diff options
Diffstat (limited to 'resources/quality')
19 files changed, 19 insertions, 19 deletions
diff --git a/resources/quality/ultimaker3/um3_aa0.25_Nylon_Normal_Quality.inst.cfg b/resources/quality/ultimaker3/um3_aa0.25_Nylon_Normal_Quality.inst.cfg index 93f8d98598..7cb72ef3e0 100644 --- a/resources/quality/ultimaker3/um3_aa0.25_Nylon_Normal_Quality.inst.cfg +++ b/resources/quality/ultimaker3/um3_aa0.25_Nylon_Normal_Quality.inst.cfg @@ -17,7 +17,7 @@ cool_min_speed = 12 machine_nozzle_cool_down_speed = 0.9 machine_nozzle_heat_up_speed = 1.4 ooze_shield_angle = 40 -raft_airgap = =round(layer_height_0 * 0.85, 2) +raft_airgap = 0.15 retraction_min_travel = 5 skin_overlap = 50 speed_print = 70 diff --git a/resources/quality/ultimaker3/um3_aa0.4_Nylon_Draft_Print.inst.cfg b/resources/quality/ultimaker3/um3_aa0.4_Nylon_Draft_Print.inst.cfg index 34ff30d4e5..babf6f1306 100644 --- a/resources/quality/ultimaker3/um3_aa0.4_Nylon_Draft_Print.inst.cfg +++ b/resources/quality/ultimaker3/um3_aa0.4_Nylon_Draft_Print.inst.cfg @@ -19,7 +19,7 @@ material_print_temperature = =default_material_print_temperature + 10 material_initial_print_temperature = =material_print_temperature - 5 material_final_print_temperature = =material_print_temperature - 10 ooze_shield_angle = 40 -raft_airgap = =round(layer_height_0 * 0.85, 2) +raft_airgap = 0.25 skin_overlap = 50 speed_layer_0 = =math.ceil(speed_print * 20 / 70) switch_extruder_prime_speed = 30 diff --git a/resources/quality/ultimaker3/um3_aa0.4_Nylon_Fast_Print.inst.cfg b/resources/quality/ultimaker3/um3_aa0.4_Nylon_Fast_Print.inst.cfg index 36c0dbbf2f..cbf61a838f 100644 --- a/resources/quality/ultimaker3/um3_aa0.4_Nylon_Fast_Print.inst.cfg +++ b/resources/quality/ultimaker3/um3_aa0.4_Nylon_Fast_Print.inst.cfg @@ -19,7 +19,7 @@ material_print_temperature = =default_material_print_temperature + 5 material_initial_print_temperature = =material_print_temperature - 5 material_final_print_temperature = =material_print_temperature - 10 ooze_shield_angle = 40 -raft_airgap = =round(layer_height_0 * 0.85, 2) +raft_airgap = 0.25 skin_overlap = 50 speed_layer_0 = =math.ceil(speed_print * 20 / 70) switch_extruder_prime_speed = 30 diff --git a/resources/quality/ultimaker3/um3_aa0.4_Nylon_High_Quality.inst.cfg b/resources/quality/ultimaker3/um3_aa0.4_Nylon_High_Quality.inst.cfg index 9bc7c2ecce..31e1d559f3 100644 --- a/resources/quality/ultimaker3/um3_aa0.4_Nylon_High_Quality.inst.cfg +++ b/resources/quality/ultimaker3/um3_aa0.4_Nylon_High_Quality.inst.cfg @@ -18,7 +18,7 @@ cool_min_speed = 15 material_initial_print_temperature = =material_print_temperature - 5 material_final_print_temperature = =material_print_temperature - 10 ooze_shield_angle = 40 -raft_airgap = =round(layer_height_0 * 0.85, 2) +raft_airgap = 0.25 skin_overlap = 50 speed_layer_0 = =math.ceil(speed_print * 20 / 70) switch_extruder_prime_speed = 30 diff --git a/resources/quality/ultimaker3/um3_aa0.4_Nylon_Normal_Quality.inst.cfg b/resources/quality/ultimaker3/um3_aa0.4_Nylon_Normal_Quality.inst.cfg index c5f92c2515..761ab7d56d 100644 --- a/resources/quality/ultimaker3/um3_aa0.4_Nylon_Normal_Quality.inst.cfg +++ b/resources/quality/ultimaker3/um3_aa0.4_Nylon_Normal_Quality.inst.cfg @@ -18,7 +18,7 @@ cool_min_speed = 12 material_initial_print_temperature = =material_print_temperature - 5 material_final_print_temperature = =material_print_temperature - 10 ooze_shield_angle = 40 -raft_airgap = =round(layer_height_0 * 0.85, 2) +raft_airgap = 0.25 skin_overlap = 50 speed_layer_0 = =math.ceil(speed_print * 20 / 70) switch_extruder_prime_speed = 30 diff --git a/resources/quality/ultimaker3/um3_aa0.8_Nylon_Draft_Print.inst.cfg b/resources/quality/ultimaker3/um3_aa0.8_Nylon_Draft_Print.inst.cfg index aa9d44f0e0..a171427548 100644 --- a/resources/quality/ultimaker3/um3_aa0.8_Nylon_Draft_Print.inst.cfg +++ b/resources/quality/ultimaker3/um3_aa0.8_Nylon_Draft_Print.inst.cfg @@ -19,7 +19,7 @@ machine_nozzle_cool_down_speed = 0.9 machine_nozzle_heat_up_speed = 1.4 ooze_shield_angle = 40 prime_tower_enable = True -raft_airgap = =round(layer_height_0 * 0.85, 2) +raft_airgap = 0.45 support_angle = 70 switch_extruder_prime_speed = 30 switch_extruder_retraction_amount = 30 diff --git a/resources/quality/ultimaker3/um3_aa0.8_Nylon_Superdraft_Print.inst.cfg b/resources/quality/ultimaker3/um3_aa0.8_Nylon_Superdraft_Print.inst.cfg index 56432e5af9..e80a6c73fd 100644 --- a/resources/quality/ultimaker3/um3_aa0.8_Nylon_Superdraft_Print.inst.cfg +++ b/resources/quality/ultimaker3/um3_aa0.8_Nylon_Superdraft_Print.inst.cfg @@ -20,7 +20,7 @@ machine_nozzle_cool_down_speed = 0.9 machine_nozzle_heat_up_speed = 1.4 ooze_shield_angle = 40 prime_tower_enable = True -raft_airgap = =round(layer_height_0 * 0.85, 2) +raft_airgap = 0.45 support_angle = 70 switch_extruder_prime_speed = 30 switch_extruder_retraction_amount = 30 diff --git a/resources/quality/ultimaker3/um3_aa0.8_Nylon_Verydraft_Print.inst.cfg b/resources/quality/ultimaker3/um3_aa0.8_Nylon_Verydraft_Print.inst.cfg index 6e98944441..a2ca3a769f 100644 --- a/resources/quality/ultimaker3/um3_aa0.8_Nylon_Verydraft_Print.inst.cfg +++ b/resources/quality/ultimaker3/um3_aa0.8_Nylon_Verydraft_Print.inst.cfg @@ -20,7 +20,7 @@ machine_nozzle_cool_down_speed = 0.9 machine_nozzle_heat_up_speed = 1.4 ooze_shield_angle = 40 prime_tower_enable = True -raft_airgap = =round(layer_height_0 * 0.85, 2) +raft_airgap = 0.45 support_angle = 70 switch_extruder_prime_speed = 30 switch_extruder_retraction_amount = 30 diff --git a/resources/quality/ultimaker_s3/um_s3_aa0.4_PLA_VeryDraft_Print.inst.cfg b/resources/quality/ultimaker_s3/um_s3_aa0.4_PLA_VeryDraft_Print.inst.cfg index 2b12e3380b..d20c1303b8 100644 --- a/resources/quality/ultimaker_s3/um_s3_aa0.4_PLA_VeryDraft_Print.inst.cfg +++ b/resources/quality/ultimaker_s3/um_s3_aa0.4_PLA_VeryDraft_Print.inst.cfg @@ -34,5 +34,5 @@ top_bottom_thickness = 0.9 infill_pattern = ='zigzag' if infill_sparse_density > 80 else 'triangles' -raft_airgap = =0.25 +raft_airgap = 0.25 wall_line_width_0 = =line_width * (1 + magic_spiralize * 0.25)
