path: root/Marlin/src/gcode/calibrate/G34_M422.cpp

/**
 * Marlin 3D Printer Firmware
 * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
 *
 * Based on Sprinter and grbl.
 * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
 *
 * This program is free software: you can redistribute it and/or modify
 * it under the terms of the GNU General Public License as published by
 * the Free Software Foundation, either version 3 of the License, or
 * (at your option) any later version.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 * GNU General Public License for more details.
 *
 * You should have received a copy of the GNU General Public License
 * along with this program.  If not, see <https://www.gnu.org/licenses/>.
 *
 */

#include "../../inc/MarlinConfigPre.h"

#if EITHER(Z_MULTI_ENDSTOPS, Z_STEPPER_AUTO_ALIGN)

#include "../../feature/z_stepper_align.h"

#include "../gcode.h"
#include "../../module/motion.h"
#include "../../module/stepper.h"
#include "../../module/planner.h"
#include "../../module/probe.h"
#include "../../lcd/marlinui.h" // for LCD_MESSAGE

#if HAS_LEVELING
  #include "../../feature/bedlevel/bedlevel.h"
#endif

#if HAS_MULTI_HOTEND
  #include "../../module/tool_change.h"
#endif

#if HAS_Z_STEPPER_ALIGN_STEPPER_XY
  #include "../../libs/least_squares_fit.h"
#endif

#if ENABLED(BLTOUCH)
  #include "../../feature/bltouch.h"
#endif

#define DEBUG_OUT ENABLED(DEBUG_LEVELING_FEATURE)
#include "../../core/debug_out.h"

#if NUM_Z_STEPPERS >= 3
  #define TRIPLE_Z 1
  #if NUM_Z_STEPPERS >= 4
    #define QUAD_Z 1
  #endif
#endif

/**
 * G34: Z-Stepper automatic alignment
 *
 * Manual stepper lock controls (reset by G28):
 *   L                 Unlock all steppers
 *   Z<1-4>            Z stepper to lock / unlock
 *   S<state>          0=UNLOCKED 1=LOCKED. If omitted, assume LOCKED.
 *
 *   Examples:
 *     G34 Z1     ; Lock Z1
 *     G34 L Z2   ; Unlock all, then lock Z2
 *     G34 Z2 S0  ; Unlock Z2
 *
 * With Z_STEPPER_AUTO_ALIGN:
 *   I<iterations>     Number of tests. If omitted, Z_STEPPER_ALIGN_ITERATIONS.
 *   T<accuracy>       Target Accuracy factor. If omitted, Z_STEPPER_ALIGN_ACC.
 *   A<amplification>  Provide an Amplification value. If omitted, Z_STEPPER_ALIGN_AMP.
 *   R                 Flag to recalculate points based on current probe offsets
 */
void GcodeSuite::G34() {
  DEBUG_SECTION(log_G34, "G34", DEBUGGING(LEVELING));
  if (DEBUGGING(LEVELING)) log_machine_info();

  planner.synchronize();  // Prevent damage

  const bool seenL = parser.seen('L');
  if (seenL) stepper.set_all_z_lock(false);

  const bool seenZ = parser.seenval('Z');
  if (seenZ) {
    const bool state = parser.boolval('S', true);
    switch (parser.intval('Z')) {
      case 1: stepper.set_z1_lock(state); break;
      case 2: stepper.set_z2_lock(state); break;
      #if TRIPLE_Z
        case 3: stepper.set_z3_lock(state); break;
        #if QUAD_Z
          case 4: stepper.set_z4_lock(state); break;
        #endif
      #endif
    }
  }

  if (seenL || seenZ) {
    stepper.set_separate_multi_axis(seenZ);
    return;
  }

