diff options
Diffstat (limited to 'Meltingplot.ini')
| -rw-r--r-- | Meltingplot.ini | 632 |
1 files changed, 632 insertions, 0 deletions
diff --git a/Meltingplot.ini b/Meltingplot.ini new file mode 100644 index 0000000..edc6f10 --- /dev/null +++ b/Meltingplot.ini @@ -0,0 +1,632 @@ +# Print profiles for the Meltingplot printers. + +[vendor] +# Vendor name will be shown by the Config Wizard. +name = Meltingplot +# Configuration version of this file. Config file will only be installed, if the config_version differs. +# This means, the server may force the PrusaSlicer configuration to be downgraded. +config_version = 0.0.7 +# Where to get the updates from? +config_update_url = +changelog_url = + +# The printer models will be shown by the Configuration Wizard in this order, +# also the first model installed & the first nozzle installed will be activated after install. +#TODO: One day we may differentiate variants of the nozzles / hot ends, +#for example by the melt zone size, or whether the nozzle is hardened. +# Printer model name will be shown by the installation wizard. + +[print:*common*] +avoid_crossing_perimeters = 0 +bottom_fill_pattern = rectilinear +bottom_solid_layers = 3 +bottom_solid_min_thickness = 0.6 +bridge_acceleration = 0 +bridge_angle = 0 +bridge_flow_ratio = 1.0 +bridge_speed = 42 +brim_width = 0 +clip_multipart_objects = 1 +compatible_printers = +compatible_printers_condition = nozzle_diameter[0]==0.8 +complete_objects = 0 +default_acceleration = 0 +dont_support_bridges = 1 +draft_shield = 0 +elefant_foot_compensation = 0.1 +ensure_vertical_shell_thickness = 1 +external_perimeter_extrusion_width = 115% +external_perimeter_speed = 25% +external_perimeters_first = 0 +extra_perimeters = 1 +extruder_clearance_height = 30 +extruder_clearance_radius = 75 +extrusion_width = 0 +fill_angle = 45 +fill_density = 20% +fill_pattern = cubic +first_layer_acceleration = 0 +first_layer_extrusion_width = 120% +first_layer_height = 0.5 +first_layer_speed = 20 +gap_fill_speed = 42 +gcode_comments = 0 +gcode_label_objects = 1 +infill_acceleration = 0 +infill_every_layers = 1 +infill_extruder = 1 +infill_extrusion_width = 115% +infill_first = 0 +infill_only_where_needed = 0 +infill_overlap = 20% +infill_speed = 80 +interface_shells = 0 +max_print_speed = 200 +max_volumetric_speed = 28 +min_skirt_length = 0 +notes = +only_retract_when_crossing_perimeters = 0 +ooze_prevention = 0 +output_filename_format = {input_filename_base}_{layer_height}mm_{filament_type[0]}_{printer_model}_{print_time}.gcode +overhangs = 1 +perimeter_acceleration = 0 +perimeter_extruder = 1 +perimeter_extrusion_width = 120% +perimeter_speed = 80 +perimeters = 2 +post_process = +print_settings_id = +raft_layers = 0 +resolution = 0 +seam_position = aligned +single_extruder_multi_material_priming = 1 +skirt_distance = 5 +skirt_height = 1 +skirts = 3 +small_perimeter_speed = 42 +solid_infill_below_area = 0 +solid_infill_every_layers = 0 +solid_infill_extruder = 1 +solid_infill_extrusion_width = 120% +solid_infill_speed = 100% +spiral_vase = 0 +standby_temperature_delta = -5 +support_material = 0 +support_material_angle = 0 +support_material_auto = 1 +support_material_buildplate_only = 1 +support_material_contact_distance = 0.2 +support_material_enforce_layers = 0 +support_material_extruder = 1 +support_material_extrusion_width = 100% +support_material_interface_contact_loops = 0 +support_material_interface_extruder = 1 +support_material_interface_layers = 4 +support_material_interface_spacing = 0.2 +support_material_interface_speed = 80% +support_material_pattern = rectilinear +support_material_spacing = 2.5 +support_material_speed = 50 +support_material_synchronize_layers = 0 +support_material_threshold = 55 +support_material_with_sheath = 1 +support_material_xy_spacing = 75% +thin_walls = 1 +top_fill_pattern = monotonic +top_infill_extrusion_width = 105% +top_solid_infill_speed = 50 +top_solid_layers = 4 +top_solid_min_thickness = 0.8 +travel_speed = 160 +wipe_tower = 0 +wipe_tower_bridging = 10 +wipe_tower_no_sparse_layers = 0 +wipe_tower_rotation_angle = 0 +wipe_tower_width = 60 +wipe_tower_x = 180 +wipe_tower_y = 140 +xy_size_compensation = 0 +extrusion_spacing = +perimeter_extrusion_spacing = +external_perimeter_extrusion_spacing = +first_layer_extrusion_spacing = +infill_extrusion_spacing = +solid_infill_extrusion_spacing = +top_infill_extrusion_spacing = + +[print:*MBL*] +travel_speed = 250 +standby_temperature_delta = -5 + +[print:*0.20mm*] +inherits = *common* +bottom_solid_layers = 4 +bridge_flow_ratio = 25% +external_perimeter_speed = 42 +infill_speed = 60 +layer_height = 0.2 +perimeter_speed = 42 +solid_infill_speed = 55 +top_infill_extrusion_width = 0.8 +top_solid_layers = 5 + +[print:*0.4mm Nozzle*] +extrusion_width = 0 +first_layer_extrusion_width = 120% +perimeter_extrusion_width = 115% +external_perimeter_extrusion_width = 105% +infill_extrusion_width = 115% +solid_infill_extrusion_width = 115% +top_infill_extrusion_width = 105% +support_material_extrusion_width = 100% +first_layer_height = 0.3 +infill_overlap = 20% +compatible_printers_condition = nozzle_diameter[0]==0.4 + +[print:*0.6mm Nozzle*] +extrusion_width = 0 +first_layer_extrusion_width = 120% +perimeter_extrusion_width = 120% +external_perimeter_extrusion_width = 110% +infill_extrusion_width = 120% +solid_infill_extrusion_width = 120% +top_infill_extrusion_width = 105% +support_material_extrusion_width = 100% +first_layer_height = 0.4 +infill_overlap = 20% +compatible_printers_condition = nozzle_diameter[0]==0.6 + +[print:*1.2mm Nozzle*] +extrusion_width = 0 +first_layer_extrusion_width = 120% +perimeter_extrusion_width = 120% +external_perimeter_extrusion_width = 110% +infill_extrusion_width = 120% +solid_infill_extrusion_width = 120% +top_infill_extrusion_width = 105% +support_material_extrusion_width = 100% +first_layer_height = 0.3 +infill_overlap = 15% +compatible_printers_condition = nozzle_diameter[0]==1.2 + +# MBL 1.2mm Nozzle# +[print:0.20mm QUALITY @MBL 1.2mm Nozzle] +inherits = *0.20mm*; *MBL*; *1.2mm Nozzle* +# alias = 0.20mm QUALITY +bridge_speed = 50 +compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_MELTINGPLOT.*/ and printer_notes=~/.*PRINTER_MODEL_MBL.*/ and nozzle_diameter[0]==1.2 +external_perimeter_speed = 42 +infill_speed = 60 +max_print_speed = 120 +perimeter_speed = 45 +solid_infill_speed = 60 +top_solid_infill_speed = 42 +fill_pattern = cubic +fill_density = 15% + +# MBL 1.2mm Nozzle# +[print:0.20mm SPEED @MBL 1.2mm Nozzle] +inherits = *0.20mm*; *MBL*; *1.2mm Nozzle* +# alias = 0.20mm SPEED +bridge_speed = 60 +compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_MELTINGPLOT.