644 --- a/config/examples/Anet/A8/Configuration_adv.h +++ b/config/examples/Anet/A8/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Anet/A8plus/Configuration_adv.h b/config/examples/Anet/A8plus/Configuration_adv.h index c02288bdb6..752dbf8546 100644 --- a/config/examples/Anet/A8plus/Configuration_adv.h +++ b/config/examples/Anet/A8plus/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Anet/A9/Configuration_adv.h b/config/examples/Anet/A9/Configuration_adv.h index 518bebfeb0..958280c35f 100644 --- a/config/examples/Anet/A9/Configuration_adv.h +++ b/config/examples/Anet/A9/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Anet/E10/Configuration_adv.h b/config/examples/Anet/E10/Configuration_adv.h index 7b0f2c5ecd..bec349ad4e 100644 --- a/config/examples/Anet/E10/Configuration_adv.h +++ b/config/examples/Anet/E10/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Anet/E16/BTT SKR 1.3/Configuration_adv.h b/config/examples/Anet/E16/BTT SKR 1.3/Configuration_adv.h index 2878d57636..bd31fc3f65 100644 --- a/config/examples/Anet/E16/BTT SKR 1.3/Configuration_adv.h +++ b/config/examples/Anet/E16/BTT SKR 1.3/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Anet/E16/Stock/Configuration_adv.h b/config/examples/Anet/E16/Stock/Configuration_adv.h index c92e25881e..9050f36817 100644 --- a/config/examples/Anet/E16/Stock/Configuration_adv.h +++ b/config/examples/Anet/E16/Stock/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Anet/ET4+/Configuration_adv.h b/config/examples/Anet/ET4+/Configuration_adv.h index fd596f2b8f..4ed036b775 100644 --- a/config/examples/Anet/ET4+/Configuration_adv.h +++ b/config/examples/Anet/ET4+/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Anet/ET4-Pro/Configuration_adv.h b/config/examples/Anet/ET4-Pro/Configuration_adv.h index fd596f2b8f..4ed036b775 100644 --- a/config/examples/Anet/ET4-Pro/Configuration_adv.h +++ b/config/examples/Anet/ET4-Pro/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Anet/ET4/Configuration_adv.h b/config/examples/Anet/ET4/Configuration_adv.h index c1535056f4..cbc4d66ac6 100644 --- a/config/examples/Anet/ET4/Configuration_adv.h +++ b/config/examples/Anet/ET4/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Anet/ET4X/Configuration_adv.h b/config/examples/Anet/ET4X/Configuration_adv.h index c1535056f4..cbc4d66ac6 100644 --- a/config/examples/Anet/ET4X/Configuration_adv.h +++ b/config/examples/Anet/ET4X/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Anet/ET5-Pro/Configuration_adv.h b/config/examples/Anet/ET5-Pro/Configuration_adv.h index 5910e40539..0aebddbbad 100644 --- a/config/examples/Anet/ET5-Pro/Configuration_adv.h +++ b/config/examples/Anet/ET5-Pro/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Anet/ET5/Configuration_adv.h b/config/examples/Anet/ET5/Configuration_adv.h index 5910e40539..0aebddbbad 100644 --- a/config/examples/Anet/ET5/Configuration_adv.h +++ b/config/examples/Anet/ET5/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Anet/ET5X/Configuration_adv.h b/config/examples/Anet/ET5X/Configuration_adv.h index 5910e40539..0aebddbbad 100644 --- a/config/examples/Anet/ET5X/Configuration_adv.h +++ b/config/examples/Anet/ET5X/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/AnyCubic/Chiron/Configuration_adv.h b/config/examples/AnyCubic/Chiron/Configuration_adv.h index 656f15561d..ef778edf91 100644 --- a/config/examples/AnyCubic/Chiron/Configuration_adv.h +++ b/config/examples/AnyCubic/Chiron/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/AnyCubic/Mega Zero 2.0/Anycubic V1/Configuration_adv.h b/config/examples/AnyCubic/Mega Zero 2.0/Anycubic V1/Configuration_adv.h index 3c706fc01c..88b60bee12 100644 --- a/config/examples/AnyCubic/Mega Zero 2.0/Anycubic V1/Configuration_adv.h +++ b/config/examples/AnyCubic/Mega Zero 2.0/Anycubic V1/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/AnyCubic/Mega Zero/Anycubic V1/Configuration_adv.h b/config/examples/AnyCubic/Mega Zero/Anycubic V1/Configuration_adv.h index 331571b90e..e5facab58f 100644 --- a/config/examples/AnyCubic/Mega Zero/Anycubic V1/Configuration_adv.h +++ b/config/examples/AnyCubic/Mega Zero/Anycubic V1/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/AnyCubic/Mega Zero/BigTreeTech SKR Mini MZ V1.0/Configuration_adv.h b/config/examples/AnyCubic/Mega Zero/BigTreeTech SKR Mini MZ V1.0/Configuration_adv.h index b13fc17018..c5a313389f 100644 --- a/config/examples/AnyCubic/Mega Zero/BigTreeTech SKR Mini MZ V1.0/Configuration_adv.h +++ b/config/examples/AnyCubic/Mega Zero/BigTreeTech SKR Mini MZ V1.0/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/AnyCubic/i3 Mega/Configuration_adv.h b/config/examples/AnyCubic/i3 Mega/Configuration_adv.h index 2ff0521faf..a9839fafee 100644 --- a/config/examples/AnyCubic/i3 Mega/Configuration_adv.h +++ b/config/examples/AnyCubic/i3 Mega/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/AnyCubic/i3/Configuration_adv.h b/config/examples/AnyCubic/i3/Configuration_adv.h index 0519c73e0d..9f9f9505b4 100644 --- a/config/examples/AnyCubic/i3/Configuration_adv.h +++ b/config/examples/AnyCubic/i3/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/ArmEd/Configuration_adv.h b/config/examples/ArmEd/Configuration_adv.h index d6cd0d68d7..d7466d9e72 100644 --- a/config/examples/ArmEd/Configuration_adv.h +++ b/config/examples/ArmEd/Configuration_adv.h @@ -142,24 +142,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Artillery/Genius Pro/Configuration_adv.h b/config/examples/Artillery/Genius Pro/Configuration_adv.h index c8bd4c1135..c5decc1cd2 100644 --- a/config/examples/Artillery/Genius Pro/Configuration_adv.h +++ b/config/examples/Artillery/Genius Pro/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Artillery/Genius/BLTouch/Configuration_adv.h b/config/examples/Artillery/Genius/BLTouch/Configuration_adv.h index d047c6e4d6..dfb33e19d1 100644 --- a/config/examples/Artillery/Genius/BLTouch/Configuration_adv.h +++ b/config/examples/Artillery/Genius/BLTouch/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Artillery/Genius/V1/Configuration_adv.h b/config/examples/Artillery/Genius/V1/Configuration_adv.h index ea11a5cce0..05851ccb5a 100644 --- a/config/examples/Artillery/Genius/V1/Configuration_adv.h +++ b/config/examples/Artillery/Genius/V1/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Artillery/Hornet/Configuration_adv.h b/config/examples/Artillery/Hornet/Configuration_adv.h index adbdb0707a..573c8082f2 100644 --- a/config/examples/Artillery/Hornet/Configuration_adv.h +++ b/config/examples/Artillery/Hornet/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Artillery/Sidewinder X1/0.9 BMG - E3D V6/Configuration_adv.h b/config/examples/Artillery/Sidewinder X1/0.9 BMG - E3D V6/Configuration_adv.h index cbaf5693a5..81aaecdeaa 100644 --- a/config/examples/Artillery/Sidewinder X1/0.9 BMG - E3D V6/Configuration_adv.h +++ b/config/examples/Artillery/Sidewinder X1/0.9 BMG - E3D V6/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Artillery/Sidewinder X1/V1/Configuration_adv.h b/config/examples/Artillery/Sidewinder X1/V1/Configuration_adv.h index ea11a5cce0..05851ccb5a 100644 --- a/config/examples/Artillery/Sidewinder X1/V1/Configuration_adv.h +++ b/config/examples/Artillery/Sidewinder X1/V1/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Artillery/Sidewinder X2/Configuration_adv.h b/config/examples/Artillery/Sidewinder X2/Configuration_adv.h index 03e96fbbd3..df5829bb91 100644 --- a/config/examples/Artillery/Sidewinder X2/Configuration_adv.h +++ b/config/examples/Artillery/Sidewinder X2/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/BIBO/TouchX/cyclops/Configuration_adv.h b/config/examples/BIBO/TouchX/cyclops/Configuration_adv.h index 2061c193c7..23b035607c 100644 --- a/config/examples/BIBO/TouchX/cyclops/Configuration_adv.h +++ b/config/examples/BIBO/TouchX/cyclops/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/BIBO/TouchX/default/Configuration_adv.h b/config/examples/BIBO/TouchX/default/Configuration_adv.h index f349682ae2..e441f1f4c6 100644 --- a/config/examples/BIBO/TouchX/default/Configuration_adv.h +++ b/config/examples/BIBO/TouchX/default/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/BIQU/B1 - SKR 1.4/Configuration_adv.h b/config/examples/BIQU/B1 - SKR 1.4/Configuration_adv.h index 70dafb0d72..db7bc90b46 100644 --- a/config/examples/BIQU/B1 - SKR 1.4/Configuration_adv.h +++ b/config/examples/BIQU/B1 - SKR 1.4/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/BIQU/B1 - SKR 2/Configuration_adv.h b/config/examples/BIQU/B1 - SKR 2/Configuration_adv.h index 66f1fdeaf7..3282fd88c0 100644 --- a/config/examples/BIQU/B1 - SKR 2/Configuration_adv.h +++ b/config/examples/BIQU/B1 - SKR 2/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/BIQU/B1 SE Plus/Configuration_adv.h b/config/examples/BIQU/B1 SE Plus/Configuration_adv.h index 8e7be28fd6..b06715ce68 100644 --- a/config/examples/BIQU/B1 SE Plus/Configuration_adv.h +++ b/config/examples/BIQU/B1 SE Plus/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/BIQU/BX/Configuration_adv.h b/config/examples/BIQU/BX/Configuration_adv.h index c513148afd..29118661ea 100644 --- a/config/examples/BIQU/BX/Configuration_adv.h +++ b/config/examples/BIQU/BX/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/BIQU/Thunder Standard/Configuration_adv.h b/config/examples/BIQU/Thunder Standard/Configuration_adv.h index 42aea5fab4..9e51a6ae01 100644 --- a/config/examples/BIQU/Thunder Standard/Configuration_adv.h +++ b/config/examples/BIQU/Thunder Standard/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/BQ/Hephestos/Configuration_adv.h b/config/examples/BQ/Hephestos/Configuration_adv.h index d56befe417..eb754f42ee 100644 --- a/config/examples/BQ/Hephestos/Configuration_adv.h +++ b/config/examples/BQ/Hephestos/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/BQ/Hephestos_2/Configuration_adv.h b/config/examples/BQ/Hephestos_2/Configuration_adv.h index d8c230f008..703179c017 100644 --- a/config/examples/BQ/Hephestos_2/Configuration_adv.h +++ b/config/examples/BQ/Hephestos_2/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/BQ/WITBOX/Configuration_adv.h b/config/examples/BQ/WITBOX/Configuration_adv.h index d56befe417..eb754f42ee 100644 --- a/config/examples/BQ/WITBOX/Configuration_adv.h +++ b/config/examples/BQ/WITBOX/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/CTC/A13/Configuration_adv.h b/config/examples/CTC/A13/Configuration_adv.h index ce88f5a8fa..a2e85eaf77 100644 --- a/config/examples/CTC/A13/Configuration_adv.h +++ b/config/examples/CTC/A13/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/CTC/Bizer/Configuration_adv.h b/config/examples/CTC/Bizer/Configuration_adv.h index d1eb2ce49b..6a551dede0 100644 --- a/config/examples/CTC/Bizer/Configuration_adv.h +++ b/config/examples/CTC/Bizer/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Cartesio/Configuration_adv.h b/config/examples/Cartesio/Configuration_adv.h index 26f6f46d70..2a376f4f41 100644 --- a/config/examples/Cartesio/Configuration_adv.h +++ b/config/examples/Cartesio/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Creality/CR-10 Mini/BigTreeTech SKR Mini E3 2.0/Configuration_adv.h b/config/examples/Creality/CR-10 Mini/BigTreeTech SKR Mini E3 2.0/Configuration_adv.h index 99e83593da..dd4114e122 100644 --- a/config/examples/Creality/CR-10 Mini/BigTreeTech SKR Mini E3 2.0/Configuration_adv.h +++ b/config/examples/Creality/CR-10 Mini/BigTreeTech SKR Mini E3 2.0/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Creality/CR-10 Mini/CrealityV1/Configuration_adv.h b/config/examples/Creality/CR-10 Mini/CrealityV1/Configuration_adv.h index bbf8d9a15e..1223154264 100644 --- a/config/examples/Creality/CR-10 Mini/CrealityV1/Configuration_adv.h +++ b/config/examples/Creality/CR-10 Mini/CrealityV1/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Creality/CR-10 Mini/MEEB-3DP/Configuration_adv.h b/config/examples/Creality/CR-10 Mini/MEEB-3DP/Configuration_adv.h index 1502bfaa02..833eaf7a85 100644 --- a/config/examples/Creality/CR-10 Mini/MEEB-3DP/Configuration_adv.h +++ b/config/examples/Creality/CR-10 Mini/MEEB-3DP/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Creality/CR-10 S4/CrealityV1/Configuration_adv.h b/config/examples/Creality/CR-10 S4/CrealityV1/Configuration_adv.h index 5bb5934dc8..76de15bb16 100644 --- a/config/examples/Creality/CR-10 S4/CrealityV1/Configuration_adv.h +++ b/config/examples/Creality/CR-10 S4/CrealityV1/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Creality/CR-10 S5/BigTreeTech SKR Mini E3 1.2 with TFT35 E3 V3.0/Configuration_adv.h b/config/examples/Creality/CR-10 S5/BigTreeTech SKR Mini E3 1.2 with TFT35 E3 V3.0/Configuration_adv.h index 82bfe8417b..5f7f062c48 100644 --- a/config/examples/Creality/CR-10 S5/BigTreeTech SKR Mini E3 1.2 with TFT35 E3 V3.0/Configuration_adv.h +++ b/config/examples/Creality/CR-10 S5/BigTreeTech SKR Mini E3 1.2 with TFT35 E3 V3.0/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Creality/CR-10 S5/CrealityV1/Configuration_adv.h b/config/examples/Creality/CR-10 S5/CrealityV1/Configuration_adv.h index 5bb5934dc8..76de15bb16 100644 --- a/config/examples/Creality/CR-10 S5/CrealityV1/Configuration_adv.h +++ b/config/examples/Creality/CR-10 S5/CrealityV1/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Creality/CR-10 S5/CrealityV2.2-BLTouch/Configuration_adv.h b/config/examples/Creality/CR-10 S5/CrealityV2.2-BLTouch/Configuration_adv.h index 6d2603ccf5..630e319284 100644 --- a/config/examples/Creality/CR-10 S5/CrealityV2.2-BLTouch/Configuration_adv.h +++ b/config/examples/Creality/CR-10 S5/CrealityV2.2-BLTouch/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Creality/CR-10 V2/Configuration_adv.h b/config/examples/Creality/CR-10 V2/Configuration_adv.h index da0af01f64..30b358d5c4 100644 --- a/config/examples/Creality/CR-10 V2/Configuration_adv.h +++ b/config/examples/Creality/CR-10 V2/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Creality/CR-10 V3/Configuration_adv.h b/config/examples/Creality/CR-10 V3/Configuration_adv.h index dc780cd72c..5128517adb 100644 --- a/config/examples/Creality/CR-10 V3/Configuration_adv.h +++ b/config/examples/Creality/CR-10 V3/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Creality/CR-10/BigTreeTech SKR Mini E3 2.0/Configuration_adv.h b/config/examples/Creality/CR-10/BigTreeTech SKR Mini E3 2.0/Configuration_adv.h index a7ca3cd283..92789fca1a 100644 --- a/config/examples/Creality/CR-10/BigTreeTech SKR Mini E3 2.0/Configuration_adv.h +++ b/config/examples/Creality/CR-10/BigTreeTech SKR Mini E3 2.0/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Creality/CR-10/CrealityV1/Configuration_adv.h b/config/examples/Creality/CR-10/CrealityV1/Configuration_adv.h index cc6af1e6b2..561700babd 100644 --- a/config/examples/Creality/CR-10/CrealityV1/Configuration_adv.h +++ b/config/examples/Creality/CR-10/CrealityV1/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Creality/CR-10S/BigTreeTech SKR 1.4 Turbo TMC2209/Configuration_adv.h b/config/examples/Creality/CR-10S/BigTreeTech SKR 1.4 Turbo TMC2209/Configuration_adv.h index a78df230c8..909142a858 100644 --- a/config/examples/Creality/CR-10S/BigTreeTech SKR 1.4 Turbo TMC2209/Configuration_adv.h +++ b/config/examples/Creality/CR-10S/BigTreeTech SKR 1.4 Turbo TMC2209/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Creality/CR-10S/BigTreeTech SKR 2.0 TMC2209/Configuration_adv.h b/config/examples/Creality/CR-10S/BigTreeTech SKR 2.0 TMC2209/Configuration_adv.h index 05780fb906..ed9fd69aff 100644 --- a/config/examples/Creality/CR-10S/BigTreeTech SKR 2.0 TMC2209/Configuration_adv.h +++ b/config/examples/Creality/CR-10S/BigTreeTech SKR 2.0 TMC2209/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Creality/CR-10S/BigTreeTech SKR Mini E3 2.0/Configuration_adv.h b/config/examples/Creality/CR-10S/BigTreeTech SKR Mini E3 2.0/Configuration_adv.h index 1d6a02bfbb..e7e3e4c2a1 100644 --- a/config/examples/Creality/CR-10S/BigTreeTech SKR Mini E3 2.0/Configuration_adv.h +++ b/config/examples/Creality/CR-10S/BigTreeTech SKR Mini E3 2.0/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Creality/CR-10S/BigTreeTech SKR Pro v1.2/Configuration_adv.h b/config/examples/Creality/CR-10S/BigTreeTech SKR Pro v1.2/Configuration_adv.h index 3e708c0f37..fad1f472ac 100644 --- a/config/examples/Creality/CR-10S/BigTreeTech SKR Pro v1.2/Configuration_adv.h +++ b/config/examples/Creality/CR-10S/BigTreeTech SKR Pro v1.2/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Creality/CR-10S/CrealityV1/Configuration_adv.h b/config/examples/Creality/CR-10S/CrealityV1/Configuration_adv.h index 7260f41404..467600d4ac 100644 --- a/config/examples/Creality/CR-10S/CrealityV1/Configuration_adv.h +++ b/config/examples/Creality/CR-10S/CrealityV1/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Creality/CR-20 Pro/Configuration_adv.h b/config/examples/Creality/CR-20 Pro/Configuration_adv.h index d00ee270eb..b7dd7a8aa6 100644 --- a/config/examples/Creality/CR-20 Pro/Configuration_adv.h +++ b/config/examples/Creality/CR-20 Pro/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Creality/CR-20/Configuration_adv.h b/config/examples/Creality/CR-20/Configuration_adv.h index 80dc00601b..38562b671c 100644 --- a/config/examples/Creality/CR-20/Configuration_adv.h +++ b/config/examples/Creality/CR-20/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Creality/CR-30 PrintMill/Configuration_adv.h b/config/examples/Creality/CR-30 PrintMill/Configuration_adv.h index f75058103a..23bf3fc90d 100644 --- a/config/examples/Creality/CR-30 PrintMill/Configuration_adv.h +++ b/config/examples/Creality/CR-30 PrintMill/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Creality/CR-6 SE/Configuration_adv.h b/config/examples/Creality/CR-6 SE/Configuration_adv.h index cdd5cb836d..3116f98352 100644 --- a/config/examples/Creality/CR-6 SE/Configuration_adv.h +++ b/config/examples/Creality/CR-6 SE/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Creality/CR-8/Configuration_adv.h b/config/examples/Creality/CR-8/Configuration_adv.h index 4818c3690c..047f1a8787 100644 --- a/config/examples/Creality/CR-8/Configuration_adv.h +++ b/config/examples/Creality/CR-8/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Creality/Ender-2 Pro/CrealityV423/Configuration_adv.h b/config/examples/Creality/Ender-2 Pro/CrealityV423/Configuration_adv.h index d9ce0bd516..c826d3673d 100644 --- a/config/examples/Creality/Ender-2 Pro/CrealityV423/Configuration_adv.h +++ b/config/examples/Creality/Ender-2 Pro/CrealityV423/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Creality/Ender-2/Configuration_adv.h b/config/examples/Creality/Ender-2/Configuration_adv.h index 5745ef3711..6c9e38b201 100644 --- a/config/examples/Creality/Ender-2/Configuration_adv.h +++ b/config/examples/Creality/Ender-2/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Creality/Ender-3 Max/Configuration_adv.h b/config/examples/Creality/Ender-3 Max/Configuration_adv.h index 9874b9c0e0..0206b8c26a 100644 --- a/config/examples/Creality/Ender-3 Max/Configuration_adv.h +++ b/config/examples/Creality/Ender-3 Max/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR 1.4 Turbo/Configuration_adv.h b/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR 1.4 Turbo/Configuration_adv.h index da45b57332..1964a60983 100644 --- a/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR 1.4 Turbo/Configuration_adv.h +++ b/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR 1.4 Turbo/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 1.0/Configuration_adv.h b/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 1.0/Configuration_adv.h index e45150395f..6d13f27d9a 100644 --- a/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 1.0/Configuration_adv.h +++ b/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 1.0/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 1.2/Configuration_adv.h b/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 1.2/Configuration_adv.h index 72398b5207..13d3096e49 100644 --- a/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 1.2/Configuration_adv.h +++ b/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 1.2/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 2.0/Configuration_adv.h b/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 2.0/Configuration_adv.h index 79e950cf28..5426751252 100644 --- a/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 2.0/Configuration_adv.h +++ b/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 2.0/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 3.0/Configuration_adv.h b/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 3.0/Configuration_adv.h index 749cf5295c..1c55868bf2 100644 --- a/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 3.0/Configuration_adv.h +++ b/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 3.0/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Creality/Ender-3 Pro/CrealityV1/Configuration_adv.h b/config/examples/Creality/Ender-3 Pro/CrealityV1/Configuration_adv.h index 8dcd2639ae..8fdbf5fba3 100644 --- a/config/examples/Creality/Ender-3 Pro/CrealityV1/Configuration_adv.h +++ b/config/examples/Creality/Ender-3 Pro/CrealityV1/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Creality/Ender-3 Pro/CrealityV422/Configuration_adv.h b/config/examples/Creality/Ender-3 Pro/CrealityV422/Configuration_adv.h index 5af85dccf1..b06c1e4e92 100644 --- a/config/examples/Creality/Ender-3 Pro/CrealityV422/Configuration_adv.h +++ b/config/examples/Creality/Ender-3 Pro/CrealityV422/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Creality/Ender-3 Pro/CrealityV427/Configuration_adv.h b/config/examples/Creality/Ender-3 Pro/CrealityV427/Configuration_adv.h index b39233ab74..9b52073e5d 100644 --- a/config/examples/Creality/Ender-3 Pro/CrealityV427/Configuration_adv.h +++ b/config/examples/Creality/Ender-3 Pro/CrealityV427/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Creality/Ender-3 S1/Configuration_adv.h b/config/examples/Creality/Ender-3 S1/Configuration_adv.h index 720d7ca088..703f4284e9 100644 --- a/config/examples/Creality/Ender-3 S1/Configuration_adv.h +++ b/config/examples/Creality/Ender-3 S1/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Creality/Ender-3 V2/BigTreeTech SKR E3 Turbo/CrealityUI/Configuration_adv.h b/config/examples/Creality/Ender-3 V2/BigTreeTech SKR E3 Turbo/CrealityUI/Configuration_adv.h index b54eea226e..5d3d4cd14a 100644 --- a/config/examples/Creality/Ender-3 V2/BigTreeTech SKR E3 Turbo/CrealityUI/Configuration_adv.h +++ b/config/examples/Creality/Ender-3 V2/BigTreeTech SKR E3 Turbo/CrealityUI/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Creality/Ender-3 V2/BigTreeTech SKR E3 Turbo/MarlinUI/Configuration_adv.h b/config/examples/Creality/Ender-3 V2/BigTreeTech SKR E3 Turbo/MarlinUI/Configuration_adv.h index 9a8b006d5c..c5e0cbfb62 100644 --- a/config/examples/Creality/Ender-3 V2/BigTreeTech SKR E3 Turbo/MarlinUI/Configuration_adv.h +++ b/config/examples/Creality/Ender-3 V2/BigTreeTech SKR E3 Turbo/MarlinUI/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Creality/Ender-3 V2/BigTreeTech SKR Mini E3 v3/CrealityUI/Configuration_adv.h b/config/examples/Creality/Ender-3 V2/BigTreeTech SKR Mini E3 v3/CrealityUI/Configuration_adv.h index a0cc5acaf1..8b8a53dd75 100644 --- a/config/examples/Creality/Ender-3 V2/BigTreeTech SKR Mini E3 v3/CrealityUI/Configuration_adv.h +++ b/config/examples/Creality/Ender-3 V2/BigTreeTech SKR Mini E3 v3/CrealityUI/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Creality/Ender-3 V2/BigTreeTech SKR Mini E3 v3/MarlinUI/Configuration_adv.h b/config/examples/Creality/Ender-3 V2/BigTreeTech SKR Mini E3 v3/MarlinUI/Configuration_adv.h index 4894eebe91..65a6cc8cd7 100644 --- a/config/examples/Creality/Ender-3 V2/BigTreeTech SKR Mini E3 v3/MarlinUI/Configuration_adv.h +++ b/config/examples/Creality/Ender-3 V2/BigTreeTech SKR Mini E3 v3/MarlinUI/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Creality/Ender-3 V2/CrealityV422/CrealityUI/Configuration_adv.h b/config/examples/Creality/Ender-3 V2/CrealityV422/CrealityUI/Configuration_adv.h index 0646b39561..8f70221608 100644 --- a/config/examples/Creality/Ender-3 V2/CrealityV422/CrealityUI/Configuration_adv.h +++ b/config/examples/Creality/Ender-3 V2/CrealityV422/CrealityUI/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Creality/Ender-3 V2/CrealityV422/MarlinUI/Configuration_adv.h b/config/examples/Creality/Ender-3 V2/CrealityV422/MarlinUI/Configuration_adv.h index 6cad2316a5..85de1cc803 100644 --- a/config/examples/Creality/Ender-3 V2/CrealityV422/MarlinUI/Configuration_adv.h +++ b/config/examples/Creality/Ender-3 V2/CrealityV422/MarlinUI/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Creality/Ender-3/BigTreeTech E3 RRF/Configuration_adv.h b/config/examples/Creality/Ender-3/BigTreeTech E3 RRF/Configuration_adv.h index 9c37f46471..499cc1c2d5 100644 --- a/config/examples/Creality/Ender-3/BigTreeTech E3 RRF/Configuration_adv.h +++ b/config/examples/Creality/Ender-3/BigTreeTech E3 RRF/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Creality/Ender-3/BigTreeTech SKR 1.4/Configuration_adv.h b/config/examples/Creality/Ender-3/BigTreeTech SKR 1.4/Configuration_adv.h index 7e41497746..745912c0ce 100644 --- a/config/examples/Creality/Ender-3/BigTreeTech SKR 1.4/Configuration_adv.h +++ b/config/examples/Creality/Ender-3/BigTreeTech SKR 1.4/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Creality/Ender-3/BigTreeTech SKR E3 Turbo/2-into-1 Hotend/Configuration_adv.h b/config/examples/Creality/Ender-3/BigTreeTech SKR E3 Turbo/2-into-1 Hotend/Configuration_adv.h index 47724d06ae..9af9fffd97 100644 --- a/config/examples/Creality/Ender-3/BigTreeTech SKR E3 Turbo/2-into-1 Hotend/Configuration_adv.h +++ b/config/examples/Creality/Ender-3/BigTreeTech SKR E3 Turbo/2-into-1 Hotend/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Creality/Ender-3/BigTreeTech SKR E3 Turbo/Dual Z/Configuration_adv.h b/config/examples/Creality/Ender-3/BigTreeTech SKR E3 Turbo/Dual Z/Configuration_adv.h index bc3b5fc914..0c59c792f4 100644 --- a/config/examples/Creality/Ender-3/BigTreeTech SKR E3 Turbo/Dual Z/Configuration_adv.h +++ b/config/examples/Creality/Ender-3/BigTreeTech SKR E3 Turbo/Dual Z/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Creality/Ender-3/BigTreeTech SKR E3 Turbo/Single Extruder/Configuration_adv.h b/config/examples/Creality/Ender-3/BigTreeTech SKR E3 Turbo/Single Extruder/Configuration_adv.h index 47724d06ae..9af9fffd97 100644 --- a/config/examples/Creality/Ender-3/BigTreeTech SKR E3 Turbo/Single Extruder/Configuration_adv.h +++ b/config/examples/Creality/Ender-3/BigTreeTech SKR E3 Turbo/Single Extruder/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Creality/Ender-3/BigTreeTech SKR E3-DIP V1.1/Configuration_adv.h b/config/examples/Creality/Ender-3/BigTreeTech SKR E3-DIP V1.1/Configuration_adv.h index 9a70b65acc..1f7d0e6a6d 100644 --- a/config/examples/Creality/Ender-3/BigTreeTech SKR E3-DIP V1.1/Configuration_adv.h +++ b/config/examples/Creality/Ender-3/BigTreeTech SKR E3-DIP V1.1/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 1.0/Configuration_adv.h b/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 1.0/Configuration_adv.h index 3a7aa02c1f..ef8d1295a8 100644 --- a/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 1.0/Configuration_adv.h +++ b/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 1.0/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 1.2/Configuration_adv.h b/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 1.2/Configuration_adv.h index 2d5a9c5737..ddceb475ea 100644 --- a/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 1.2/Configuration_adv.h +++ b/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 1.2/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 2.0/Configuration_adv.h b/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 2.0/Configuration_adv.h index 8534ddc5c9..bd468b8666 100644 --- a/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 2.0/Configuration_adv.h +++ b/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 2.0/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 3.0/Configuration_adv.h b/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 3.0/Configuration_adv.h index d4718edc18..913f3dff3f 100644 --- a/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 3.0/Configuration_adv.h +++ b/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 3.0/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Creality/Ender-3/CrealityV1/Configuration_adv.h b/config/examples/Creality/Ender-3/CrealityV1/Configuration_adv.h index d08ed5b638..267f24b883 100644 --- a/config/examples/Creality/Ender-3/CrealityV1/Configuration_adv.h +++ b/config/examples/Creality/Ender-3/CrealityV1/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Creality/Ender-3/CrealityV422/Configuration_adv.h b/config/examples/Creality/Ender-3/CrealityV422/Configuration_adv.h index f2753cba74..bdf12245b6 100644 --- a/config/examples/Creality/Ender-3/CrealityV422/Configuration_adv.h +++ b/config/examples/Creality/Ender-3/CrealityV422/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Creality/Ender-3/CrealityV427/Configuration_adv.h b/config/examples/Creality/Ender-3/CrealityV427/Configuration_adv.h index 789c3d68a5..f239b66a28 100644 --- a/config/examples/Creality/Ender-3/CrealityV427/Configuration_adv.h +++ b/config/examples/Creality/Ender-3/CrealityV427/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Creality/Ender-3/FYSETC Cheetah 1.2/BLTouch/Configuration_adv.h b/config/examples/Creality/Ender-3/FYSETC Cheetah 1.2/BLTouch/Configuration_adv.h index 7a888366a1..d926cdbe99 100644 --- a/config/examples/Creality/Ender-3/FYSETC Cheetah 1.2/BLTouch/Configuration_adv.h +++ b/config/examples/Creality/Ender-3/FYSETC Cheetah 1.2/BLTouch/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Creality/Ender-3/FYSETC Cheetah 1.2/base/Configuration_adv.h b/config/examples/Creality/Ender-3/FYSETC Cheetah 1.2/base/Configuration_adv.h index 7a888366a1..d926cdbe99 100644 --- a/config/examples/Creality/Ender-3/FYSETC Cheetah 1.2/base/Configuration_adv.h +++ b/config/examples/Creality/Ender-3/FYSETC Cheetah 1.2/base/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Creality/Ender-3/FYSETC Cheetah 2.0/Configuration_adv.h b/config/examples/Creality/Ender-3/FYSETC Cheetah 2.0/Configuration_adv.h index f09ebe7d08..8ed4913b22 100644 --- a/config/examples/Creality/Ender-3/FYSETC Cheetah 2.0/Configuration_adv.h +++ b/config/examples/Creality/Ender-3/FYSETC Cheetah 2.0/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Creality/Ender-3/FYSETC