  #if ENABLED(Z_STEPPER_AUTO_ALIGN)
    do { // break out on error

      const int8_t z_auto_align_iterations = parser.intval('I', Z_STEPPER_ALIGN_ITERATIONS);
      if (!WITHIN(z_auto_align_iterations, 1, 30)) {
        SERIAL_ECHOLNPGM("?(I)teration out of bounds (1-30).");
        break;
      }

      const float z_auto_align_accuracy = parser.floatval('T', Z_STEPPER_ALIGN_ACC);
      if (!WITHIN(z_auto_align_accuracy, 0.01f, 1.0f)) {
        SERIAL_ECHOLNPGM("?(T)arget accuracy out of bounds (0.01-1.0).");
        break;
      }

      const float z_auto_align_amplification = TERN(HAS_Z_STEPPER_ALIGN_STEPPER_XY, Z_STEPPER_ALIGN_AMP, parser.floatval('A', Z_STEPPER_ALIGN_AMP));
      if (!WITHIN(ABS(z_auto_align_amplification), 0.5f, 2.0f)) {
        SERIAL_ECHOLNPGM("?(A)mplification out of bounds (0.5-2.0).");
        break;
      }

      if (parser.seen('R')) z_stepper_align.reset_to_default();

      const ProbePtRaise raise_after = parser.boolval('E') ? PROBE_PT_STOW : PROBE_PT_RAISE;

      // Disable the leveling matrix before auto-aligning
      #if HAS_LEVELING
        #if ENABLED(RESTORE_LEVELING_AFTER_G34)
          const bool leveling_was_active = planner.leveling_active;
        #endif
        set_bed_leveling_enabled(false);
      #endif

      TERN_(CNC_WORKSPACE_PLANES, workspace_plane = PLANE_XY);

      // Always home with tool 0 active
      #if HAS_MULTI_HOTEND
        const uint8_t old_tool_index = active_extruder;
        tool_change(0, true);
      #endif

      TERN_(HAS_DUPLICATION_MODE, set_duplication_enabled(false));

      // In BLTOUCH HS mode, the probe travels in a deployed state.
      // Users of G34 might have a badly misaligned bed, so raise Z by the
      // length of the deployed pin (BLTOUCH stroke < 7mm)
      #define Z_BASIC_CLEARANCE (Z_CLEARANCE_BETWEEN_PROBES + TERN0(BLTOUCH, bltouch.z_extra_clearance()))

      // Compute a worst-case clearance height to probe from. After the first
      // iteration this will be re-calculated based on the actual bed position
      auto magnitude2 = [&](const uint8_t i, const uint8_t j) {
        const xy_pos_t diff = z_stepper_align.xy[i] - z_stepper_align.xy[j];
        return HYPOT2(diff.x, diff.y);
      };
      float z_probe = Z_BASIC_CLEARANCE + (G34_MAX_GRADE) * 0.01f * SQRT(_MAX(0, magnitude2(0, 1)
        #if TRIPLE_Z
          , magnitude2(2, 1), magnitude2(2, 0)
          #if QUAD_Z
            , magnitude2(3, 2), magnitude2(3, 1), magnitude2(3, 0)
          #endif
        #endif
      ));

      // Home before the alignment procedure
      home_if_needed();

      // Move the Z coordinate realm towards the positive - dirty trick
      current_position.z += z_probe * 0.5f;
      sync_plan_position();
      // Now, the Z origin lies below the build plate. That allows to probe deeper, before run_z_probe throws an error.
      // This hack is un-done at the end of G34 - either by re-homing, or by using the probed heights of the last iteration.

      #if !HAS_Z_STEPPER_ALIGN_STEPPER_XY
        float last_z_align_move[NUM_Z_STEPPERS] = ARRAY_N_1(NUM_Z_STEPPERS, 10000.0f);
      #else
        float last_z_align_level_indicator = 10000.0f;
      #endif
      float z_measured[NUM_Z_STEPPERS] = { 0 },
            z_maxdiff = 0.0f,
            amplification = z_auto_align_amplification;

      #if !HAS_Z_STEPPER_ALIGN_STEPPER_XY
        bool adjustment_reverse = false;
      #endif

      #if HAS_STATUS_MESSAGE
        PGM_P const msg_iteration = GET_TEXT(MSG_ITERATION);
        const uint8_t iter_str_len = strlen_P(msg_iteration);
      #endif

