1 files changed, 237 insertions, 0 deletions
diff --git a/src/avrdude/ChangeLog-2002 b/src/avrdude/ChangeLog-2002
new file mode 100644
index 000000000..9bfa030a9
--- /dev/null
+++ b/src/avrdude/ChangeLog-2002
@@ -0,0 +1,237 @@
+2002-12-12  Brian S. Dean  <bsd@bsdhome.com>
+
+	* main.c: minor cleanup
+
+2002-12-07  Brian S. Dean  <bsd@bsdhome.com>
+
+	* avrdude.1, main.c:
+	If the stk500 is being used, default to using the first serial port.
+
+2002-12-03  Brian S. Dean  <bsd@bsdhome.com>
+
+	* avrdude.1: Mention STK500 support.
+
+2002-12-01  Brian S. Dean  <bsd@bsdhome.com>
+
+	* stk500.c: Remove unused code.
+
+	* CHANGELOG, stk500.c:
+	Document changes since the previous version in the CHANGELOG.
+
+	Cleanup stk500.c a bit.
+
+	* stk500.c: Fix cut and paste braino.
+
+	* avr.c, avrdude.conf.sample, main.c, pgm.h, stk500.c:
+	The STK500 can perform paged read/write operations even on standard
+	"non-paged" parts.  Take advantage of that and use the faster internal
+	routines of the STK500 for those parts as well.
+
+	* avr.c, avr.h, avrpart.h, main.c, pgm.c, pgm.h, stk500.c:
+	Optimize reading and writing for the STK500 programmer if the part
+	supports paged reads and writes.  This greatly decreases the
+	program/verify time from about 4.5 minutes down to about 10 seconds in
+	a 12K program size test case.
+
+	Print out the hardware and firmware version for the STK500 if verbose
+	is enabled.
+
+	* avrdude.conf.sample, avrpart.h, config_gram.y, lexer.l, pgm.h:
+	* ppi.c, ppi.h, stk500.c, stk500.h, stk500_private.h:
+	Add basic support for STK500.
+
+2002-11-30  Brian S. Dean  <bsd@bsdhome.com>
+
+	* avrdude.conf.sample, config.c, config.h, config_gram.y, lexer.l:
+	* main.c, pgm.c, pgm.h, ppi.c, ppi.h, term.c, term.h, Makefile:
+	* avr.c, avr.h:
+	Seperate programmer operations out into a driver-like interface so
+	that programmers other than the direct parallel port connection can be
+	supported.
+
+2002-11-23  Brian S. Dean  <bsd@bsdhome.com>
+
+	* CHANGELOG, main.c, term.c:
+	term.c - when in interactive terminal mode and dumping memory using
+	         the 'dump <memtype>' command without any address information,
+	         and the end of memory is reached, wrap back around to zero on
+	         the next invocation.
+
+	CHANGELOG - describe changes
+
+	main.c - update version number
+
+	* main.c:
+	When getting ready to initiate communications with the AVR device,
+	first pull /RESET low for a short period of time before enabling the
+	buffer chip.  This sequence allows the AVR to be reset before the
+	buffer is enabled to avoid a short period of time where the AVR may be
+	driving the programming lines at the same time the programmer tries
+	to.  Of course, if a buffer is being used, then the /RESET line from
+	the programmer needs to be directly connected to the AVR /RESET line
+	and not via the buffer chip.
+
+2002-11-06  Brian S. Dean  <bsd@bsdhome.com>
+
+	* CHANGELOG: Update changelog.
+
+	* avr.c, avr.h, main.c: Fix -Y option.  Reported by Joerg Wunsch.
+
+2002-11-01  Brian S. Dean  <bsd@bsdhome.com>
+
+	* CHANGELOG, main.c: Version update and CHANGELOG entry.
+
+	* avr.c:
+	Be backward compatible with the 2-byte rewrite cycle counter which
+	appeared in version 2.1.0, but was changed to a 4 byte counter in
+	version 2.1.1.  Reminded by Joerg Wunsch.
+
+2002-10-29  Brian S. Dean  <bsd@bsdhome.com>
+
+	* CHANGELOG, avrdude.1, main.c:
+	Add '-V' (no verify) flag requested by Joerg Wunsch.  Update the man
+	page.
+
+2002-10-13  Brian S. Dean  <bsd@bsdhome.com>
+
+	* CHANGELOG, avrdude.1: Update man page and changelog.
+
+	* main.c: Update version number.
+
+2002-10-12  Brian S. Dean  <bsd@bsdhome.com>
+
+	* Makefile: Remove --pedantic and -g from the compiler options.
+
+2002-10-11  Brian S. Dean  <bsd@bsdhome.com>
+
+	* avr.c, term.c:
+	Use a four byte value instead of a two byte value for the programming
+	cycle count stored at the end of EEPROM.  It seems as though Atmel was
+	greatly conservative in claiming a 1000 count reliability for the
+	FLASH.  I current have a part that has been reprogrammed 173330 times,
+	and counting.
