Updated the bundled config profile with the new compatible_printers_condition.

1 files changed, 131 insertions, 79 deletions

diff --git a/resources/profiles/Original Prusa i3 MK3, MK2S, MK2 and MK2S-MMU.ini b/resources/profiles/Original Prusa i3 MK3, MK2S, MK2 and MK2S-MMU.ini
index ae21f862d..cb076ac35 100644
--- a/resources/profiles/Original Prusa i3 MK3, MK2S, MK2 and MK2S-MMU.ini
+++ b/resources/profiles/Original Prusa i3 MK3, MK2S, MK2 and MK2S-MMU.ini
@@ -1,4 +1,4 @@
-# generated by Slic3r Prusa Edition 1.38.4 on 2017-12-10 at 09:05:01
+# generated by Slic3r Prusa Edition 1.38.4 on 2017-12-19 at 17:08:04
 
 [print:0.05mm DETAIL]
 avoid_crossing_perimeters = 0
@@ -9,7 +9,8 @@ bridge_flow_ratio = 0.7
 bridge_speed = 20
 brim_width = 0
 clip_multipart_objects = 1
-compatible_printers = "Original Prusa i3 MK2";"Original Prusa i3 MK2 MM Single Mode"
+compatible_printers = 
+compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK2.*/ and nozzle_diameter[0]==0.4 and num_extruders==1
 complete_objects = 0
 default_acceleration = 500
 dont_support_bridges = 1
@@ -114,7 +115,8 @@ bridge_flow_ratio = 0.7
 bridge_speed = 20
 brim_width = 0
 clip_multipart_objects = 1
-compatible_printers = "Original Prusa i3 MK2 0.25 nozzle";"Original Prusa i3 MK2 MM Single Mode 0.25 nozzle"
+compatible_printers = 
+compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK2.*/ and nozzle_diameter[0]==0.25 and num_extruders==1
 complete_objects = 0
 default_acceleration = 500
 dont_support_bridges = 1
@@ -219,7 +221,8 @@ bridge_flow_ratio = 0.7
 bridge_speed = 20
 brim_width = 0
 clip_multipart_objects = 1
-compatible_printers = "Original Prusa i3 MK3"
+compatible_printers = 
+compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK3.*/
 complete_objects = 0
 default_acceleration = 500
 dont_support_bridges = 1
@@ -324,7 +327,8 @@ bridge_flow_ratio = 0.7
 bridge_speed = 20
 brim_width = 0
 clip_multipart_objects = 1
-compatible_printers = "Original Prusa i3 MK2";"Original Prusa i3 MK2 MM Single Mode"
+compatible_printers = 
+compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK2.*/ and nozzle_diameter[0]==0.4 and num_extruders==1
 complete_objects = 0
 default_acceleration = 1000
 dont_support_bridges = 1
@@ -429,7 +433,8 @@ bridge_flow_ratio = 0.7
 bridge_speed = 20
 brim_width = 0
 clip_multipart_objects = 1
-compatible_printers = "Original Prusa i3 MK2 0.25 nozzle";"Original Prusa i3 MK2 MM Single Mode 0.25 nozzle"
+compatible_printers = 
+compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK2.*/ and nozzle_diameter[0]==0.25
 complete_objects = 0
 default_acceleration = 1000
 dont_support_bridges = 1
@@ -534,7 +539,8 @@ bridge_flow_ratio = 0.8
 bridge_speed = 30
 brim_width = 0
 clip_multipart_objects = 1
-compatible_printers = "Original Prusa i3 MK3"
+compatible_printers = 
+compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK3.*/
 complete_objects = 0
 default_acceleration = 1000
 dont_support_bridges = 1
@@ -639,7 +645,8 @@ bridge_flow_ratio = 0.95
 bridge_speed = 20
 brim_width = 0
 clip_multipart_objects = 1
-compatible_printers = "Original Prusa i3 MK2";"Original Prusa i3 MK2 MM Single Mode";"Original Prusa i3 MK2 MultiMaterial"
+compatible_printers = 
+compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK2.*/ and nozzle_diameter[0]==0.4
 complete_objects = 0
 default_acceleration = 1000
 dont_support_bridges = 1
@@ -744,7 +751,8 @@ bridge_flow_ratio = 0.8
 bridge_speed = 20
 brim_width = 0
 clip_multipart_objects = 1
-compatible_printers = "Original Prusa i3 MK2";"Original Prusa i3 MK2 MM Single Mode";"Original Prusa i3 MK2 MultiMaterial"
+compatible_printers = 
+compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK2.*/ and nozzle_diameter[0]==0.4