*/ and printer_notes=~/.*PRINTER_MODEL_MBL.*/ and nozzle_diameter[0]==1.2 +external_perimeter_speed = 42 +infill_speed = 80 +max_print_speed = 120 +perimeter_speed = 80 +solid_infill_speed = 80 +support_material_speed = 80 +top_solid_infill_speed = 42 +fill_pattern = cubic +fill_density = 15% + +# MBL 0.4mm Nozzle# +[print:0.20mm QUALITY @MBL 0.4mm Nozzle] +inherits = *0.20mm*; *MBL*; *0.4mm Nozzle* +# alias = 0.20mm QUALITY +bridge_speed = 50 +compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_MELTINGPLOT.*/ and printer_notes=~/.*PRINTER_MODEL_MBL.*/ and nozzle_diameter[0]==0.4 +external_perimeter_speed = 42 +infill_speed = 80 +max_print_speed = 200 +perimeter_speed = 45 +solid_infill_speed = 80 +top_solid_infill_speed = 42 +fill_pattern = cubic +fill_density = 15% + +# MBL 0.4mm Nozzle# +[print:0.20mm SPEED @MBL 0.4mm Nozzle] +inherits = *0.20mm*; *MBL*; *0.4mm Nozzle* +# alias = 0.20mm SPEED +bridge_speed = 60 +compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_MELTINGPLOT.*/ and printer_notes=~/.*PRINTER_MODEL_MBL.*/ and nozzle_diameter[0]==0.4 +external_perimeter_speed = 42 +infill_speed = 120 +max_print_speed = 200 +perimeter_speed = 120 +solid_infill_speed = 80 +support_material_speed = 80 +top_solid_infill_speed = 42 +fill_pattern = cubic +fill_density = 15% + +# MBL 0.6mm Nozzle# +[print:0.20mm QUALITY @MBL 0.6mm Nozzle] +inherits = *0.20mm*; *MBL*; *0.6mm Nozzle* +# alias = 0.20mm QUALITY +bridge_speed = 50 +compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_MELTINGPLOT.*/ and printer_notes=~/.*PRINTER_MODEL_MBL.*/ and nozzle_diameter[0]==0.6 +external_perimeter_speed = 42 +infill_speed = 80 +max_print_speed = 200 +perimeter_speed = 45 +solid_infill_speed = 80 +top_solid_infill_speed = 42 +fill_pattern = cubic +fill_density = 15% + +# MBL 0.6mm Nozzle# +[print:0.20mm SPEED @MBL 0.6mm Nozzle] +inherits = *0.20mm*; *MBL*; *0.6mm Nozzle* +# alias = 0.20mm SPEED +bridge_speed = 60 +compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_MELTINGPLOT.*/ and printer_notes=~/.*PRINTER_MODEL_MBL.*/ and nozzle_diameter[0]==0.6 +external_perimeter_speed = 42 +infill_speed = 120 +max_print_speed = 200 +perimeter_speed = 120 +solid_infill_speed = 80 +support_material_speed = 80 +top_solid_infill_speed = 42 +fill_pattern = cubic +fill_density = 15% + +# MBL 0.8mm Nozzle# +[print:0.20mm QUALITY @MBL] +inherits = *0.20mm*; *MBL* +# alias = 0.20mm QUALITY +bridge_speed = 50 +compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_MELTINGPLOT.*/ and printer_notes=~/.*PRINTER_MODEL_MBL.*/ and nozzle_diameter[0]==0.8 +external_perimeter_speed = 42 +infill_speed = 80 +max_print_speed = 200 +perimeter_speed = 45 +solid_infill_speed = 80 +top_solid_infill_speed = 42 +fill_pattern = cubic +fill_density = 15% + +# MBL 0.8mm Nozzle# +[print:0.20mm SPEED @MBL] +inherits = *0.20mm*; *MBL* +# alias = 0.20mm SPEED +bridge_speed = 60 +compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_MELTINGPLOT.*/ and printer_notes=~/.*PRINTER_MODEL_MBL.