+
+	Fix a compiler warning.
+
+	* avrdude.conf.sample:
+	Fix ATMega128 instruction encoding for reading the low and high fuse
+	bits.  Thanks to Joerg Wunsch for tripping over this.
+
+2002-08-01  Brian S. Dean  <bsd@bsdhome.com>
+
+	* avr.c, avrdude.1, main.c:
+	Move erase-rewrite cycle increment to within the chip erase routine so
+	that it is tracked no matter where the erase was initiated: command
+	line mode or interactive mode, without code duplicaiton.
+
+	* CHANGELOG: Recent updates.
+
+	* avr.c: Eliminate unused variables.
+
+	* avr.c, avr.h, avrdude.1, fileio.c, main.c:
+	Implement a way of tracking how many erase-rewrite cycles a part has
+	undergone.  This utilizes the last two bytes of EEPROM to maintain a
+	counter that is incremented each time the part is erased.
+
+2002-07-27  Brian S. Dean  <bsd@bsdhome.com>
+
+	* avr.c, main.c:
+	Fix a typo in a comment.  Display the size of memory being written.
+	Display the correct memory name in an error message (previously
+	hardcoded).
+
+2002-06-22  Brian S. Dean  <bsd@bsdhome.com>
+
+	* CHANGELOG, avrdude.conf.sample:
+	Add support for ATtiny15 - contributed by Asher Hoskins
+	<asher@crumbly.freeserve.co.uk>
+
+2002-04-23  Brian S. Dean  <bsd@bsdhome.com>
+
+	* CHANGELOG: Say what changed.
+
+2002-04-07  Brian S. Dean  <bsd@bsdhome.com>
+
+	* Makefile, avrdude.conf.sample:
+	Backup the config file to a timestamped name to keep from possibly
+	overwriting user-modified configs.
+
+	Add read/write instructions for all memory types for ATMEGA103,
+	ATMEGA128, ATMEGA16, and ATMEGA8.
+
+2002-04-05  Brian S. Dean  <bsd@bsdhome.com>
+
+	* avrdude.conf.sample:
+	Add support for ATMEGA128; untested; requested by Jeff Gardner
+	<gardner@journey.com>.
+
+2002-02-15  Brian S. Dean  <bsd@bsdhome.com>
+
+	* avrdude.conf.sample: Minor ordering.
+
+	* CHANGELOG, main.c: Update version numbers.
+
+2002-02-14  Brian S. Dean  <bsd@bsdhome.com>
+
+	* CHANGELOG: Summarize latest updates.
+
+	* avrdude.conf.sample, config_gram.y:
+	Make pwroff_after_write a yes/no field instead of a numeric.
+
+	* avrdude.conf.sample: Document the pwroff_after_write flag.
+
+	* avr.c: Enable the extra part verbosity when verbosity >= 3.
+
+	* avr.c, avr.h, avrdude.conf.sample, config_gram.y, lexer.l:
+	* main.c, term.c:
+	Fix error reporting by avr_write_byte().
+
+	Fix setting of status LEDs under various write-fail conditions.
+
+	Add a flag to indicate that a memory type requires the device to
+	possibly be powered off and back on after a write to it.  This is due
+	to a hardware problem on some Atmel devices, see:
+
+		http://www.atmel.com/atmel/acrobat/doc1280.pdf
+
+	Add greater verbosity to the part-display code when verbose>1 to
+	display avrprog's encoding of the defined programming instructions.
+	This is primarily for debugging purposes.
+
+
+	Part updates:
+
+	  * add the AT90S4414 part
+
+	  * add fuse and lock bit access instructions for the AT90S1200,
+	    AT90S4434, and AT90S8515.
+
+	  * add the pwroff_after_write flag to the fuse bits for the AT90S2333
+	    and AT90S4433 parts
+
+2002-02-09  Brian S. Dean  <bsd@bsdhome.com>
+
+	* avrdude.conf.sample:
+	Updates to the 2333 and 4433 parts, contributed by Joerg Wunsh.
+
+2002-01-18  Brian S. Dean  <bsd@bsdhome.com>
+
+	* CHANGELOG: Add changelog.
+
+2002-01-12  Brian S. Dean  <bsd@bsdhome.com>
+
+	* main.c: Add (c) to copyright.
+
+	* fileio.c, fileio.h, lexer.l, lists.c, lists.h, main.c:
+	* pindefs.h, ppi.c, ppi.h, term.c, term.h, avr.c, avr.h:
+	* config.c, config.h, config_gram.y:
+	Update version number.  Update copyright.
+
+	* avrdude.1: Update copyright and add description of "default".
+
+	Submitted by: Joerg Wunsch <j@uriah.heep.sax.de>
+
+	* avr.c, term.c:
+	Fix programming of write-only memories (such as lock bits on the
+	2313).
+