\ No newline at end of file diff --git a/resources/quality/ultimaker_s3/um_s3_aa0.4_TPLA_VeryDraft_Print.inst.cfg b/resources/quality/ultimaker_s3/um_s3_aa0.4_TPLA_VeryDraft_Print.inst.cfg index 1b508e3a23..2d05a15f3c 100644 --- a/resources/quality/ultimaker_s3/um_s3_aa0.4_TPLA_VeryDraft_Print.inst.cfg +++ b/resources/quality/ultimaker_s3/um_s3_aa0.4_TPLA_VeryDraft_Print.inst.cfg @@ -34,5 +34,5 @@ top_bottom_thickness = 1.2 infill_pattern = ='zigzag' if infill_sparse_density > 80 else 'triangles' -raft_airgap = =0.25 +raft_airgap = 0.25 wall_line_width_0 = =line_width * (1 + magic_spiralize * 0.25)
\ No newline at end of file diff --git a/resources/quality/ultimaker_s3/um_s3_aa0.8_Nylon_Draft_Print.inst.cfg b/resources/quality/ultimaker_s3/um_s3_aa0.8_Nylon_Draft_Print.inst.cfg index deed7d6486..09de59ba20 100644 --- a/resources/quality/ultimaker_s3/um_s3_aa0.8_Nylon_Draft_Print.inst.cfg +++ b/resources/quality/ultimaker_s3/um_s3_aa0.8_Nylon_Draft_Print.inst.cfg @@ -21,7 +21,7 @@ machine_nozzle_cool_down_speed = 0.9 machine_nozzle_heat_up_speed = 1.4 ooze_shield_angle = 40 prime_tower_enable = True -raft_airgap = =round(layer_height_0 * 0.85, 2) +raft_airgap = 0.45 support_angle = 70 switch_extruder_prime_speed = 30 switch_extruder_retraction_amount = 30 diff --git a/resources/quality/ultimaker_s3/um_s3_aa0.8_Nylon_Superdraft_Print.inst.cfg b/resources/quality/ultimaker_s3/um_s3_aa0.8_Nylon_Superdraft_Print.inst.cfg index 5dfbf6ce6c..d6e11ca953 100644 --- a/resources/quality/ultimaker_s3/um_s3_aa0.8_Nylon_Superdraft_Print.inst.cfg +++ b/resources/quality/ultimaker_s3/um_s3_aa0.8_Nylon_Superdraft_Print.inst.cfg @@ -21,7 +21,7 @@ machine_nozzle_cool_down_speed = 0.9 machine_nozzle_heat_up_speed = 1.4 ooze_shield_angle = 40 prime_tower_enable = True -raft_airgap = =round(layer_height_0 * 0.85, 2) +raft_airgap = 0.45 support_angle = 70 switch_extruder_prime_speed = 30 switch_extruder_retraction_amount = 30 diff --git a/resources/quality/ultimaker_s3/um_s3_aa0.8_Nylon_Verydraft_Print.inst.cfg b/resources/quality/ultimaker_s3/um_s3_aa0.8_Nylon_Verydraft_Print.inst.cfg index 2717be119c..599789f528 100644 --- a/resources/quality/ultimaker_s3/um_s3_aa0.8_Nylon_Verydraft_Print.inst.cfg +++ b/resources/quality/ultimaker_s3/um_s3_aa0.8_Nylon_Verydraft_Print.inst.cfg @@ -21,7 +21,7 @@ machine_nozzle_cool_down_speed = 0.9 machine_nozzle_heat_up_speed = 1.4 ooze_shield_angle = 40 prime_tower_enable = True -raft_airgap = =round(layer_height_0 * 0.85, 2) +raft_airgap = 0.45 support_angle = 70 switch_extruder_prime_speed = 30 switch_extruder_retraction_amount = 30 diff --git a/resources/quality/ultimaker_s5/um_s5_aa0.25_Nylon_Normal_Quality.inst.cfg b/resources/quality/ultimaker_s5/um_s5_aa0.25_Nylon_Normal_Quality.inst.cfg index 5e4bfd359d..b06a514334 100644 --- a/resources/quality/ultimaker_s5/um_s5_aa0.25_Nylon_Normal_Quality.inst.cfg +++ b/resources/quality/ultimaker_s5/um_s5_aa0.25_Nylon_Normal_Quality.inst.cfg @@ -18,7 +18,7 @@ cool_min_speed = 12 machine_nozzle_cool_down_speed = 0.9 machine_nozzle_heat_up_speed = 1.4 ooze_shield_angle = 40 -raft_airgap = =round(layer_height_0 * 0.85, 2) +raft_airgap = 0.15 retraction_min_travel = 5 skin_overlap = 50 speed_print = 70 diff --git a/resources/quality/ultimaker_s5/um_s5_aa0.4_PLA_VeryDraft_Print.inst.cfg