*/ and nozzle_diameter[0]==0.8 +external_perimeter_speed = 42 +infill_speed = 120 +max_print_speed = 200 +perimeter_speed = 120 +solid_infill_speed = 80 +support_material_speed = 80 +top_solid_infill_speed = 42 +fill_pattern = cubic +fill_density = 15% + +# Common filament preset +[filament:*common*] +cooling = 0 +compatible_printers = +extrusion_multiplier = 1 +filament_cost = 0 +filament_density = 0 +filament_diameter = 2.85 +filament_notes = "" +filament_settings_id = "" +filament_soluble = 0 +min_print_speed = 15 +slowdown_below_layer_time = 20 +compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_MELTINGPLOT.*/ + +[filament:*PLA*] +inherits = *common* +bed_temperature = 60 +fan_below_layer_time = 100 +filament_colour = #FF3232 +filament_max_volumetric_speed = 20 +filament_type = PLA +filament_density = 1.24 +filament_cost = 20 +first_layer_bed_temperature = 60 +first_layer_temperature = 215 +fan_always_on = 1 +cooling = 1 +max_fan_speed = 100 +min_fan_speed = 100 +bridge_fan_speed = 100 +disable_fan_first_layers = 1 +temperature = 210 + +[filament:*ABS*] +inherits = *common* +bed_temperature = 100 +fan_below_layer_time = 30 +filament_colour = #FF3232 +filament_max_volumetric_speed = 15 +filament_type = ABS +filament_density = 1.1 +filament_cost = 20 +first_layer_bed_temperature = 105 +first_layer_temperature = 255 +fan_always_on = 0 +cooling = 1 +max_fan_speed = 50 +min_fan_speed = 15 +bridge_fan_speed = 25 +disable_fan_first_layers = 2 +temperature = 250 + +[filament:*PETG*] +inherits = *common* +bed_temperature = 85 +fan_below_layer_time = 30 +filament_colour = #FF3232 +filament_max_volumetric_speed = 20 +filament_type = PETG +filament_density = 1.27 +filament_cost = 35 +first_layer_bed_temperature = 85 +first_layer_temperature = 240 +fan_always_on = 1 +cooling = 1 +max_fan_speed = 100 +min_fan_speed = 45 +bridge_fan_speed = 100 +disable_fan_first_layers = 2 +temperature = 240 +slowdown_below_layer_time = 10 + +[filament:*ASA*] +inherits = *common* +bed_temperature = 90 +fan_below_layer_time = 30 +filament_colour = #FF3232 +filament_max_volumetric_speed = 28 +filament_type = ASA +filament_density = 1.11 +filament_cost = 46.65 +first_layer_bed_temperature = 90 +first_layer_temperature = 255 +fan_always_on = 0 +cooling = 1 +max_fan_speed = 50 +min_fan_speed = 10 +bridge_fan_speed = 100 +disable_fan_first_layers = 2 +temperature = 255 +slowdown_below_layer_time = 10 + +[filament:Meltingplot PLA] +inherits = *PLA* +filament_vendor = Meltingplot +first_layer_bed_temperature = 65 +temperature = 210 +filament_cost = 34.9 +filament_colour = #F8F8F8 + +[filament:Meltingplot StoneFil] +inherits = *PLA* +filament_vendor = Meltingplot +first_layer_bed_temperature = 65 +temperature = 225 +filament_cost = 68.82 +extrusion_multiplier = 1.05 +filament_colour = #F8F8F8 +max_fan_speed = 60 +min_fan_speed = 30 +filament_max_volumetric_speed=8 + +[filament:Meltingplot ABS] +inherits = *ABS* +filament_vendor = Meltingplot +first_layer_bed_temperature = 105 +temperature = 250 +filament_cost = 30 +filament_colour = #F8F8F8 + +[filament:Meltingplot ASA] +inherits = *ASA* +filament_vendor = Meltingplot +filament_cost = 46.65 +filament_colour = #123123 + +[filament:Meltingplot PETG] +inherits = *PETG* +filament_vendor = Meltingplot +filament_cost = 35 +filament_colour = #123123 +bed_temperature = 100 +first_layer_bed_temperature = 100 +compatible_printers_condition = nozzle_diameter[0]>0.6 + +[filament:Meltingplot PETG @0.4mm] +inherits = *PETG* +filament_vendor = Meltingplot +filament_cost = 35 +filament_colour = #123123 +bed_temperature = 100 +first_layer_bed_temperature = 100 +temperature = 235 +first_layer_temperature = 235 +filament_max_volumetric_speed = 15 +compatible_printers_condition = nozzle_diameter[0]==0.4 + +[filament:Meltingplot PETG @0.6mm] +inherits = *PETG* +filament_vendor = Meltingplot +filament_cost = 35 +filament_colour = #123123 +bed_temperature = 100 +first_layer_bed_temperature = 100 +temperature = 240 +first_layer_temperature = 240 +filament_max_volumetric_speed = 16 +compatible_printers_condition = nozzle_diameter[0]==0.6 + +[printer:*common*] +printer_technology = FFF +bed_shape = 0x0,835x0,835x405,0x405 +before_layer_gcode = ;BEFORE_LAYER_CHANGE\nG92 E0.0\n;[layer_z]\n\n +between_objects_gcode = +deretract_speed = 0 +end_gcode = M98 P"0:/sys/meltingplot/print_end" +extruder_offset = 0x0 +gcode_flavor = reprapfirmware +host_type = duet +silent_mode = 0 +remaining_times = 0 +machine_max_acceleration_e = 10000 +machine_max_acceleration_extruding = 2000 +machine_max_acceleration_retracting = 1500 +machine_max_acceleration_x = 9000 +machine_max_acceleration_y = 9000 +machine_max_acceleration_z = 500 +machine_max_feedrate_e = 120 +machine_max_feedrate_x = 500 +machine_max_feedrate_y = 500 +machine_max_feedrate_z = 12 +machine_max_jerk_e = 2.5 +machine_max_jerk_x = 10 +machine_max_jerk_y = 10 +machine_max_jerk_z = 0.2 +machine_min_extruding_rate = 0 +machine_min_travel_rate = 0 +layer_gcode = ;AFTER_LAYER_CHANGE\n;[layer_z] +max_layer_height = 0.8 +min_layer_height = 0.1 +max_print_height = 394 +nozzle_diameter = 0.8 +octoprint_apikey = +octoprint_host = +printer_notes = Dont remove the following keywords! These keywords are used in the "compatible printer" condition of the print and filament profiles to link the particular print and filament profiles to this printer profile.\nPRINTER_VENDOR_MELTINGPLOT\n +printer_settings_id = +retract_before_travel = 4 +retract_before_wipe = 0% +retract_layer_change = 1 +retract_length = 0.8 +retract_length_toolchange = 4 +retract_lift = 0.6 +retract_lift_above = 0 +retract_lift_below = 199 +retract_restart_extra = 0 +retract_restart_extra_toolchange = 0 +retract_speed = 35 +serial_port = +serial_speed = 250000 +single_extruder_multi_material = 0 +start_gcode = M140 P0 S{first_layer_bed_temperature[0]} ; set bed temp\nG10 P0 R{first_layer_temperature[0] + standby_temperature_delta} S{first_layer_temperature[0]}\n\nM83 ; use relative distances for extrusion\nG90 ; use absolute coordinates\n\nM98 P"0:/sys/meltingplot/print_start" +toolchange_gcode = +use_firmware_retraction = 1 +use_relative_e_distances = 1 +use_volumetric_e = 0 +variable_layer_height = 1 +wipe = 0 +z_offset = 0 +printer_model = MBL133 +default_print_profile = 0.20mm QUALITY @MBL +default_filament_profile = Meltingplot PLA + +[printer:Meltingplot MBL 133 0.8mm nozzle] +inherits = *common* +printer_variant = 0.8 +retract_lift = 0.0 +before_layer_gcode = ;BEFORE_LAYER_CHANGE\n;[layer_z]\n\n +printer_notes = Dont remove the following keywords! These keywords are used in the "compatible printer" condition of the print and filament profiles to link the particular print and filament profiles to this printer profile.