Cheetah/BLTouch/Configuration_adv.h b/config/examples/Creality/Ender-3/FYSETC Cheetah/BLTouch/Configuration_adv.h index 7a888366a1..d926cdbe99 100644 --- a/config/examples/Creality/Ender-3/FYSETC Cheetah/BLTouch/Configuration_adv.h +++ b/config/examples/Creality/Ender-3/FYSETC Cheetah/BLTouch/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Creality/Ender-3/FYSETC Cheetah/base/Configuration_adv.h b/config/examples/Creality/Ender-3/FYSETC Cheetah/base/Configuration_adv.h index 7a888366a1..d926cdbe99 100644 --- a/config/examples/Creality/Ender-3/FYSETC Cheetah/base/Configuration_adv.h +++ b/config/examples/Creality/Ender-3/FYSETC Cheetah/base/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Creality/Ender-3/MEEB-3DP/Configuration_adv.h b/config/examples/Creality/Ender-3/MEEB-3DP/Configuration_adv.h index e7caded4db..8a5c9d2dea 100644 --- a/config/examples/Creality/Ender-3/MEEB-3DP/Configuration_adv.h +++ b/config/examples/Creality/Ender-3/MEEB-3DP/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Creality/Ender-3/MKS Robin E3/V1.0/Configuration_adv.h b/config/examples/Creality/Ender-3/MKS Robin E3/V1.0/Configuration_adv.h index d82f99fdcf..e79399f3c3 100644 --- a/config/examples/Creality/Ender-3/MKS Robin E3/V1.0/Configuration_adv.h +++ b/config/examples/Creality/Ender-3/MKS Robin E3/V1.0/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Creality/Ender-3/MKS Robin E3/V1.1/Configuration_adv.h b/config/examples/Creality/Ender-3/MKS Robin E3/V1.1/Configuration_adv.h index 4f564afa79..f7ed6ec981 100644 --- a/config/examples/Creality/Ender-3/MKS Robin E3/V1.1/Configuration_adv.h +++ b/config/examples/Creality/Ender-3/MKS Robin E3/V1.1/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Creality/Ender-3/MKS Robin E3P/Configuration_adv.h b/config/examples/Creality/Ender-3/MKS Robin E3P/Configuration_adv.h index fb21cc526e..a587aab42c 100644 --- a/config/examples/Creality/Ender-3/MKS Robin E3P/Configuration_adv.h +++ b/config/examples/Creality/Ender-3/MKS Robin E3P/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Creality/Ender-3/TH3D EZBoard Lite V2/Configuration_adv.h b/config/examples/Creality/Ender-3/TH3D EZBoard Lite V2/Configuration_adv.h index 5511caed91..48aafe36ee 100644 --- a/config/examples/Creality/Ender-3/TH3D EZBoard Lite V2/Configuration_adv.h +++ b/config/examples/Creality/Ender-3/TH3D EZBoard Lite V2/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Creality/Ender-4/Configuration_adv.h b/config/examples/Creality/Ender-4/Configuration_adv.h index bafbc9f58d..7ed12cb791 100644 --- a/config/examples/Creality/Ender-4/Configuration_adv.h +++ b/config/examples/Creality/Ender-4/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Creality/Ender-5 Plus/Configuration_adv.h b/config/examples/Creality/Ender-5 Plus/Configuration_adv.h index d58c45ae66..df28bd0fdc 100644 --- a/config/examples/Creality/Ender-5 Plus/Configuration_adv.h +++ b/config/examples/Creality/Ender-5 Plus/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Creality/Ender-5 Pro/BigTreeTech SKR E3 Turbo/Configuration_adv.h b/config/examples/Creality/Ender-5 Pro/BigTreeTech SKR E3 Turbo/Configuration_adv.h index f09aa76bd8..ef03f23176 100644 --- a/config/examples/Creality/Ender-5 Pro/BigTreeTech SKR E3 Turbo/Configuration_adv.h +++ b/config/examples/Creality/Ender-5 Pro/BigTreeTech SKR E3 Turbo/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Creality/Ender-5 Pro/BigTreeTech SKR Mini E3 1.2/Configuration_adv.h b/config/examples/Creality/Ender-5 Pro/BigTreeTech SKR Mini E3 1.2/Configuration_adv.h index e913618d85..078104e840 100644 --- a/config/examples/Creality/Ender-5 Pro/BigTreeTech SKR Mini E3 1.2/Configuration_adv.h +++ b/config/examples/Creality/Ender-5 Pro/BigTreeTech SKR Mini E3 1.2/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Creality/Ender-5 Pro/BigTreeTech SKR Mini E3 2.0 with BLTouch/Configuration_adv.h b/config/examples/Creality/Ender-5 Pro/BigTreeTech SKR Mini E3 2.0 with BLTouch/Configuration_adv.h index ea69be66e1..fd93038956 100644 --- a/config/examples/Creality/Ender-5 Pro/BigTreeTech SKR Mini E3 2.0 with BLTouch/Configuration_adv.h +++ b/config/examples/Creality/Ender-5 Pro/BigTreeTech SKR Mini E3 2.0 with BLTouch/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Creality/Ender-5 Pro/CrealityV1/Configuration_adv.h b/config/examples/Creality/Ender-5 Pro/CrealityV1/Configuration_adv.h index cc1321df49..3275973d40 100644 --- a/config/examples/Creality/Ender-5 Pro/CrealityV1/Configuration_adv.h +++ b/config/examples/Creality/Ender-5 Pro/CrealityV1/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Creality/Ender-5 Pro/CrealityV422/Configuration_adv.h b/config/examples/Creality/Ender-5 Pro/CrealityV422/Configuration_adv.h index 0960923db8..83f5d30318 100644 --- a/config/examples/Creality/Ender-5 Pro/CrealityV422/Configuration_adv.h +++ b/config/examples/Creality/Ender-5 Pro/CrealityV422/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Creality/Ender-5 Pro/CrealityV427/Configuration_adv.h b/config/examples/Creality/Ender-5 Pro/CrealityV427/Configuration_adv.h index c76b396313..54d4dc3120 100644 --- a/config/examples/Creality/Ender-5 Pro/CrealityV427/Configuration_adv.h +++ b/config/examples/Creality/Ender-5 Pro/CrealityV427/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Creality/Ender-5/BigTreeTech SKR E3 Turbo with BLTouch/Configuration_adv.h b/config/examples/Creality/Ender-5/BigTreeTech SKR E3 Turbo with BLTouch/Configuration_adv.h index f09aa76bd8..ef03f23176 100644 --- a/config/examples/Creality/Ender-5/BigTreeTech SKR E3 Turbo with BLTouch/Configuration_adv.h +++ b/config/examples/Creality/Ender-5/BigTreeTech SKR E3 Turbo with BLTouch/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Creality/Ender-5/BigTreeTech SKR E3 Turbo/Configuration_adv.h b/config/examples/Creality/Ender-5/BigTreeTech SKR E3 Turbo/Configuration_adv.h index 016954c37f..d848cdfc88 100644 --- a/config/examples/Creality/Ender-5/BigTreeTech SKR E3 Turbo/Configuration_adv.h +++ b/config/examples/Creality/Ender-5/BigTreeTech SKR E3 Turbo/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Creality/Ender-5/BigTreeTech SKR Mini E3 1.2/Configuration_adv.h b/config/examples/Creality/Ender-5/BigTreeTech SKR Mini E3 1.2/Configuration_adv.h index 2d5a9c5737..ddceb475ea 100644 --- a/config/examples/Creality/Ender-5/BigTreeTech SKR Mini E3 1.2/Configuration_adv.h +++ b/config/examples/Creality/Ender-5/BigTreeTech SKR Mini E3 1.2/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Creality/Ender-5/BigTreeTech SKR Mini E3 2.0/Configuration_adv.h b/config/examples/Creality/Ender-5/BigTreeTech SKR Mini E3 2.0/Configuration_adv.h index e61629ebbb..4e3a9c12f5 100644 --- a/config/examples/Creality/Ender-5/BigTreeTech SKR Mini E3 2.0/Configuration_adv.h +++ b/config/examples/Creality/Ender-5/BigTreeTech SKR Mini E3 2.0/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Creality/Ender-5/CrealityV1/Configuration_adv.h b/config/examples/Creality/Ender-5/CrealityV1/Configuration_adv.h index 6636332522..fc059ddbf9 100644 --- a/config/examples/Creality/Ender-5/CrealityV1/Configuration_adv.h +++ b/config/examples/Creality/Ender-5/CrealityV1/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Creality/Ender-5/CrealityV427/Configuration_adv.h b/config/examples/Creality/Ender-5/CrealityV427/Configuration_adv.h index 0e993025e7..cd020ef782 100644 --- a/config/examples/Creality/Ender-5/CrealityV427/Configuration_adv.h +++ b/config/examples/Creality/Ender-5/CrealityV427/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Creality/Ender-6/Configuration_adv.h b/config/examples/Creality/Ender-6/Configuration_adv.h index 3bbb69e1a0..7b0eebdc96 100644 --- a/config/examples/Creality/Ender-6/Configuration_adv.h +++ b/config/examples/Creality/Ender-6/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Dagoma/Disco Ultimate/Configuration_adv.h b/config/examples/Dagoma/Disco Ultimate/Configuration_adv.h index 38482b719a..777b54a4e5 100644 --- a/config/examples/Dagoma/Disco Ultimate/Configuration_adv.h +++ b/config/examples/Dagoma/Disco Ultimate/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Daycom/3DP-100/Configuration_adv.h b/config/examples/Daycom/3DP-100/Configuration_adv.h index e69c9e2176..44a2ee601b 100644 --- a/config/examples/Daycom/3DP-100/Configuration_adv.h +++ b/config/examples/Daycom/3DP-100/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/EXP3D/Imprimante multifonction/Configuration_adv.h b/config/examples/EXP3D/Imprimante multifonction/Configuration_adv.h index e8030c61d8..da318ddeae 100644 --- a/config/examples/EXP3D/Imprimante multifonction/Configuration_adv.h +++ b/config/examples/EXP3D/Imprimante multifonction/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/EasyThreeD/ET4000PLUS/Configuration_adv.h b/config/examples/EasyThreeD/ET4000PLUS/Configuration_adv.h index 3518e6c9d9..e58f24fe8b 100644 --- a/config/examples/EasyThreeD/ET4000PLUS/Configuration_adv.h +++ b/config/examples/EasyThreeD/ET4000PLUS/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Einstart-S/Configuration_adv.h b/config/examples/Einstart-S/Configuration_adv.h index 58e08ad413..a5a147f70b 100644 --- a/config/examples/Einstart-S/Configuration_adv.h +++ b/config/examples/Einstart-S/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Elegoo/Neptune 2/Configuration_adv.h b/config/examples/Elegoo/Neptune 2/Configuration_adv.h index 4a5bd3500c..cdec73de69 100644 --- a/config/examples/Elegoo/Neptune 2/Configuration_adv.h +++ b/config/examples/Elegoo/Neptune 2/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Eryone/Thinker SE/Configuration_adv.h b/config/examples/Eryone/Thinker SE/Configuration_adv.h index 03cd463a30..d520966421 100644 --- a/config/examples/Eryone/Thinker SE/Configuration_adv.h +++ b/config/examples/Eryone/Thinker SE/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Eryone/Thinker V2/Configuration_adv.h b/config/examples/Eryone/Thinker V2/Configuration_adv.h index 88f398df49..3370962f9e 100644 --- a/config/examples/Eryone/Thinker V2/Configuration_adv.h +++ b/config/examples/Eryone/Thinker V2/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/FYSETC/AIO_II/Configuration_adv.h b/config/examples/FYSETC/AIO_II/Configuration_adv.h