      // Final z and iteration values will be used after breaking the loop
      float z_measured_min;
      uint8_t iteration = 0;
      bool err_break = false; // To break out of nested loops
      while (iteration < z_auto_align_iterations) {
        if (DEBUGGING(LEVELING)) DEBUG_ECHOLNPGM("> probing all positions.");

        const int iter = iteration + 1;
        SERIAL_ECHOLNPGM("\nG34 Iteration: ", iter);
        #if HAS_STATUS_MESSAGE
          char str[iter_str_len + 2 + 1];
          sprintf_P(str, msg_iteration, iter);
          ui.set_status(str);
        #endif

        // Initialize minimum value
        z_measured_min =  100000.0f;
        float z_measured_max = -100000.0f;

        // Probe all positions (one per Z-Stepper)
        LOOP_L_N(i, NUM_Z_STEPPERS) {
          // iteration odd/even --> downward / upward stepper sequence
          const uint8_t iprobe = (iteration & 1) ? NUM_Z_STEPPERS - 1 - i : i;

          // Safe clearance even on an incline
          if ((iteration == 0 || i > 0) && z_probe > current_position.z) do_blocking_move_to_z(z_probe);

          xy_pos_t &ppos = z_stepper_align.xy[iprobe];

          if (DEBUGGING(LEVELING))
            DEBUG_ECHOLNPGM_P(PSTR("Probing X"), ppos.x, SP_Y_STR, ppos.y);

          // Probe a Z height for each stepper.
          // Probing sanity check is disabled, as it would trigger even in normal cases because
          // current_position.z has been manually altered in the "dirty trick" above.
          const float z_probed_height = probe.probe_at_point(DIFF_TERN(HAS_HOME_OFFSET, ppos, xy_pos_t(home_offset)), raise_after, 0, true, false);
          if (isnan(z_probed_height)) {
            SERIAL_ECHOLNPGM("Probing failed");
            LCD_MESSAGE(MSG_LCD_PROBING_FAILED);
            err_break = true;
            break;
          }

          // Add height to each value, to provide a more useful target height for
          // the next iteration of probing. This allows adjustments to be made away from the bed.
          z_measured[iprobe] = z_probed_height + Z_CLEARANCE_BETWEEN_PROBES;

          if (DEBUGGING(LEVELING)) DEBUG_ECHOLNPGM("> Z", iprobe + 1, " measured position is ", z_measured[iprobe]);

          // Remember the minimum measurement to calculate the correction later on
          z_measured_min = _MIN(z_measured_min, z_measured[iprobe]);
          z_measured_max = _MAX(z_measured_max, z_measured[iprobe]);
        } // for (i)

        if (err_break) break;

        // Adapt the next probe clearance height based on the new measurements.
        // Safe_height = lowest distance to bed (= highest measurement) plus highest measured misalignment.
        z_maxdiff = z_measured_max - z_measured_min;
        z_probe = Z_BASIC_CLEARANCE + z_measured_max + z_maxdiff;

        #if HAS_Z_STEPPER_ALIGN_STEPPER_XY
          // Replace the initial values in z_measured with calculated heights at
          // each stepper position. This allows the adjustment algorithm to be
          // shared between both possible probing mechanisms.

          // This must be done after the next z_probe height is calculated, so that
          // the height is calculated from actual print area positions, and not
          // extrapolated motor movements.

          // Compute the least-squares fit for all probed points.
          // Calculate the Z position of each stepper and store it in z_measured.
          // This allows the actual adjustment logic to be shared by both algorithms.
          linear_fit_data lfd;
          incremental_LSF_reset(&lfd);
          LOOP_L_N(i, NUM_Z_STEPPERS) {
            SERIAL_ECHOLNPGM("PROBEPT_", i, ": ", z_measured[i]);
            incremental_LSF(&lfd, z_stepper_align.xy[i], z_measured[i]);
          }
          finish_incremental_LSF(&lfd);

          z_measured_min = 100000.0f;
          LOOP_L_N(i, NUM_Z_STEPPERS) {
            z_measured[i] = -(lfd.A * z_stepper_align.stepper_xy[i].x + lfd.B * z_stepper_align.stepper_xy[i].y + lfd.D);
            z_measured_min = _MIN(z_measured_min, z_measured[i]);
          }