 complete_objects = 0
 default_acceleration = 1000
 dont_support_bridges = 1
@@ -849,7 +857,8 @@ bridge_flow_ratio = 0.7
 bridge_speed = 20
 brim_width = 0
 clip_multipart_objects = 1
-compatible_printers = "Original Prusa i3 MK2 0.25 nozzle";"Original Prusa i3 MK2 MM Single Mode 0.25 nozzle";"Original Prusa i3 MK2 MultiMaterial 0.25 nozzle"
+compatible_printers = 
+compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK2.*/ and nozzle_diameter[0]==0.25
 complete_objects = 0
 default_acceleration = 1000
 dont_support_bridges = 1
@@ -954,7 +963,8 @@ bridge_flow_ratio = 0.8
 bridge_speed = 20
 brim_width = 0
 clip_multipart_objects = 1
-compatible_printers = "Original Prusa i3 MK2 0.6 nozzle";"Original Prusa i3 MK2 MM Single Mode 0.6 nozzle";"Original Prusa i3 MK2 MultiMaterial 0.6 nozzle"
+compatible_printers = 
+compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK2.*/ and nozzle_diameter[0]==0.6
 complete_objects = 0
 default_acceleration = 1000
 dont_support_bridges = 1
@@ -1059,7 +1069,8 @@ bridge_flow_ratio = 0.8
 bridge_speed = 30
 brim_width = 0
 clip_multipart_objects = 1
-compatible_printers = "Original Prusa i3 MK3"
+compatible_printers = 
+compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK3.*/
 complete_objects = 0
 default_acceleration = 1000
 dont_support_bridges = 1
@@ -1164,7 +1175,8 @@ bridge_flow_ratio = 0.8
 bridge_speed = 20
 brim_width = 0
 clip_multipart_objects = 1
-compatible_printers = "Original Prusa i3 MK2 MultiMaterial"
+compatible_printers = 
+compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK2.*/ and nozzle_diameter[0]==0.4 and num_extruders>1
 complete_objects = 0
 default_acceleration = 1000
 dont_support_bridges = 1
@@ -1269,7 +1281,8 @@ bridge_flow_ratio = 0.8
 bridge_speed = 20
 brim_width = 0
 clip_multipart_objects = 1
-compatible_printers = "Original Prusa i3 MK2 MultiMaterial"
+compatible_printers = 
+compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK2.*/ and nozzle_diameter[0]==0.4 and num_extruders>1
 complete_objects = 0
 default_acceleration = 1000
 dont_support_bridges = 1
@@ -1374,7 +1387,8 @@ bridge_flow_ratio = 0.95
 bridge_speed = 20
 brim_width = 0
 clip_multipart_objects = 1
-compatible_printers = "Original Prusa i3 MK2";"Original Prusa i3 MK2 MM Single Mode";"Original Prusa i3 MK2 MultiMaterial"
+compatible_printers = 
+compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK2.*/ and nozzle_diameter[0]==0.4
 complete_objects = 0
 default_acceleration = 1000
 dont_support_bridges = 1
@@ -1479,7 +1493,8 @@ bridge_flow_ratio = 0.95
 bridge_speed = 20
 brim_width = 0
 clip_multipart_objects = 1
-compatible_printers = "Original Prusa i3 MK2";"Original Prusa i3 MK2 MM Single Mode";"Original Prusa i3 MK2 MultiMaterial"
+compatible_printers = 
+compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK2.*/ and nozzle_diameter[0]==0.4
 complete_objects = 0
 default_acceleration = 1000
 dont_support_bridges = 1
@@ -1584,7 +1599,8 @@ bridge_flow_ratio = 0.8
 bridge_speed = 20
 brim_width = 0
 clip_multipart_objects = 1
-compatible_printers = "Original Prusa i3 MK2 0.6 nozzle";"Original Prusa i3 MK2 MM Single Mode 0.6 nozzle";"Original Prusa i3 MK2 MultiMaterial 0.6 nozzle"
+compatible_printers = 
+compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK2.*/ and nozzle_diameter[0]==0.6
 complete_objects = 0
 default_acceleration = 1000
 dont_support_bridges = 1
@@ -1689,7 +1705,8 @@ bridge_flow_ratio = 0.8
 bridge_speed = 30
 brim_width = 0
 clip_multipart_objects = 1
-compatible_printers = "Original Prusa i3 MK3"
+compatible_printers = 
+compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK3.*/
 complete_objects = 0
 default_acceleration = 1000
 dont_support_bridges = 1
@@ -1794,7 +1811,8 @@ bridge_flow_ratio = 0.95