index 529dd02548..59330f096b 100644 --- a/config/examples/FYSETC/AIO_II/Configuration_adv.h +++ b/config/examples/FYSETC/AIO_II/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/FYSETC/F6_13/Configuration_adv.h b/config/examples/FYSETC/F6_13/Configuration_adv.h index 0307d9b0d0..c17da8a4d2 100644 --- a/config/examples/FYSETC/F6_13/Configuration_adv.h +++ b/config/examples/FYSETC/F6_13/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/FYSETC/S6/Configuration_adv.h b/config/examples/FYSETC/S6/Configuration_adv.h index 1a9e4403cd..44f2764b99 100644 --- a/config/examples/FYSETC/S6/Configuration_adv.h +++ b/config/examples/FYSETC/S6/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Felix/DUAL/Configuration_adv.h b/config/examples/Felix/DUAL/Configuration_adv.h index 55ce0040c4..d049020e4d 100644 --- a/config/examples/Felix/DUAL/Configuration_adv.h +++ b/config/examples/Felix/DUAL/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Felix/Single/Configuration_adv.h b/config/examples/Felix/Single/Configuration_adv.h index 55ce0040c4..d049020e4d 100644 --- a/config/examples/Felix/Single/Configuration_adv.h +++ b/config/examples/Felix/Single/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/FlashForge/Creator 2X/Configuration_adv.h b/config/examples/FlashForge/Creator 2X/Configuration_adv.h index 16c423d737..741a848d92 100644 --- a/config/examples/FlashForge/Creator 2X/Configuration_adv.h +++ b/config/examples/FlashForge/Creator 2X/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/FlashForge/CreatorPro/Configuration_adv.h b/config/examples/FlashForge/CreatorPro/Configuration_adv.h index 32f43988db..78f6aa876f 100644 --- a/config/examples/FlashForge/CreatorPro/Configuration_adv.h +++ b/config/examples/FlashForge/CreatorPro/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/FlyingBear/P902/Configuration_adv.h b/config/examples/FlyingBear/P902/Configuration_adv.h index fe82f1467d..8dd59ccc52 100644 --- a/config/examples/FlyingBear/P902/Configuration_adv.h +++ b/config/examples/FlyingBear/P902/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/FlyingBear/P905H/Configuration_adv.h b/config/examples/FlyingBear/P905H/Configuration_adv.h index cbc0207cec..bd09e7af5b 100644 --- a/config/examples/FlyingBear/P905H/Configuration_adv.h +++ b/config/examples/FlyingBear/P905H/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/FolgerTech/i3-2020/Configuration_adv.h b/config/examples/FolgerTech/i3-2020/Configuration_adv.h index 8bdd2d2ffa..324b6ed827 100644 --- a/config/examples/FolgerTech/i3-2020/Configuration_adv.h +++ b/config/examples/FolgerTech/i3-2020/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Formbot/Raptor/Configuration_adv.h b/config/examples/Formbot/Raptor/Configuration_adv.h index f0eb18a7e7..11913e1f9b 100644 --- a/config/examples/Formbot/Raptor/Configuration_adv.h +++ b/config/examples/Formbot/Raptor/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Formbot/T_Rex_2+/Configuration_adv.h b/config/examples/Formbot/T_Rex_2+/Configuration_adv.h index 500344a5f4..5cdd5d3d31 100644 --- a/config/examples/Formbot/T_Rex_2+/Configuration_adv.h +++ b/config/examples/Formbot/T_Rex_2+/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Formbot/T_Rex_3/Configuration_adv.h b/config/examples/Formbot/T_Rex_3/Configuration_adv.h index c643b90f37..18698df45e 100644 --- a/config/examples/Formbot/T_Rex_3/Configuration_adv.h +++ b/config/examples/Formbot/T_Rex_3/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Geeetech/A10/Configuration_adv.h b/config/examples/Geeetech/A10/Configuration_adv.h index 996b2cd345..f7c8e755e9 100644 --- a/config/examples/Geeetech/A10/Configuration_adv.h +++ b/config/examples/Geeetech/A10/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Geeetech/A10D/Configuration_adv.h b/config/examples/Geeetech/A10D/Configuration_adv.h index b91c01608e..1c8d2f5653 100644 --- a/config/examples/Geeetech/A10D/Configuration_adv.h +++ b/config/examples/Geeetech/A10D/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Geeetech/A10M/Stock LCD/Configuration_adv.h b/config/examples/Geeetech/A10M/Stock LCD/Configuration_adv.h index 7650f1af38..64abe97b02 100644 --- a/config/examples/Geeetech/A10M/Stock LCD/Configuration_adv.h +++ b/config/examples/Geeetech/A10M/Stock LCD/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Geeetech/A10M/YHCB2004_V4.1/Configuration_adv.h b/config/examples/Geeetech/A10M/YHCB2004_V4.1/Configuration_adv.h index 7650f1af38..64abe97b02 100644 --- a/config/examples/Geeetech/A10M/YHCB2004_V4.1/Configuration_adv.h +++ b/config/examples/Geeetech/A10M/YHCB2004_V4.1/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Geeetech/A10PRO/Configuration_adv.h b/config/examples/Geeetech/A10PRO/Configuration_adv.h index 996b2cd345..f7c8e755e9 100644 --- a/config/examples/Geeetech/A10PRO/Configuration_adv.h +++ b/config/examples/Geeetech/A10PRO/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Geeetech/A10T/Stock LCD/Configuration_adv.h b/config/examples/Geeetech/A10T/Stock LCD/Configuration_adv.h index 7650f1af38..64abe97b02 100644 --- a/config/examples/Geeetech/A10T/Stock LCD/Configuration_adv.h +++ b/config/examples/Geeetech/A10T/Stock LCD/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Geeetech/A10T/YHCB2004_V4.1/Configuration_adv.h b/config/examples/Geeetech/A10T/YHCB2004_V4.1/Configuration_adv.h index 7650f1af38..64abe97b02 100644 --- a/config/examples/Geeetech/A10T/YHCB2004_V4.1/Configuration_adv.h +++ b/config/examples/Geeetech/A10T/YHCB2004_V4.1/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Geeetech/A20/Configuration_adv.h b/config/examples/Geeetech/A20/Configuration_adv.h index f4fa3bd9e5..85eb17627c 100644 --- a/config/examples/Geeetech/A20/Configuration_adv.h +++ b/config/examples/Geeetech/A20/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Geeetech/A20M/Configuration_adv.h b/config/examples/Geeetech/A20M/Configuration_adv.h index f4fa3bd9e5..85eb17627c 100644 --- a/config/examples/Geeetech/A20M/Configuration_adv.h +++ b/config/examples/Geeetech/A20M/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Geeetech/A20T/Configuration_adv.h b/config/examples/Geeetech/A20T/Configuration_adv.h index f4fa3bd9e5..85eb17627c 100644 --- a/config/examples/Geeetech/A20T/Configuration_adv.h +++ b/config/examples/Geeetech/A20T/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Geeetech/A30/Configuration_adv.h b/config/examples/Geeetech/A30/Configuration_adv.h index f6910d8b84..094fd95ff6 100644 --- a/config/examples/Geeetech/A30/Configuration_adv.h +++ b/config/examples/Geeetech/A30/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Geeetech/A30M/Configuration_adv.h b/config/examples/Geeetech/A30M/Configuration_adv.h index f6910d8b84..094fd95ff6 100644 --- a/config/examples/Geeetech/A30M/Configuration_adv.h +++ b/config/examples/Geeetech/A30M/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Geeetech/A30T/Configuration_adv.h b/config/examples/Geeetech/A30T/Configuration_adv.h index f6910d8b84..094fd95ff6 100644 --- a/config/examples/Geeetech/A30T/Configuration_adv.h +++ b/config/examples/Geeetech/A30T/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Geeetech/D200/Configuration_adv.h b/config/examples/Geeetech/D200/Configuration_adv.h index 6fc5590127..927c316124 100644 --- a/config/examples/Geeetech/D200/Configuration_adv.h +++ b/config/examples/Geeetech/D200/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Geeetech/Duplicator5/Configuration_adv.h b/config/examples/Geeetech/Duplicator5/Configuration_adv.h index 1a9e4403cd..44f2764b99 100644 --- a/config/examples/Geeetech/Duplicator5/Configuration_adv.h +++ b/config/examples/Geeetech/Duplicator5/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Geeetech/E180/Configuration_adv.h b/config/examples/Geeetech/E180/Configuration_adv.h index f6910d8b84..094fd95ff6 100644 --- a/config/examples/Geeetech/E180/Configuration_adv.h +++ b/config/examples/Geeetech/E180/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Geeetech/M201/Configuration_adv.h b/config/examples/Geeetech/M201/Configuration_adv.h index 6fc5590127..927c316124 100644 --- a/config/examples/Geeetech/M201/Configuration_adv.h +++ b/config/examples/Geeetech/M201/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Geeetech/MeCreator2/Configuration_adv.h b/config/examples/Geeetech/MeCreator2/Configuration_adv.h index 8705f15cf7..c9edeb37f4 100644 --- a/config/examples/Geeetech/MeCreator2/Configuration_adv.h +++ b/config/examples/Geeetech/MeCreator2/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Geeetech/Me_creator/Configuration_adv.h b/config/examples/Geeetech/Me_creator/Configuration_adv.h index 1a9e4403cd..44f2764b99 100644 --- a/config/examples/Geeetech/Me_creator/Configuration_adv.h +++ b/config/examples/Geeetech/Me_creator/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Geeetech/Me_ducer/Configuration_adv.h b/config/examples/Geeetech/Me_ducer/Configuration_adv.h index 95aaf1b7a7..6aefe8d007 100644 --- a/config/examples/Geeetech/Me_ducer/Configuration_adv.h +++ b/config/examples/Geeetech/Me_ducer/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Geeetech/PI3A PRO/Configuration_adv.h b/config/examples/Geeetech/PI3A PRO/Configuration_adv.h index 9d261ffa0d..04e9d31951 100644 --- a/config/examples/Geeetech/PI3A PRO/Configuration_adv.h +++ b/config/examples/Geeetech/PI3A PRO/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Geeetech/Prusa i3 Pro C/Configuration_adv.h b/config/examples/Geeetech/Prusa i3 Pro C/Configuration_adv.h index 996b2cd345..f7c8e755e9 100644 --- a/config/examples/Geeetech/Prusa i3 Pro C/Configuration_adv.h +++ b/config/examples/Geeetech/Prusa i3 Pro C/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Geeetech/Prusa i3 Pro W/Configuration_adv.h b/config/examples/Geeetech/Prusa i3 Pro W/Configuration_adv.h index 996b2cd345..f7c8e755e9 100644 --- a/config/examples/Geeetech/Prusa i3 Pro W/Configuration_adv.h +++ b/config/examples/Geeetech/Prusa i3 Pro W/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/HMS434/Configuration_adv.h b/config/examples/HMS434/Configuration_adv.h index 050529058a..b1789bd9ee 100644 --- a/config/examples/HMS434/Configuration_adv.h +++ b/config/examples/HMS434/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Index/REV_03/Configuration_adv.h b/config/examples/Index/REV_03/Configuration_adv.h index 540c7c5d4d..d3f8c1c321 100644 --- a/config/examples/Index/REV_03/Configuration_adv.h +++ b/config/examples/Index/REV_03/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Infitary/i3-M508/Configuration_adv.h b/config/examples/Infitary/i3-M508/Configuration_adv.h index 68142ce602..c44536cea8 100644 --- a/config/examples/Infitary/i3-M508/Configuration_adv.h +++ b/config/examples/Infitary/i3-M508/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Intamsys/FunmatHT 4988/Configuration_adv.h b/config/examples/Intamsys/FunmatHT 4988/Configuration_adv.h index f730489195..e0a2f6c842 100644 --- a/config/examples/Intamsys/FunmatHT 4988/Configuration_adv.h +++ b/config/examples/Intamsys/FunmatHT 4988/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/JGAurora/A1/Configuration_adv.h b/config/examples/JGAurora/A1/Configuration_adv.h index 0c84f69f54..df8cad5b2a 100644 --- a/config/examples/JGAurora/A1/Configuration_adv.h +++ b/config/examples/JGAurora/A1/Configuration_adv.h @@ -143,24 +143,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/JGAurora/A5/Configuration_adv.h b/config/examples/JGAurora/A5/Configuration_adv.h index bb3056b33d..2f2a04f16d 100644 --- a/config/examples/JGAurora/A5/Configuration_adv.h +++ b/config/examples/JGAurora/A5/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/JGAurora/A5S/Configuration_adv.h b/config/examples/JGAurora/A5S/Configuration_adv.h index 0c84f69f54..df8cad5b2a 100644 --- a/config/examples/JGAurora/A5S/Configuration_adv.h +++ b/config/examples/JGAurora/A5S/Configuration_adv.h @@ -143,24 +143,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/JGAurora/Magic/Configuration_adv.h b/config/examples/JGAurora/Magic/Configuration_adv.h index 4eb6651452..f87ce4cf0b 100644 --- a/config/examples/JGAurora/Magic/Configuration_adv.h +++ b/config/examples/JGAurora/Magic/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Kingroon/KP3/Configuration_adv.h b/config/examples/Kingroon/KP3/Configuration_adv.h index 4e54ee5e84..a0479f5883 100644 --- a/config/examples/Kingroon/KP3/Configuration_adv.h +++ b/config/examples/Kingroon/KP3/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Labists/ET4/Configuration_adv.h b/config/examples/Labists/ET4/Configuration_adv.h index fd596f2b8f..4ed036b775 100644 --- a/config/examples/Labists/ET4/Configuration_adv.h +++ b/config/examples/Labists/ET4/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/LulzBot/TAZ4/Configuration_adv.h b/config/examples/LulzBot/TAZ4/Configuration_adv.h index 029253458c..e2c17fc0c6 100644 --- a/config/examples/LulzBot/TAZ4/Configuration_adv.h +++ b/config/examples/LulzBot/TAZ4/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/MBot/Cube/Configuration_adv.h b/config/examples/MBot/Cube/Configuration_adv.h index d69a0565dd..dbe3191c2d 100644 --- a/config/examples/MBot/Cube/Configuration_adv.h +++ b/config/examples/MBot/Cube/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/MakerFarm/Pegasus 12/Configuration_adv.h b/config/examples/MakerFarm/Pegasus 12/Configuration_adv.h index 9e8e3495c4..3107191691 100644 --- a/config/examples/MakerFarm/Pegasus 12/Configuration_adv.h +++ b/config/examples/MakerFarm/Pegasus 12/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/MakerParts/Configuration_adv.h b/config/examples/MakerParts/Configuration_adv.h index 5c5c181939..f3357bf31a 100644 --- a/config/examples/MakerParts/Configuration_adv.h +++ b/config/examples/MakerParts/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Malyan/M150/Configuration_adv.h b/config/examples/Malyan/M150/Configuration_adv.h index 08628935ca..756943393e 100644 --- a/config/examples/Malyan/M150/Configuration_adv.h +++ b/config/examples/Malyan/M150/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Malyan/M200/Configuration_adv.h b/config/examples/Malyan/M200/Configuration_adv.h index f0d10447a9..9e2080ca77 100644 --- a/config/examples/Malyan/M200/Configuration_adv.h +++ b/config/examples/Malyan/M200/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Micromake/C1/enhanced/Configuration_adv.h b/config/examples/Micromake/C1/enhanced/Configuration_adv.h index f78f463de7..01c65c7c92 100644 --- a/config/examples/Micromake/C1/enhanced/Configuration_adv.h +++ b/config/examples/Micromake/C1/enhanced/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Mks/Sbase/Configuration_adv.h b/config/examples/Mks/Sbase/Configuration_adv.h index e46d3f9fd7..149b492a16 100644 --- a/config/examples/Mks/Sbase/Configuration_adv.h +++ b/config/examples/Mks/Sbase/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Modix/Big60/Configuration_adv.h b/config/examples/Modix/Big60/Configuration_adv.h index 7cba1762b8..a9dc1245e6 100644 --- a/config/examples/Modix/Big60/Configuration_adv.h +++ b/config/examples/Modix/Big60/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Nextion/Configuration_adv.h b/config/examples/Nextion/Configuration_adv.h index 250102511e..5fd2ed9a88 100644 --- a/config/examples/Nextion/Configuration_adv.h +++ b/config/examples/Nextion/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Ortur 4/Configuration_adv.h b/config/examples/Ortur 4/Configuration_adv.h index 23443636ef..616b18b720 100644 --- a/config/examples/Ortur 4/Configuration_adv.h +++ b/config/examples/Ortur 4/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Polargraph/Configuration_adv.h b/config/examples/Polargraph/Configuration_adv.h index 14dd681c6d..1f627bcf99 100644 --- a/config/examples/Polargraph/Configuration_adv.h +++ b/config/examples/Polargraph/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Prusa/MK3/Configuration_adv.h b/config/examples/Prusa/MK3/Configuration_adv.h index bfe5f48089..b3d95af84b 100644 --- a/config/examples/Prusa/MK3/Configuration_adv.h +++ b/config/examples/Prusa/MK3/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Prusa/MK3S-BigTreeTech-BTT002/Configuration_adv.h b/config/examples/Prusa/MK3S-BigTreeTech-BTT002/Configuration_adv.h index 46e101b197..89a513602e 100644 --- a/config/examples/Prusa/MK3S-BigTreeTech-BTT002/Configuration_adv.h +++ b/config/examples/Prusa/MK3S-BigTreeTech-BTT002/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Qidi/Qidi 1/Configuration_adv.h b/config/examples/Qidi/Qidi 1/Configuration_adv.h index 0d2cb0227e..9e1aa11c9d 100644 --- a/config/examples/Qidi/Qidi 1/Configuration_adv.h +++ b/config/examples/Qidi/Qidi 1/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Raiscube/A8r/Configuration_adv.h b/config/examples/Raiscube/A8r/Configuration_adv.h index 74d6ad688f..1d2dfb9b92 100644 --- a/config/examples/Raiscube/A8r/Configuration_adv.h +++ b/config/examples/Raiscube/A8r/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/RapideLite/RL200/Configuration_adv.h b/config/examples/RapideLite/RL200/Configuration_adv.h index 648f6dfe5a..a00a051c7b 100644 --- a/config/examples/RapideLite/RL200/Configuration_adv.h +++ b/config/examples/RapideLite/RL200/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Renkforce/RF100/Configuration_adv.h b/config/examples/Renkforce/RF100/Configuration_adv.h index ee510c7d1e..50424787e0 100644 --- a/config/examples/Renkforce/RF100/Configuration_adv.h +++ b/config/examples/Renkforce/RF100/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Renkforce/RF100XL/Configuration_adv.h b/config/examples/Renkforce/RF100XL/Configuration_adv.h index ee510c7d1e..50424787e0 100644 --- a/config/examples/Renkforce/RF100XL/Configuration_adv.h +++ b/config/examples/Renkforce/RF100XL/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Renkforce/RF100v2/Configuration_adv.h b/config/examples/Renkforce/RF100v2/Configuration_adv.h index ee510c7d1e..50424787e0 100644 --- a/config/examples/Renkforce/RF100v2/Configuration_adv.h +++ b/config/examples/Renkforce/RF100v2/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/RigidBot/Configuration_adv.h b/config/examples/RigidBot/Configuration_adv.h index 21a983553c..0b704efcb0 100644 --- a/config/examples/RigidBot/Configuration_adv.h +++ b/config/examples/RigidBot/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/SCARA/MP_SCARA/Configuration_adv.h b/config/examples/SCARA/MP_SCARA/Configuration_adv.h index 56057a4f09..08b5f08bef 100644 --- a/config/examples/SCARA/MP_SCARA/Configuration_adv.h +++ b/config/examples/SCARA/MP_SCARA/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/SCARA/Morgan/Configuration_adv.h b/config/examples/SCARA/Morgan/Configuration_adv.h index 01b288f457..1326c25201 100644 --- a/config/examples/SCARA/Morgan/Configuration_adv.h +++ b/config/examples/SCARA/Morgan/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/STM32/Black_STM32F407VET6/Configuration_adv.h b/config/examples/STM32/Black_STM32F407VET6/Configuration_adv.h index 2e1fb2a818..614b276f7e 100644 --- a/config/examples/STM32/Black_STM32F407VET6/Configuration_adv.h +++ b/config/examples/STM32/Black_STM32F407VET6/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Sanguinololu/Configuration_adv.h b/config/examples/Sanguinololu/Configuration_adv.h index 1ee7afa2e5..2b0c9e5922 100644 --- a/config/examples/Sanguinololu/Configuration_adv.h +++ b/config/examples/Sanguinololu/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Simulator/Configuration_adv.h b/config/examples/Simulator/Configuration_adv.h index 348284322e..41a1e41172 100644 --- a/config/examples/Simulator/Configuration_adv.h +++ b/config/examples/Simulator/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Sovol/SV-01/BigTreeTech SKR E3 Turbo/Configuration_adv.h b/config/examples/Sovol/SV-01/BigTreeTech SKR E3 Turbo/Configuration_adv.h index 9c3728a0d7..bf5b37d426 100644 --- a/config/examples/Sovol/SV-01/BigTreeTech SKR E3 Turbo/Configuration_adv.h +++ b/config/examples/Sovol/SV-01/BigTreeTech SKR E3 Turbo/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Sovol/SV-01/BigTreeTech SKR Mini E3 2.0/Configuration_adv.h b/config/examples/Sovol/SV-01/BigTreeTech SKR Mini E3 2.0/Configuration_adv.h index 3be992db5e..18d9603eb9 100644 --- a/config/examples/Sovol/SV-01/BigTreeTech SKR Mini E3 2.0/Configuration_adv.h +++ b/config/examples/Sovol/SV-01/BigTreeTech SKR Mini