1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
|
// Fuse/plug holder.
//
// This is my favorite lit switch, it includes the fuse and is the least
// expensive:
//
// http://www.robotdigg.com/product/744/AC-rocker-switch-power-inlet-socket-w/-fuse
//
//
// It also works with this lit switch from Amazon:
//
// http://www.amazon.com/uxcell%C2%AE-IEC320-Inlet-Switch-Socket/dp/B00N41D5Z4
//
// uxcell 2 Pcs IEC320 C14 Inlet Green Lamp Switch Power Socket AC 250V
//
//
// Or this one:
//
// http://www.amazon.com/gp/product/B00ME5YAPK/ref=oh_aui_detailpage_o03_s01
//
// URBEST Inlet Module Plug Fuse Switch Male Power Socket 10A 250V 3 Pin
// IEC320 C14
//
//
// Note: the above two switches do *not* include the fuse!
//
// Here are the fuses:
//
// http://www.amazon.com/PODOY-Qty-Fast-Blow-GMA10A-GMA10/dp/B004HLYUE0
//
// PODOY 5 Qty. GMA 10A Fast-Blow Fuse 10 Amp 250v GMA10A, GMA10
$fn=360/12;
include <configuration.scad>
include <roundedBox.scad>;
// All measurements in mm.
xBody = 70;
yBody = lowerFrameHeight;
zBody = 3;
zTube = 30;
xOpening = 47+2;
yOpening = 27+1;
mountingHoleSeparation = 40;
module fusePlugHolder()
{
translate([0, 0, zBody/2])
difference()
{
union()
{
// Make the body.
roundedBox([xBody,
yBody,
zBody], 5, true);
translate([0, 0, zTube/2])
roundedBox([xOpening+3,
yOpening+3,
zBody+zTube], 4, true);
}
// Remove the center, where the fuse/plug holder slides in.
translate([0, 0, zTube/2])
roundedBox([xOpening,
yOpening,
zBody+zTube+smidge], 3, true);
// Remove two holes to use for mounting the fuse/plug holder.
makeTightHole(0, mountingHoleSeparation/2);
makeTightHole(0, -mountingHoleSeparation/2);
// Remove four M5x8 holes for mounting
m5x8Slot( xBody/2-extrusionWidth/2, yBody/2 - extrusionWidth/2);
m5x8Slot(-xBody/2+extrusionWidth/2, yBody/2 - extrusionWidth/2);
m5x8Slot( xBody/2-extrusionWidth/2, -yBody/2 + extrusionWidth/2);
m5x8Slot(-xBody/2+extrusionWidth/2, -yBody/2 + extrusionWidth/2);
}
}
module m5x8Slot(x, y)
{
offset = 1.0;
hull()
{
translate([x, y, 0])
cylinder(r=m5LooseRadius, h=zBody+smidge, center=true);
if (y < 0)
translate([x, y+offset, 0])
cylinder(r=m5LooseRadius, h=zBody+smidge, center=true);
if (y > 0)
translate([x, y-offset, 0])
cylinder(r=m5LooseRadius, h=zBody+smidge, center=true);
}
}
module makeTightHole(x, y)
{
translate([x, y, 0])
cylinder(r=m3Radius-smidge, h=zBody+smidge, center=true);
}
fusePlugHolder();
|