 bridge_speed = 20
 brim_width = 0
 clip_multipart_objects = 1
-compatible_printers = "Original Prusa i3 MK2 MultiMaterial"
+compatible_printers = 
+compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK2.*/ and nozzle_diameter[0]==0.4 and num_extruders>1
 complete_objects = 0
 default_acceleration = 1000
 dont_support_bridges = 1
@@ -1899,7 +1917,8 @@ bridge_flow_ratio = 0.95
 bridge_speed = 20
 brim_width = 0
 clip_multipart_objects = 1
-compatible_printers = "Original Prusa i3 MK2 MultiMaterial"
+compatible_printers = 
+compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK2.*/ and nozzle_diameter[0]==0.4 and num_extruders>1
 complete_objects = 0
 default_acceleration = 1000
 dont_support_bridges = 1
@@ -2004,7 +2023,8 @@ bridge_flow_ratio = 0.95
 bridge_speed = 20
 brim_width = 0
 clip_multipart_objects = 1
-compatible_printers = "Original Prusa i3 MK2";"Original Prusa i3 MK2 MM Single Mode";"Original Prusa i3 MK2 MultiMaterial"
+compatible_printers = 
+compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK2.*/ and nozzle_diameter[0]==0.4
 complete_objects = 0
 default_acceleration = 1000
 dont_support_bridges = 1
@@ -2109,7 +2129,8 @@ bridge_flow_ratio = 0.8
 bridge_speed = 20
 brim_width = 0
 clip_multipart_objects = 1
-compatible_printers = "Original Prusa i3 MK2 0.6 nozzle";"Original Prusa i3 MK2 MM Single Mode 0.6 nozzle";"Original Prusa i3 MK2 MultiMaterial 0.6 nozzle"
+compatible_printers = 
+compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK2.*/ and nozzle_diameter[0]==0.6
 complete_objects = 0
 default_acceleration = 1000
 dont_support_bridges = 1
@@ -2214,7 +2235,8 @@ bridge_flow_ratio = 0.8
 bridge_speed = 30
 brim_width = 0
 clip_multipart_objects = 1
-compatible_printers = "Original Prusa i3 MK3"
+compatible_printers = 
+compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK3.*/
 complete_objects = 0
 default_acceleration = 1000
 dont_support_bridges = 1
@@ -2319,7 +2341,8 @@ bridge_flow_ratio = 0.8
 bridge_speed = 20
 brim_width = 0
 clip_multipart_objects = 1
-compatible_printers = "Original Prusa i3 MK2 MultiMaterial 0.6 nozzle"
+compatible_printers = 
+compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK2.*/ and nozzle_diameter[0]==0.6 and num_extruders>1
 complete_objects = 0
 default_acceleration = 1000
 dont_support_bridges = 1
@@ -2424,7 +2447,8 @@ bridge_flow_ratio = 0.8
 bridge_speed = 20
 brim_width = 0
 clip_multipart_objects = 1
-compatible_printers = "Original Prusa i3 MK2 MultiMaterial 0.6 nozzle"
+compatible_printers = 
+compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK2.*/ and nozzle_diameter[0]==0.6 and num_extruders>1
 complete_objects = 0
 default_acceleration = 1000
 dont_support_bridges = 1
@@ -2523,7 +2547,8 @@ xy_size_compensation = 0
 [filament:ColorFabb Brass Bronze  1.75mm]
 bed_temperature = 60
 bridge_fan_speed = 100
-compatible_printers = "Original Prusa i3 MK2";"Original Prusa i3 MK2 0.6 nozzle";"Original Prusa i3 MK2 MM Single Mode";"Original Prusa i3 MK2 MM Single Mode 0.6 nozzle";"Original Prusa i3 MK2 MultiMaterial";"Original Prusa i3 MK2 MultiMaterial 0.6 nozzle";"Original Prusa i3 MK3"
+compatible_printers = 
+compatible_printers_condition = nozzle_diameter[0]>0.35
 cooling = 1
 disable_fan_first_layers = 1
 end_filament_gcode = "; Filament-specific end gcode"
@@ -2545,13 +2570,14 @@ max_fan_speed = 100
 min_fan_speed = 85
 min_print_speed = 5
 slowdown_below_layer_time = 10
-start_filament_gcode = "M900 K{if printer_preset==\"Original Prusa i3 MK2 MultiMaterial\"}200{elsif printer_preset==\"Original Prusa i3 MK2 MM Single Mode\"}200{else}10{endif}; Filament gcode"
+start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}200{else}10{endif}; Filament gcode"
 temperature = 210
 