          SERIAL_ECHOLNPGM(
            LIST_N(DOUBLE(NUM_Z_STEPPERS),
              "Calculated Z1=", z_measured[0],
                        " Z2=", z_measured[1],
                        " Z3=", z_measured[2],
                        " Z4=", z_measured[3]
            )
          );
        #endif

        SERIAL_ECHOLNPGM("\n"
          "Z2-Z1=", ABS(z_measured[1] - z_measured[0])
          #if TRIPLE_Z
            , " Z3-Z2=", ABS(z_measured[2] - z_measured[1])
            , " Z3-Z1=", ABS(z_measured[2] - z_measured[0])
            #if QUAD_Z
              , " Z4-Z3=", ABS(z_measured[3] - z_measured[2])
              , " Z4-Z2=", ABS(z_measured[3] - z_measured[1])
              , " Z4-Z1=", ABS(z_measured[3] - z_measured[0])
            #endif
          #endif
        );

        #if HAS_STATUS_MESSAGE
          char fstr1[10];
          char msg[6 + (6 + 5) * NUM_Z_STEPPERS + 1]
            #if TRIPLE_Z
              , fstr2[10], fstr3[10]
              #if QUAD_Z
                , fstr4[10], fstr5[10], fstr6[10]
              #endif
            #endif
          ;
          sprintf_P(msg,
            PSTR("1:2=%s" TERN_(TRIPLE_Z, " 3-2=%s 3-1=%s") TERN_(QUAD_Z, " 4-3=%s 4-2=%s 4-1=%s")),
            dtostrf(ABS(z_measured[1] - z_measured[0]), 1, 3, fstr1)
            OPTARG(TRIPLE_Z,
              dtostrf(ABS(z_measured[2] - z_measured[1]), 1, 3, fstr2),
              dtostrf(ABS(z_measured[2] - z_measured[0]), 1, 3, fstr3))
            OPTARG(QUAD_Z,
              dtostrf(ABS(z_measured[3] - z_measured[2]), 1, 3, fstr4),
              dtostrf(ABS(z_measured[3] - z_measured[1]), 1, 3, fstr5),
              dtostrf(ABS(z_measured[3] - z_measured[0]), 1, 3, fstr6))
          );
          ui.set_status(msg);
        #endif

        auto decreasing_accuracy = [](const_float_t v1, const_float_t v2) {
          if (v1 < v2 * 0.7f) {
            SERIAL_ECHOLNPGM("Decreasing Accuracy Detected.");
            LCD_MESSAGE(MSG_DECREASING_ACCURACY);
            return true;
          }
          return false;
        };

        #if HAS_Z_STEPPER_ALIGN_STEPPER_XY
          // Check if the applied corrections go in the correct direction.
          // Calculate the sum of the absolute deviations from the mean of the probe measurements.
          // Compare to the last iteration to ensure it's getting better.

          // Calculate mean value as a reference
          float z_measured_mean = 0.0f;
          LOOP_L_N(zstepper, NUM_Z_STEPPERS) z_measured_mean += z_measured[zstepper];
          z_measured_mean /= NUM_Z_STEPPERS;

          // Calculate the sum of the absolute deviations from the mean value
          float z_align_level_indicator = 0.0f;
          LOOP_L_N(zstepper, NUM_Z_STEPPERS)
            z_align_level_indicator += ABS(z_measured[zstepper] - z_measured_mean);

          // If it's getting worse, stop and throw an error
          err_break = decreasing_accuracy(last_z_align_level_indicator, z_align_level_indicator);
          if (err_break) break;

          last_z_align_level_indicator = z_align_level_indicator;
        #endif

        // The following correction actions are to be enabled for select Z-steppers only
        stepper.set_separate_multi_axis(true);

        bool success_break = true;
        // Correct the individual stepper offsets
        LOOP_L_N(zstepper, NUM_Z_STEPPERS) {
          // Calculate current stepper move
          float z_align_move = z_measured[zstepper] - z_measured_min;
          const float z_align_abs = ABS(z_align_move);