\nPRINTER_VENDOR_MELTINGPLOT\nPRINTER_MODEL_MBL\n + +[printer:Meltingplot MBL 133 0.4mm nozzle] +inherits = Meltingplot MBL 133 0.8mm nozzle +nozzle_diameter = 0.4 +max_layer_height = 0.4 +min_layer_height = 0.05 +printer_variant = 0.4 +default_print_profile = 0.20mm QUALITY @MBL 0.4mm Nozzle +default_filament_profile = Meltingplot PLA + +[printer:Meltingplot MBL 133 0.6mm nozzle] +inherits = Meltingplot MBL 133 0.8mm nozzle +nozzle_diameter = 0.6 +max_layer_height = 0.6 +min_layer_height = 0.05 +printer_variant = 0.6 +default_print_profile = 0.20mm QUALITY @MBL 0.6mm Nozzle +default_filament_profile = Meltingplot PLA + +[printer:Meltingplot MBL 133 1.2mm nozzle] +inherits = Meltingplot MBL 133 0.8mm nozzle +nozzle_diameter = 1.2 +max_layer_height = 1.2 +min_layer_height = 0.1 +printer_variant = 1.2 +default_print_profile = 0.20mm QUALITY @MBL 1.2mm Nozzle +default_filament_profile = Meltingplot PLA + +[printer:Meltingplot MBL 136] +bed_shape = 0x0,850x0,850x405,0x405 +max_print_height = 396 +printer_model = MBL136 + +[printer:Meltingplot MBL 136 0.8mm nozzle] +inherits = Meltingplot MBL 133 0.8mm nozzle; Meltingplot MBL 136 + +[printer:Meltingplot MBL 136 0.4mm nozzle] +inherits = Meltingplot MBL 133 0.4mm nozzle; Meltingplot MBL 136 + +[printer:Meltingplot MBL 136 0.6mm nozzle] +inherits = Meltingplot MBL 133 0.6mm nozzle; Meltingplot MBL 136 + +[printer:Meltingplot MBL 136 1.2mm nozzle] +inherits = Meltingplot MBL 133 1.2mm nozzle; Meltingplot MBL 136 + +[printer:Meltingplot MBL 480] +bed_shape = 0x0,850x0,850x405,0x405 +max_print_height = 1396 +printer_model = MBL480 + +[printer:Meltingplot MBL 480 0.8mm nozzle] +inherits = Meltingplot MBL 133 0.8mm nozzle; Meltingplot MBL 480 + +[printer:Meltingplot MBL 480 0.4mm nozzle] +inherits = Meltingplot MBL 133 0.4mm nozzle; Meltingplot MBL 480 + +[printer:Meltingplot MBL 480 0.6mm nozzle] +inherits = Meltingplot MBL 133 0.6mm nozzle; Meltingplot MBL 480 + +[printer:Meltingplot MBL 480 1.2mm nozzle] +inherits = Meltingplot MBL 133 1.2mm nozzle; Meltingplot MBL 480 + +[printer_model:MBL133] +name = Meltingplot MBL 133 +variants = 0.8; 0.4; 1.2; 0.6 +technology = FFF +family = MBL +bed_model = A007_Printbed_mbl133.stl +bed_texture = printbed_outline_133.svg +default_materials = Meltingplot PETG; Meltingplot PLA; Generic PLA; Generic ABS; Generic PETG + +[printer_model:MBL136] +name = Meltingplot MBL 136 +variants = 0.8; 0.4; 1.2; 0.6 +technology = FFF +family = MBL +bed_model = A007_Printbed_mbl136.stl +bed_texture = printbed_outline_136.svg +default_materials = Meltingplot PETG; Meltingplot PLA; Generic PLA; Generic ABS; Generic PETG + +[printer_model:MBL480] +name = Meltingplot MBL 480 +variants = 0.8; 0.4; 1.2; 0.6 +technology = FFF +family = MBL +bed_model = A007_Printbed_mbl136.stl +bed_texture = printbed_outline_480.svg +default_materials = Meltingplot PETG; Meltingplot PLA; Generic PLA; Generic ABS; Generic PETG
\ No newline at end of file |