 [filament:ColorFabb HT 1.75mm]
 bed_temperature = 105
 bridge_fan_speed = 30
 compatible_printers = 
+compatible_printers_condition = 
 cooling = 1
 disable_fan_first_layers = 3
 end_filament_gcode = "; Filament-specific end gcode"
@@ -2573,13 +2599,14 @@ max_fan_speed = 20
 min_fan_speed = 10
 min_print_speed = 5
 slowdown_below_layer_time = 10
-start_filament_gcode = "M900 K{if printer_preset==\"Original Prusa i3 MK2 MultiMaterial\"}200{elsif printer_preset==\"Original Prusa i3 MK2 MM Single Mode\"}200{else}45{endif}; Filament gcode"
+start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}200{else}45{endif}; Filament gcode"
 temperature = 270
 
 [filament:ColorFabb PLA-PHA]
 bed_temperature = 60
 bridge_fan_speed = 100
 compatible_printers = 
+compatible_printers_condition = 
 cooling = 1
 disable_fan_first_layers = 1
 end_filament_gcode = "; Filament-specific end gcode"
@@ -2601,13 +2628,14 @@ max_fan_speed = 100
 min_fan_speed = 85
 min_print_speed = 15
 slowdown_below_layer_time = 10
-start_filament_gcode = "M900 K{if printer_preset==\"Original Prusa i3 MK2 MultiMaterial\"}200{elsif printer_preset==\"Original Prusa i3 MK2 MM Single Mode\"}200{else}30{endif}; Filament gcode"
+start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}200{else}30{endif}; Filament gcode"
 temperature = 210
 
 [filament:ColorFabb Woodfil 1.75mm]
 bed_temperature = 60
 bridge_fan_speed = 100
-compatible_printers = "Original Prusa i3 MK2";"Original Prusa i3 MK2 0.6 nozzle";"Original Prusa i3 MK2 MM Single Mode";"Original Prusa i3 MK2 MM Single Mode 0.6 nozzle";"Original Prusa i3 MK2 MultiMaterial";"Original Prusa i3 MK2 MultiMaterial 0.6 nozzle";"Original Prusa i3 MK3"
+compatible_printers = 
+compatible_printers_condition = nozzle_diameter[0]>0.35
 cooling = 1
 disable_fan_first_layers = 1
 end_filament_gcode = "; Filament-specific end gcode"
@@ -2629,13 +2657,14 @@ max_fan_speed = 100
 min_fan_speed = 85
 min_print_speed = 5
 slowdown_below_layer_time = 10
-start_filament_gcode = "M900 K{if printer_preset==\"Original Prusa i3 MK2 MultiMaterial\"}200{elsif printer_preset==\"Original Prusa i3 MK2 MM Single Mode\"}200{else}10{endif}; Filament gcode"
+start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}200{else}10{endif}; Filament gcode"
 temperature = 200
 
 [filament:ColorFabb XT 1.75mm]
 bed_temperature = 65
 bridge_fan_speed = 50
 compatible_printers = 
+compatible_printers_condition = 
 cooling = 1
 disable_fan_first_layers = 3
 end_filament_gcode = "; Filament-specific end gcode"
@@ -2657,13 +2686,14 @@ max_fan_speed = 50
 min_fan_speed = 30
 min_print_speed = 5
 slowdown_below_layer_time = 10
-start_filament_gcode = "M900 K{if printer_preset==\"Original Prusa i3 MK2 MultiMaterial\"}200{elsif printer_preset==\"Original Prusa i3 MK2 MM Single Mode\"}200{else}45{endif}; Filament gcode"
+start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}200{else}45{endif}; Filament gcode"
 temperature = 240
 
 [filament:ColorFabb XT-CF20 1.75mm]
 bed_temperature = 90
 bridge_fan_speed = 50
 compatible_printers = 
+compatible_printers_condition = 
 cooling = 1
 disable_fan_first_layers = 3
 end_filament_gcode = "; Filament-specific end gcode"
@@ -2685,13 +2715,14 @@ max_fan_speed = 50
 min_fan_speed = 30
 min_print_speed = 5
 slowdown_below_layer_time = 10
-start_filament_gcode = "M900 K{if printer_preset==\"Original Prusa i3 MK2 MultiMaterial\"}200{elsif printer_preset==\"Original Prusa i3 MK2 MM Single Mode\"}200{else}30{endif}; Filament gcode"
+start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}200{else}30{endif}; Filament gcode"
 temperature = 260
 