          #if !HAS_Z_STEPPER_ALIGN_STEPPER_XY
            // Optimize one iteration's correction based on the first measurements
            if (z_align_abs) amplification = (iteration == 1) ? _MIN(last_z_align_move[zstepper] / z_align_abs, 2.0f) : z_auto_align_amplification;

            // Check for less accuracy compared to last move
            if (decreasing_accuracy(last_z_align_move[zstepper], z_align_abs)) {
              if (DEBUGGING(LEVELING)) DEBUG_ECHOLNPGM("> Z", zstepper + 1, " last_z_align_move = ", last_z_align_move[zstepper]);
              if (DEBUGGING(LEVELING)) DEBUG_ECHOLNPGM("> Z", zstepper + 1, " z_align_abs = ", z_align_abs);
              adjustment_reverse = !adjustment_reverse;
            }

            // Remember the alignment for the next iteration, but only if steppers move,
            // otherwise it would be just zero (in case this stepper was at z_measured_min already)
            if (z_align_abs > 0) last_z_align_move[zstepper] = z_align_abs;
          #endif

          // Stop early if all measured points achieve accuracy target
          if (z_align_abs > z_auto_align_accuracy) success_break = false;

          if (DEBUGGING(LEVELING)) DEBUG_ECHOLNPGM("> Z", zstepper + 1, " corrected by ", z_align_move);

          // Lock all steppers except one
          stepper.set_all_z_lock(true, zstepper);

          #if !HAS_Z_STEPPER_ALIGN_STEPPER_XY
            // Decreasing accuracy was detected so move was inverted.
            // Will match reversed Z steppers on dual steppers. Triple will need more work to map.
            if (adjustment_reverse) {
              z_align_move = -z_align_move;
              if (DEBUGGING(LEVELING)) DEBUG_ECHOLNPGM("> Z", zstepper + 1, " correction reversed to ", z_align_move);
            }
          #endif

          // Do a move to correct part of the misalignment for the current stepper
          do_blocking_move_to_z(amplification * z_align_move + current_position.z);
        } // for (zstepper)

        // Back to normal stepper operations
        stepper.set_all_z_lock(false);
        stepper.set_separate_multi_axis(false);

        if (err_break) break;

        if (success_break) {
          SERIAL_ECHOLNPGM("Target accuracy achieved.");
          LCD_MESSAGE(MSG_ACCURACY_ACHIEVED);
          break;
        }

        iteration++;
      } // while (iteration < z_auto_align_iterations)

      if (err_break)
        SERIAL_ECHOLNPGM("G34 aborted.");
      else {
        SERIAL_ECHOLNPGM("Did ", iteration + (iteration != z_auto_align_iterations), " of ", z_auto_align_iterations);
        SERIAL_ECHOLNPAIR_F("Accuracy: ", z_maxdiff);
      }

      // Stow the probe because the last call to probe.probe_at_point(...)
      // leaves the probe deployed when it's successful.
      IF_DISABLED(TOUCH_MI_PROBE, probe.stow());

      #if ENABLED(HOME_AFTER_G34)
        // After this operation the z position needs correction
        set_axis_never_homed(Z_AXIS);
        // Home Z after the alignment procedure
        process_subcommands_now(F("G28Z"));
      #else
        // Use the probed height from the last iteration to determine the Z height.
        // z_measured_min is used, because all steppers are aligned to z_measured_min.
        // Ideally, this would be equal to the 'z_probe * 0.5f' which was added earlier.
        current_position.z -= z_measured_min - (float)Z_CLEARANCE_BETWEEN_PROBES;
        sync_plan_position();
      #endif

      // Restore the active tool after homing
      TERN_(HAS_MULTI_HOTEND, tool_change(old_tool_index, DISABLED(PARKING_EXTRUDER))); // Fetch previous tool for parking extruder

      #if BOTH(HAS_LEVELING, RESTORE_LEVELING_AFTER_G34)
        set_bed_leveling_enabled(leveling_was_active);
      #endif