E3 2.0/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Sovol/SV-01/CrealityV22/Configuration_adv.h b/config/examples/Sovol/SV-01/CrealityV22/Configuration_adv.h index ada1876280..a54060fb4e 100644 --- a/config/examples/Sovol/SV-01/CrealityV22/Configuration_adv.h +++ b/config/examples/Sovol/SV-01/CrealityV22/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Sovol/SV-01/CrealityV221/Configuration_adv.h b/config/examples/Sovol/SV-01/CrealityV221/Configuration_adv.h index 07b790ad00..2aadc2d904 100644 --- a/config/examples/Sovol/SV-01/CrealityV221/Configuration_adv.h +++ b/config/examples/Sovol/SV-01/CrealityV221/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Sunlu/S8/Configuration_adv.h b/config/examples/Sunlu/S8/Configuration_adv.h index ff3a72b829..59bb11cd18 100644 --- a/config/examples/Sunlu/S8/Configuration_adv.h +++ b/config/examples/Sunlu/S8/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/TPARA/AXEL_TPARA/Configuration_adv.h b/config/examples/TPARA/AXEL_TPARA/Configuration_adv.h index a6a94708e7..cd63c2a8fa 100644 --- a/config/examples/TPARA/AXEL_TPARA/Configuration_adv.h +++ b/config/examples/TPARA/AXEL_TPARA/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Tevo/Michelangelo/Configuration_adv.h b/config/examples/Tevo/Michelangelo/Configuration_adv.h index 4fc23705df..ff6fbef497 100644 --- a/config/examples/Tevo/Michelangelo/Configuration_adv.h +++ b/config/examples/Tevo/Michelangelo/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Tevo/Nereus/Configuration_adv.h b/config/examples/Tevo/Nereus/Configuration_adv.h index 38f179c172..19cd2fce96 100644 --- a/config/examples/Tevo/Nereus/Configuration_adv.h +++ b/config/examples/Tevo/Nereus/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Tevo/Tarantula Pro/Configuration_adv.h b/config/examples/Tevo/Tarantula Pro/Configuration_adv.h index fcf66aa127..bfc551f7d1 100644 --- a/config/examples/Tevo/Tarantula Pro/Configuration_adv.h +++ b/config/examples/Tevo/Tarantula Pro/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Tevo/Tornado/V1 (MKS Base)/Configuration_adv.h b/config/examples/Tevo/Tornado/V1 (MKS Base)/Configuration_adv.h index 4a0e32a6a6..97415a46ed 100644 --- a/config/examples/Tevo/Tornado/V1 (MKS Base)/Configuration_adv.h +++ b/config/examples/Tevo/Tornado/V1 (MKS Base)/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Tevo/Tornado/V2 (MKS GEN-L)/Configuration_adv.h b/config/examples/Tevo/Tornado/V2 (MKS GEN-L)/Configuration_adv.h index 4a0e32a6a6..97415a46ed 100644 --- a/config/examples/Tevo/Tornado/V2 (MKS GEN-L)/Configuration_adv.h +++ b/config/examples/Tevo/Tornado/V2 (MKS GEN-L)/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/TheBorg/Configuration_adv.h b/config/examples/TheBorg/Configuration_adv.h index 382364d7ae..f5c404be8e 100644 --- a/config/examples/TheBorg/Configuration_adv.h +++ b/config/examples/TheBorg/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/TinyBoy2/Configuration_adv.h b/config/examples/TinyBoy2/Configuration_adv.h index 531af26b53..cd1b06a6fa 100644 --- a/config/examples/TinyBoy2/Configuration_adv.h +++ b/config/examples/TinyBoy2/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Tronxy/X3A/Configuration_adv.h b/config/examples/Tronxy/X3A/Configuration_adv.h index 83115f3d5c..5f01569b35 100644 --- a/config/examples/Tronxy/X3A/Configuration_adv.h +++ b/config/examples/Tronxy/X3A/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Tronxy/X5S-2E/Configuration_adv.h b/config/examples/Tronxy/X5S-2E/Configuration_adv.h index 4427445de5..c3897a9e71 100644 --- a/config/examples/Tronxy/X5S-2E/Configuration_adv.h +++ b/config/examples/Tronxy/X5S-2E/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Tronxy/X5SA-2E/Configuration_adv.h b/config/examples/Tronxy/X5SA-2E/Configuration_adv.h index 8fdd33e5d0..c10c499bc6 100644 --- a/config/examples/Tronxy/X5SA-2E/Configuration_adv.h +++ b/config/examples/Tronxy/X5SA-2E/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Tronxy/X5SA/Configuration_adv.h b/config/examples/Tronxy/X5SA/Configuration_adv.h index d0123d8077..6d71775532 100644 --- a/config/examples/Tronxy/X5SA/Configuration_adv.h +++ b/config/examples/Tronxy/X5SA/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Two Trees/BlueR Plus/Configuration_adv.h b/config/examples/Two Trees/BlueR Plus/Configuration_adv.h index 7d5867c9fe..2f0788abe3 100644 --- a/config/examples/Two Trees/BlueR Plus/Configuration_adv.h +++ b/config/examples/Two Trees/BlueR Plus/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Two Trees/BlueR/BlueR V1/Configuration_adv.h b/config/examples/Two Trees/BlueR/BlueR V1/Configuration_adv.h index c7e99afeb2..6000419ac2 100644 --- a/config/examples/Two Trees/BlueR/BlueR V1/Configuration_adv.h +++ b/config/examples/Two Trees/BlueR/BlueR V1/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Two Trees/BlueR/BlueR V2/Configuration_adv.h b/config/examples/Two Trees/BlueR/BlueR V2/Configuration_adv.h index c7e99afeb2..6000419ac2 100644 --- a/config/examples/Two Trees/BlueR/BlueR V2/Configuration_adv.h +++ b/config/examples/Two Trees/BlueR/BlueR V2/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Two Trees/BlueR/BlueR V3/Configuration_adv.h b/config/examples/Two Trees/BlueR/BlueR V3/Configuration_adv.h index c7e99afeb2..6000419ac2 100644 --- a/config/examples/Two Trees/BlueR/BlueR V3/Configuration_adv.h +++ b/config/examples/Two Trees/BlueR/BlueR V3/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Two Trees/Sapphire Plus/Sapphire Plus V2/Configuration_adv.h b/config/examples/Two Trees/Sapphire Plus/Sapphire Plus V2/Configuration_adv.h index 05d683a535..6c02625ed7 100644 --- a/config/examples/Two Trees/Sapphire Plus/Sapphire Plus V2/Configuration_adv.h +++ b/config/examples/Two Trees/Sapphire Plus/Sapphire Plus V2/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Two Trees/Sapphire Pro/Configuration_adv.h b/config/examples/Two Trees/Sapphire Pro/Configuration_adv.h index 4fa465378a..ebe86b0922 100644 --- a/config/examples/Two Trees/Sapphire Pro/Configuration_adv.h +++ b/config/examples/Two Trees/Sapphire Pro/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/UltiMachine/Archim1/Configuration_adv.h b/config/examples/UltiMachine/Archim1/Configuration_adv.h index e6698340e3..85b119f2e7 100644 --- a/config/examples/UltiMachine/Archim1/Configuration_adv.h +++ b/config/examples/UltiMachine/Archim1/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/UltiMachine/Archim2/Configuration_adv.h b/config/examples/UltiMachine/Archim2/Configuration_adv.h index c8af89bf2d..a9b776a0c7 100644 --- a/config/examples/UltiMachine/Archim2/Configuration_adv.h +++ b/config/examples/UltiMachine/Archim2/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Ultimaker/Ultimaker 2/Configuration_adv.h b/config/examples/Ultimaker/Ultimaker 2/Configuration_adv.h index c7b939f3d3..95e122933e 100644 --- a/config/examples/Ultimaker/Ultimaker 2/Configuration_adv.h +++ b/config/examples/Ultimaker/Ultimaker 2/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Ultimaker/Ultimaker Original (1.5.7)/Configuration_adv.h b/config/examples/Ultimaker/Ultimaker Original (1.5.7)/Configuration_adv.h index a13d5cc7f3..cf9132e342 100644 --- a/config/examples/Ultimaker/Ultimaker Original (1.5.7)/Configuration_adv.h +++ b/config/examples/Ultimaker/Ultimaker Original (1.5.7)/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Ultimaker/Ultimaker Original Plus (2.1.1)/Configuration_adv.h b/config/examples/Ultimaker/Ultimaker Original Plus (2.1.1)/Configuration_adv.h index 6b22d61d4a..217d7063d7 100644 --- a/config/examples/Ultimaker/Ultimaker Original Plus (2.1.1)/Configuration_adv.h +++ b/config/examples/Ultimaker/Ultimaker Original Plus (2.1.1)/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/VORONDesign/Configuration_adv.h b/config/examples/VORONDesign/Configuration_adv.h index 41ee970f24..96e1525920 100644 --- a/config/examples/VORONDesign/Configuration_adv.h +++ b/config/examples/VORONDesign/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Velleman/K8200/Configuration_adv.h b/config/examples/Velleman/K8200/Configuration_adv.h index efbf5a564f..e199cfac34 100644 --- a/config/examples/Velleman/K8200/Configuration_adv.h +++ b/config/examples/Velleman/K8200/Configuration_adv.h @@ -147,24 +147,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Velleman/K8400/Dual-head/Configuration_adv.h b/config/examples/Velleman/K8400/Dual-head/Configuration_adv.h index f7eacbea35..b4b19f132a 100644 --- a/config/examples/Velleman/K8400/Dual-head/Configuration_adv.h +++ b/config/examples/Velleman/K8400/Dual-head/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Velleman/K8400/Single-head/Configuration_adv.h b/config/examples/Velleman/K8400/Single-head/Configuration_adv.h index f7eacbea35..b4b19f132a 100644 --- a/config/examples/Velleman/K8400/Single-head/Configuration_adv.h +++ b/config/examples/Velleman/K8400/Single-head/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/WASP/PowerWASP/Configuration_adv.h b/config/examples/WASP/PowerWASP/Configuration_adv.h index 76374c1f1c..e6b76e1100 100644 --- a/config/examples/WASP/PowerWASP/Configuration_adv.h +++ b/config/examples/WASP/PowerWASP/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Wanhao/Duplicator 4S/Configuration_adv.h b/config/examples/Wanhao/Duplicator 4S/Configuration_adv.h index a37f7a4750..ee6f5a845b 100644 --- a/config/examples/Wanhao/Duplicator 4S/Configuration_adv.h +++ b/config/examples/Wanhao/Duplicator 4S/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Wanhao/Duplicator 6/Configuration_adv.h b/config/examples/Wanhao/Duplicator 6/Configuration_adv.h index 98eef527b8..b95bcb63c1 100644 --- a/config/examples/Wanhao/Duplicator 6/Configuration_adv.h +++ b/config/examples/Wanhao/Duplicator 6/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Wanhao/Duplicator i3 2.1/Configuration_adv.h b/config/examples/Wanhao/Duplicator i3 2.1/Configuration_adv.h index d91adce56c..86c0d7fdff 100644 --- a/config/examples/Wanhao/Duplicator i3 2.1/Configuration_adv.h +++ b/config/examples/Wanhao/Duplicator i3 2.1/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Wanhao/Duplicator i3 Mini/Configuration_adv.h b/config/examples/Wanhao/Duplicator