 [filament:ColorFabb nGen 1.75mm]
 bed_temperature = 85
 bridge_fan_speed = 40
 compatible_printers = 
+compatible_printers_condition = 
 cooling = 1
 disable_fan_first_layers = 3
 end_filament_gcode = "; Filament-specific end gcode"
@@ -2713,13 +2744,14 @@ max_fan_speed = 35
 min_fan_speed = 20
 min_print_speed = 5
 slowdown_below_layer_time = 10
-start_filament_gcode = "M900 K{if printer_preset==\"Original Prusa i3 MK2 MultiMaterial\"}200{elsif printer_preset==\"Original Prusa i3 MK2 MM Single Mode\"}200{else}45{endif}; Filament gcode"
+start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}200{else}45{endif}; Filament gcode"
 temperature = 240
 
 [filament:ColorFabb nGen flex]
 bed_temperature = 85
 bridge_fan_speed = 40
 compatible_printers = 
+compatible_printers_condition = 
 cooling = 1
 disable_fan_first_layers = 3
 end_filament_gcode = "; Filament-specific end gcode"
@@ -2741,13 +2773,14 @@ max_fan_speed = 35
 min_fan_speed = 20
 min_print_speed = 5
 slowdown_below_layer_time = 10
-start_filament_gcode = "M900 K{if printer_preset==\"Original Prusa i3 MK2 MultiMaterial\"}200{elsif printer_preset==\"Original Prusa i3 MK2 MM Single Mode\"}200{else}10{endif}; Filament gcode"
+start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}200{else}10{endif}; Filament gcode"
 temperature = 260
 
 [filament:E3D Edge]
 bed_temperature = 90
 bridge_fan_speed = 50
 compatible_printers = 
+compatible_printers_condition = 
 cooling = 1
 disable_fan_first_layers = 3
 end_filament_gcode = "; Filament-specific end gcode"
@@ -2769,13 +2802,14 @@ max_fan_speed = 50
 min_fan_speed = 30
 min_print_speed = 5
 slowdown_below_layer_time = 10
-start_filament_gcode = "M900 K{if printer_preset==\"Original Prusa i3 MK2 MultiMaterial\"}200{elsif printer_preset==\"Original Prusa i3 MK2 MM Single Mode\"}200{else}45{endif}; Filament gcode"
+start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}200{else}45{endif}; Filament gcode"
 temperature = 240
 
 [filament:E3D PC-ABS 1.75mm]
 bed_temperature = 100
 bridge_fan_speed = 30
 compatible_printers = 
+compatible_printers_condition = 
 cooling = 0
 disable_fan_first_layers = 3
 end_filament_gcode = "; Filament-specific end gcode"
@@ -2797,13 +2831,14 @@ max_fan_speed = 30
 min_fan_speed = 10
 min_print_speed = 5
 slowdown_below_layer_time = 10
-start_filament_gcode = "M900 K{if printer_preset==\"Original Prusa i3 MK2 MultiMaterial\"}200{elsif printer_preset==\"Original Prusa i3 MK2 MM Single Mode\"}200{else}30{endif}; Filament gcode"
+start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}200{else}30{endif}; Filament gcode"
 temperature = 270
 
 [filament:Fillamentum ABS 1.75mm]
 bed_temperature = 100
 bridge_fan_speed = 30
 compatible_printers = 
+compatible_printers_condition = 
 cooling = 0
 disable_fan_first_layers = 3
 end_filament_gcode = "; Filament-specific end gcode"
@@ -2825,13 +2860,14 @@ max_fan_speed = 30
 min_fan_speed = 10
 min_print_speed = 5
 slowdown_below_layer_time = 10
-start_filament_gcode = "M900 K{if printer_preset==\"Original Prusa i3 MK2 MultiMaterial\"}200{elsif printer_preset==\"Original Prusa i3 MK2 MM Single Mode\"}200{else}30{endif}; Filament gcode"
+start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}200{else}30{endif}; Filament gcode"
 temperature = 240
 
