1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
|
// AZSMZ holder.
$fn=360/12;
include <configuration.scad>;
include <roundedBox.scad>;
// All measurements in mm.
debug = false;
xSize = 103.75;
ySize = 68.0;
zSize = 3;
zPcBoard = 1.5;
yPcBoardOffset = 10;
pillarHeight = 7 - zPcBoard;
yTabOffset = 2.5;
edgeWidth = 15;
outsideEdge = 5;
radius = 5;
sdOffset = 39;
sdWidth = 14;
sdOpeningWidth = 50;
// AZSMZ holes.
upperLeft = [ 3.5, ySize-3.25];
upperRight = [xSize-3.5, ySize-3.25];
lowerLeft = [ 12.8, 3.75];
lowerRight = [xSize-3.5, 3.75];
module azsmzPlate()
{
difference()
{
if (debug)
{
// Show the AZSMZ board.
translate([0, yPcBoardOffset, pillarHeight])
%cube([xSize, ySize, zPcBoard]);
translate([sdOffset, yPcBoardOffset-5, pillarHeight])
%cube([sdWidth, 5, zPcBoard]);
}
union()
{
// Make the body.
translate([xSize/2, yPcBoardOffset+ySize/2, zSize/2])
roundedBox([xSize+outsideEdge,
ySize+outsideEdge,
zSize],
radius, true);
// Add extra material for filleting the corners between the tabs
// and body.
// Left:
translate([-radius-outsideEdge/2, extrusionWidth-yTabOffset, 0])
cube([radius, radius, zSize+smidge]);
// Right:
translate([xSize+radius-outsideEdge/2,
extrusionWidth-yTabOffset,
0])
cube([radius, radius, zSize+smidge]);
// Add two tabs for M5x8 screws to attach to the aluminum
// extrusions.
translate([xSize/2, extrusionWidth/2-yTabOffset, zSize/2])
roundedBox([xSize+2*extrusionWidth,
extrusionWidth,
zSize],
radius, true);
// Add four pillars to elevate the AZSMZ slightly.
addPillar(upperLeft);
addPillar(upperRight);
addPillar(lowerLeft);
addPillar(lowerRight);
}
// Make two M5x8 screw holes in the two tabs.
translate([-extrusionWidth/2, extrusionWidth/2-yTabOffset, 0])
m5x8();
translate([xSize+extrusionWidth/2, extrusionWidth/2-yTabOffset, 0])
m5x8();
// Remove a cutout in the center.
translate([xSize/2, yPcBoardOffset+ySize/2, zSize/2])
roundedBox([xSize-edgeWidth,
ySize-edgeWidth,
zSize+smidge],
radius, true);
// Remove a cutout to make it easier to remove the SD card.
translate([sdOffset+sdWidth/2, 0, zSize/2])
roundedBox([sdOpeningWidth, 20, zSize+smidge], radius, true);
// Round the left inside corner by the cutout for the SD card.
difference()
{
translate([sdOffset+sdWidth/2-radius-sdOpeningWidth/2,
-yTabOffset-smidge/2,
-smidge/2])
cube([radius+smidge, radius+smidge, zSize+smidge]);
translate([sdOffset+sdWidth/2-radius-sdOpeningWidth/2,
yTabOffset,
0])
cylinder(r=radius, h=zSize+2*smidge);
}
// Round the right inside corner by the cutout for the SD card.
difference()
{
translate([sdOffset+sdWidth/2+sdOpeningWidth/2-smidge/2,
-yTabOffset-smidge/2,
-smidge/2])
cube([radius+smidge, radius+smidge, zSize+smidge]);
translate([sdOffset+sdWidth/2+radius+sdOpeningWidth/2,
yTabOffset,
0])
cylinder(r=radius, h=zSize+2*smidge);
}
// Round the outside corners between the tabs and body.
// Left:
translate([-radius-outsideEdge/2,
radius+extrusionWidth-yTabOffset,
-smidge/2])
cylinder(r=radius, h=zSize+2*smidge);
// Right:
translate([xSize+2*radius-outsideEdge/2,
radius+extrusionWidth-yTabOffset,
-smidge/2])
cylinder(r=radius, h=zSize+2*smidge);
// Make four M3x6 screw holes in the four pillars.
m3x6(upperLeft);
m3x6(upperRight);
m3x6(lowerLeft);
m3x6(lowerRight);
}
}
module addPillar(pos)
{
translate([pos[0], pos[1]+yPcBoardOffset, 0])
cylinder(r=m3LooseHeadRadius, h=pillarHeight);
}
module m3x6(pos)
{
// These holes need to be slightly tight.
translate([pos[0], pos[1]+yPcBoardOffset, -smidge/2])
cylinder(r1=m3Radius-smidge, r2=m3LooseRadius, h=pillarHeight+smidge);
}
module m5x8()
{
// These holes should be loose.
translate([0, 0, -smidge/2])
cylinder(r=m5LooseRadius, h=pillarHeight+smidge);
}
azsmzPlate();
|