b/resources/quality/ultimaker_s5/um_s5_aa0.4_PLA_VeryDraft_Print.inst.cfg index 3b20559564..962f906e74 100644 --- a/resources/quality/ultimaker_s5/um_s5_aa0.4_PLA_VeryDraft_Print.inst.cfg +++ b/resources/quality/ultimaker_s5/um_s5_aa0.4_PLA_VeryDraft_Print.inst.cfg @@ -35,5 +35,5 @@ top_bottom_thickness = 0.9 infill_pattern = ='zigzag' if infill_sparse_density > 80 else 'triangles' -raft_airgap = =0.25 +raft_airgap = 0.25 wall_line_width_0 = =line_width * (1 + magic_spiralize * 0.25)
\ No newline at end of file diff --git a/resources/quality/ultimaker_s5/um_s5_aa0.4_TPLA_VeryDraft_Print.inst.cfg b/resources/quality/ultimaker_s5/um_s5_aa0.4_TPLA_VeryDraft_Print.inst.cfg index bfb76f20c8..5150537256 100644 --- a/resources/quality/ultimaker_s5/um_s5_aa0.4_TPLA_VeryDraft_Print.inst.cfg +++ b/resources/quality/ultimaker_s5/um_s5_aa0.4_TPLA_VeryDraft_Print.inst.cfg @@ -34,5 +34,5 @@ top_bottom_thickness = 1.2 infill_pattern = ='zigzag' if infill_sparse_density > 80 else 'triangles' -raft_airgap = =0.25 +raft_airgap = 0.25 wall_line_width_0 = =line_width * (1 + magic_spiralize * 0.25)
\ No newline at end of file diff --git a/resources/quality/ultimaker_s5/um_s5_aa0.8_Nylon_Draft_Print.inst.cfg b/resources/quality/ultimaker_s5/um_s5_aa0.8_Nylon_Draft_Print.inst.cfg index 7bd2536fa0..addfe52641 100644 --- a/resources/quality/ultimaker_s5/um_s5_aa0.8_Nylon_Draft_Print.inst.cfg +++ b/resources/quality/ultimaker_s5/um_s5_aa0.8_Nylon_Draft_Print.inst.cfg @@ -19,7 +19,7 @@ machine_nozzle_cool_down_speed = 0.9 machine_nozzle_heat_up_speed = 1.4 ooze_shield_angle = 40 prime_tower_enable = True -raft_airgap = =round(layer_height_0 * 0.85, 2) +raft_airgap = 0.45 support_angle = 70 switch_extruder_prime_speed = 30 switch_extruder_retraction_amount = 30 diff --git a/resources/quality/ultimaker_s5/um_s5_aa0.8_Nylon_Superdraft_Print.inst.cfg b/resources/quality/ultimaker_s5/um_s5_aa0.8_Nylon_Superdraft_Print.inst.cfg index 4ba546ab06..aec980aa48 100644 --- a/resources/quality/ultimaker_s5/um_s5_aa0.8_Nylon_Superdraft_Print.inst.cfg +++ b/resources/quality/ultimaker_s5/um_s5_aa0.8_Nylon_Superdraft_Print.inst.cfg @@ -19,7 +19,7 @@ machine_nozzle_cool_down_speed = 0.9 machine_nozzle_heat_up_speed = 1.4 ooze_shield_angle = 40 prime_tower_enable = True -raft_airgap = =round(layer_height_0 * 0.85, 2) +raft_airgap = 0.45 support_angle = 70 switch_extruder_prime_speed = 30 switch_extruder_retraction_amount = 30 diff --git a/resources/quality/ultimaker_s5/um_s5_aa0.8_Nylon_Verydraft_Print.inst.cfg b/resources/quality/ultimaker_s5/um_s5_aa0.8_Nylon_Verydraft_Print.inst.cfg index 5466fb4a72..fc9d586503 100644 --- a/resources/quality/ultimaker_s5/um_s5_aa0.8_Nylon_Verydraft_Print.inst.cfg +++ b/resources/quality/ultimaker_s5/um_s5_aa0.8_Nylon_Verydraft_Print.inst.cfg @@ -21,7 +21,7 @@ machine_nozzle_cool_down_speed = 0.9 machine_nozzle_heat_up_speed = 1.4 ooze_shield_angle = 40 prime_tower_enable = True -raft_airgap = =round(layer_height_0 * 0.85, 2) +raft_airgap = 0.45 support_angle = 70 switch_extruder_prime_speed = 30 switch_extruder_retraction_amount = 30 |