    }while(0);
  #endif // Z_STEPPER_AUTO_ALIGN
}

#endif // Z_MULTI_ENDSTOPS || Z_STEPPER_AUTO_ALIGN

#if ENABLED(Z_STEPPER_AUTO_ALIGN)

/**
 * M422: Set a Z-Stepper automatic alignment XY point.
 *       Use repeatedly to set multiple points.
 *
 *   S<index> : Index of the probe point to set
 *
 * With Z_STEPPER_ALIGN_STEPPER_XY:
 *   W<index> : Index of the Z stepper position to set
 *              The W and S parameters may not be combined.
 *
 * S and W require an X and/or Y parameter
 *   X<pos>   : X position to set (Unchanged if omitted)
 *   Y<pos>   : Y position to set (Unchanged if omitted)
 *
 * R : Recalculate points based on current probe offsets
 */
void GcodeSuite::M422() {

  if (!parser.seen_any()) return M422_report();

  if (parser.seen('R')) {
    z_stepper_align.reset_to_default();
    return;
  }

  const bool is_probe_point = parser.seen_test('S');

  if (TERN0(HAS_Z_STEPPER_ALIGN_STEPPER_XY, is_probe_point && parser.seen_test('W'))) {
    SERIAL_ECHOLNPGM("?(S) and (W) may not be combined.");
    return;
  }

  xy_pos_t * const pos_dest = (
    TERN_(HAS_Z_STEPPER_ALIGN_STEPPER_XY, !is_probe_point ? z_stepper_align.stepper_xy :)
    z_stepper_align.xy
  );

  if (!is_probe_point && TERN1(HAS_Z_STEPPER_ALIGN_STEPPER_XY, !parser.seen_test('W'))) {
    SERIAL_ECHOLNPGM("?(S)" TERN_(HAS_Z_STEPPER_ALIGN_STEPPER_XY, " or (W)") " is required.");
    return;
  }

  // Get the Probe Position Index or Z Stepper Index
  int8_t position_index = 1;
  FSTR_P err_string = F("?(S) Probe-position");
  if (is_probe_point)
    position_index = parser.intval('S');
  else {
    #if HAS_Z_STEPPER_ALIGN_STEPPER_XY
      err_string = F("?(W) Z-stepper");
      position_index = parser.intval('W');
    #endif
  }

  if (!WITHIN(position_index, 1, NUM_Z_STEPPERS)) {
    SERIAL_ECHOF(err_string);
    SERIAL_ECHOLNPGM(" index invalid (1.." STRINGIFY(NUM_Z_STEPPERS) ").");
    return;
  }

  --position_index;

  const xy_pos_t pos = {
    parser.floatval('X', pos_dest[position_index].x),
    parser.floatval('Y', pos_dest[position_index].y)
  };

  if (is_probe_point) {
    if (!probe.can_reach(pos.x, Y_CENTER)) {
      SERIAL_ECHOLNPGM("?(X) out of bounds.");
      return;
    }
    if (!probe.can_reach(pos)) {
      SERIAL_ECHOLNPGM("?(Y) out of bounds.");
      return;
    }
  }

  pos_dest[position_index] = pos;
}

void GcodeSuite::M422_report(const bool forReplay/*=true*/) {
  report_heading(forReplay, F(STR_Z_AUTO_ALIGN));
  LOOP_L_N(i, NUM_Z_STEPPERS) {
    report_echo_start(forReplay);
    SERIAL_ECHOLNPGM_P(
      PSTR("  M422 S"), i + 1,
      SP_X_STR, z_stepper_align.xy[i].x,
      SP_Y_STR, z_stepper_align.xy[i].y
    );
  }
  #if HAS_Z_STEPPER_ALIGN_STEPPER_XY
    LOOP_L_N(i, NUM_Z_STEPPERS) {
      report_echo_start(forReplay);
      SERIAL_ECHOLNPGM_P(
        PSTR("  M422 W"), i + 1,
        SP_X_STR, z_stepper_align.stepper_xy[i].x,
        SP_Y_STR, z_stepper_align.stepper_xy[i].y
      );
    }
  #endif
}

#endif // Z_STEPPER_AUTO_ALIGN