i3 Mini/Configuration_adv.h index cb19eb4384..4a9a5f73a1 100644 --- a/config/examples/Wanhao/Duplicator i3 Mini/Configuration_adv.h +++ b/config/examples/Wanhao/Duplicator i3 Mini/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Weedo/Tina2/V2/Configuration_adv.h b/config/examples/Weedo/Tina2/V2/Configuration_adv.h index edb5dfe767..d62e763127 100644 --- a/config/examples/Weedo/Tina2/V2/Configuration_adv.h +++ b/config/examples/Weedo/Tina2/V2/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Weedo/Tina2/V3/Configuration_adv.h b/config/examples/Weedo/Tina2/V3/Configuration_adv.h index edb5dfe767..d62e763127 100644 --- a/config/examples/Weedo/Tina2/V3/Configuration_adv.h +++ b/config/examples/Weedo/Tina2/V3/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Weistek/wt150/Configuration_adv.h b/config/examples/Weistek/wt150/Configuration_adv.h index aaad7c6ec8..dab4bccc1f 100644 --- a/config/examples/Weistek/wt150/Configuration_adv.h +++ b/config/examples/Weistek/wt150/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Zonestar/P802M/Configuration_adv.h b/config/examples/Zonestar/P802M/Configuration_adv.h index 4f3038cd0b..ca5df4a8c2 100644 --- a/config/examples/Zonestar/P802M/Configuration_adv.h +++ b/config/examples/Zonestar/P802M/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Zonestar/P802QR2/BigTreeTech SKR 1.4 Turbo (A4988)/Configuration_adv.h b/config/examples/Zonestar/P802QR2/BigTreeTech SKR 1.4 Turbo (A4988)/Configuration_adv.h index 2f249d2de6..d92efd23c7 100644 --- a/config/examples/Zonestar/P802QR2/BigTreeTech SKR 1.4 Turbo (A4988)/Configuration_adv.h +++ b/config/examples/Zonestar/P802QR2/BigTreeTech SKR 1.4 Turbo (A4988)/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/Zonestar/P802QR2/BigTreeTech SKR 1.4 Turbo (TMC2209)/Configuration_adv.h b/config/examples/Zonestar/P802QR2/BigTreeTech SKR 1.4 Turbo (TMC2209)/Configuration_adv.h index 3c66f8edca..6c0db1681f 100755 --- a/config/examples/Zonestar/P802QR2/BigTreeTech SKR 1.4 Turbo (TMC2209)/Configuration_adv.h +++ b/config/examples/Zonestar/P802QR2/BigTreeTech SKR 1.4 Turbo (TMC2209)/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/delta/Anycubic/Kossel Linear Plus/Configuration_adv.h b/config/examples/delta/Anycubic/Kossel Linear Plus/Configuration_adv.h index 35ca5c5ee0..b7622efb8e 100644 --- a/config/examples/delta/Anycubic/Kossel Linear Plus/Configuration_adv.h +++ b/config/examples/delta/Anycubic/Kossel Linear Plus/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/delta/Anycubic/Kossel/Configuration_adv.h b/config/examples/delta/Anycubic/Kossel/Configuration_adv.h index 203fa2580d..953cf21523 100644 --- a/config/examples/delta/Anycubic/Kossel/Configuration_adv.h +++ b/config/examples/delta/Anycubic/Kossel/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/delta/Anycubic/Predator/Configuration_adv.h b/config/examples/delta/Anycubic/Predator/Configuration_adv.h index b28f38edf7..5524d642b9 100644 --- a/config/examples/delta/Anycubic/Predator/Configuration_adv.h +++ b/config/examples/delta/Anycubic/Predator/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/delta/Dreammaker/Overlord/Configuration_adv.h b/config/examples/delta/Dreammaker/Overlord/Configuration_adv.h index 2e431cefe2..9a4c08b670 100644 --- a/config/examples/delta/Dreammaker/Overlord/Configuration_adv.h +++ b/config/examples/delta/Dreammaker/Overlord/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/delta/Dreammaker/Overlord_Pro/Configuration_adv.h b/config/examples/delta/Dreammaker/Overlord_Pro/Configuration_adv.h index 2e431cefe2..9a4c08b670 100644 --- a/config/examples/delta/Dreammaker/Overlord_Pro/Configuration_adv.h +++ b/config/examples/delta/Dreammaker/Overlord_Pro/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/delta/FLSUN/Q5-nano_v1/Configuration_adv.h b/config/examples/delta/FLSUN/Q5-nano_v1/Configuration_adv.h index 47cde4aa8a..cdefec4f5d 100644 --- a/config/examples/delta/FLSUN/Q5-nano_v1/Configuration_adv.h +++ b/config/examples/delta/FLSUN/Q5-nano_v1/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/delta/FLSUN/QQ-S/Configuration_adv.h b/config/examples/delta/FLSUN/QQ-S/Configuration_adv.h index d2d15839f8..4850394e46 100644 --- a/config/examples/delta/FLSUN/QQ-S/Configuration_adv.h +++ b/config/examples/delta/FLSUN/QQ-S/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/delta/FLSUN/QQS-Pro/Configuration_adv.h b/config/examples/delta/FLSUN/QQS-Pro/Configuration_adv.h index 4a09a1dd27..7aa5003dc6 100644 --- a/config/examples/delta/FLSUN/QQS-Pro/Configuration_adv.h +++ b/config/examples/delta/FLSUN/QQS-Pro/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/delta/FLSUN/auto_calibrate/Configuration_adv.h b/config/examples/delta/FLSUN/auto_calibrate/Configuration_adv.h index c496e5ae71..ef995b7e6a 100644 --- a/config/examples/delta/FLSUN/auto_calibrate/Configuration_adv.h +++ b/config/examples/delta/FLSUN/auto_calibrate/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/delta/FLSUN/kossel/Configuration_adv.h b/config/examples/delta/FLSUN/kossel/Configuration_adv.h index c496e5ae71..ef995b7e6a 100644 --- a/config/examples/delta/FLSUN/kossel/Configuration_adv.h +++ b/config/examples/delta/FLSUN/kossel/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/delta/FLSUN/kossel_mini/Configuration_adv.h b/config/examples/delta/FLSUN/kossel_mini/Configuration_adv.h index 6f52710aa3..fd8045a958 100644 --- a/config/examples/delta/FLSUN/kossel_mini/Configuration_adv.h +++ b/config/examples/delta/FLSUN/kossel_mini/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/delta/Geeetech/G2/Configuration_adv.h b/config/examples/delta/Geeetech/G2/Configuration_adv.h index 7dd7ef6d82..5c7e69e958 100644 --- a/config/examples/delta/Geeetech/G2/Configuration_adv.h +++ b/config/examples/delta/Geeetech/G2/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/delta/Geeetech/G2Pro/Configuration_adv.h b/config/examples/delta/Geeetech/G2Pro/Configuration_adv.h index 860fcc8292..fcf866d7d2 100644 --- a/config/examples/delta/Geeetech/G2Pro/Configuration_adv.h +++ b/config/examples/delta/Geeetech/G2Pro/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/delta/Geeetech/G2S/Configuration_adv.h b/config/examples/delta/Geeetech/G2S/Configuration_adv.h index 860fcc8292..fcf866d7d2 100644 --- a/config/examples/delta/Geeetech/G2S/Configuration_adv.h +++ b/config/examples/delta/Geeetech/G2S/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/delta/Geeetech/G2SPro/Configuration_adv.h b/config/examples/delta/Geeetech/G2SPro/Configuration_adv.h index 860fcc8292..fcf866d7d2 100644 --- a/config/examples/delta/Geeetech/G2SPro/Configuration_adv.h +++ b/config/examples/delta/Geeetech/G2SPro/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/delta/Geeetech/Rostock 301/Configuration_adv.h b/config/examples/delta/Geeetech/Rostock 301/Configuration_adv.h index 851d443e99..6fbcc2d695 100644 --- a/config/examples/delta/Geeetech/Rostock 301/Configuration_adv.h +++ b/config/examples/delta/Geeetech/Rostock 301/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/delta/Hatchbox_Alpha/Configuration_adv.h b/config/examples/delta/Hatchbox_Alpha/Configuration_adv.h index 117f754e01..99ae322cfe 100644 --- a/config/examples/delta/Hatchbox_Alpha/Configuration_adv.h +++ b/config/examples/delta/Hatchbox_Alpha/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/delta/MKS/SBASE/Configuration_adv.h b/config/examples/delta/MKS/SBASE/Configuration_adv.h index 35c168f969..d1d49ff297 100644 --- a/config/examples/delta/MKS/SBASE/Configuration_adv.h +++ b/config/examples/delta/MKS/SBASE/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/delta/Malyan M300/Configuration_adv.h b/config/examples/delta/Malyan M300/Configuration_adv.h index 41267ba7fe..b91c8e6fcd 100644 --- a/config/examples/delta/Malyan M300/Configuration_adv.h +++ b/config/examples/delta/Malyan M300/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/delta/Tevo Little Monster/Configuration_adv.h b/config/examples/delta/Tevo Little Monster/Configuration_adv.h index 6b4d3749f6..058c7ef050 100644 --- a/config/examples/delta/Tevo Little Monster/Configuration_adv.h +++ b/config/examples/delta/Tevo Little Monster/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/delta/generic/Configuration_adv.h b/config/examples/delta/generic/Configuration_adv.h index 6f52710aa3..fd8045a958 100644 --- a/config/examples/delta/generic/Configuration_adv.h +++ b/config/examples/delta/generic/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/delta/kossel_clear/Configuration_adv.h b/config/examples/delta/kossel_clear/Configuration_adv.h index 26dfdacdda..86aaddf81d 100644 --- a/config/examples/delta/kossel_clear/Configuration_adv.h +++ b/config/examples/delta/kossel_clear/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/delta/kossel_xl/Configuration_adv.h b/config/examples/delta/kossel_xl/Configuration_adv.h index 84e91e053a..444a1dc74e 100644 --- a/config/examples/delta/kossel_xl/Configuration_adv.h +++ b/config/examples/delta/kossel_xl/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/gCreate/gMax1.5+/Configuration_adv.h b/config/examples/gCreate/gMax1.5+/Configuration_adv.h index 6b0846b405..6c44480a22 100644 --- a/config/examples/gCreate/gMax1.5+/Configuration_adv.h +++ b/config/examples/gCreate/gMax1.5+/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/linear_axes/RAMPS 5 LINEAR_AXES/Configuration_adv.h b/config/examples/linear_axes/RAMPS 5 LINEAR_AXES/Configuration_adv.h index 2107f2eb69..27dafa70b7 100644 --- a/config/examples/linear_axes/RAMPS 5 LINEAR_AXES/Configuration_adv.h +++ b/config/examples/linear_axes/RAMPS 5 LINEAR_AXES/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/makibox/Configuration_adv.h b/config/examples/makibox/Configuration_adv.h index 0f26ffa729..a2d4ecd807 100644 --- a/config/examples/makibox/Configuration_adv.h +++ b/config/examples/makibox/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/config/examples/tvrrug/Round2/Configuration_adv.h b/config/examples/tvrrug/Round2/Configuration_adv.h index 4630ca2fa4..9173800c2e 100644 --- a/config/examples/tvrrug/Round2/Configuration_adv.h +++ b/config/examples/tvrrug/Round2/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. |