 [filament:Fillamentum ASA 1.75mm]
 bed_temperature = 100
 bridge_fan_speed = 30
 compatible_printers = 
+compatible_printers_condition = 
 cooling = 0
 disable_fan_first_layers = 3
 end_filament_gcode = "; Filament-specific end gcode"
@@ -2853,13 +2889,14 @@ max_fan_speed = 30
 min_fan_speed = 10
 min_print_speed = 5
 slowdown_below_layer_time = 10
-start_filament_gcode = "M900 K{if printer_preset==\"Original Prusa i3 MK2 MultiMaterial\"}200{elsif printer_preset==\"Original Prusa i3 MK2 MM Single Mode\"}200{else}30{endif}; Filament gcode"
+start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}200{else}30{endif}; Filament gcode"
 temperature = 265
 
 [filament:Fillamentum CPE HG100 HM100]
 bed_temperature = 90
 bridge_fan_speed = 50
 compatible_printers = 
+compatible_printers_condition = 
 cooling = 1
 disable_fan_first_layers = 1
 end_filament_gcode = "; Filament-specific end gcode"
@@ -2881,13 +2918,14 @@ max_fan_speed = 80
 min_fan_speed = 80
 min_print_speed = 5
 slowdown_below_layer_time = 10
-start_filament_gcode = "M900 K{if printer_preset==\"Original Prusa i3 MK2 MultiMaterial\"}200{elsif printer_preset==\"Original Prusa i3 MK2 MM Single Mode\"}200{else}45{endif}; Filament gcode"
+start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}200{else}45{endif}; Filament gcode"
 temperature = 260
 
 [filament:Fillamentum Timberfil]
 bed_temperature = 60
 bridge_fan_speed = 100
-compatible_printers = "Original Prusa i3 MK2";"Original Prusa i3 MK2 0.6 nozzle";"Original Prusa i3 MK2 MM Single Mode";"Original Prusa i3 MK2 MM Single Mode 0.6 nozzle";"Original Prusa i3 MK2 MultiMaterial";"Original Prusa i3 MK2 MultiMaterial 0.6 nozzle";"Original Prusa i3 MK3"
+compatible_printers = 
+compatible_printers_condition = nozzle_diameter[0]>0.35
 cooling = 1
 disable_fan_first_layers = 1
 end_filament_gcode = "; Filament-specific end gcode"
@@ -2909,13 +2947,14 @@ max_fan_speed = 100
 min_fan_speed = 85
 min_print_speed = 15
 slowdown_below_layer_time = 10
-start_filament_gcode = "M900 K{if printer_preset==\"Original Prusa i3 MK2 MultiMaterial\"}200{elsif printer_preset==\"Original Prusa i3 MK2 MM Single Mode\"}200{else}10{endif}; Filament gcode"
+start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}200{else}10{endif}; Filament gcode"
 temperature = 190
 
 [filament:Generic ABS 1.75mm]
 bed_temperature = 100
 bridge_fan_speed = 30
 compatible_printers = 
+compatible_printers_condition = 
 cooling = 0
 disable_fan_first_layers = 3
 end_filament_gcode = "; Filament-specific end gcode"
@@ -2937,13 +2976,14 @@ max_fan_speed = 30
 min_fan_speed = 10
 min_print_speed = 5
 slowdown_below_layer_time = 10
-start_filament_gcode = "M900 K{if printer_preset==\"Original Prusa i3 MK2 MultiMaterial\"}200{elsif printer_preset==\"Original Prusa i3 MK2 MM Single Mode\"}200{else}30{endif}; Filament gcode"
+start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}200{else}30{endif}; Filament gcode"
 temperature = 255
 
 [filament:Generic PET 1.75mm]
 bed_temperature = 90
 bridge_fan_speed = 50
 compatible_printers = 
+compatible_printers_condition = 
 cooling = 1
 disable_fan_first_layers = 3
 end_filament_gcode = "; Filament-specific end gcode"
@@ -2965,13 +3005,14 @@ max_fan_speed = 50
 min_fan_speed = 30
 min_print_speed = 5
 slowdown_below_layer_time = 10
-start_filament_gcode = "M900 K{if printer_preset==\"Original Prusa i3 MK2 MultiMaterial\"}200{elsif printer_preset==\"Original Prusa i3 MK2 MM Single Mode\"}200{else}45{endif}; Filament gcode"
+start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}200{else}45{endif}; Filament gcode"
 temperature = 240
 
 [filament:Generic PLA 1.75mm]
 bed_temperature = 60
 bridge_fan_speed = 100
 compatible_printers = 
+compatible_printers_condition = 
 cooling = 1
 disable_fan_first_layers = 1
 end_filament_gcode = "; Filament-specific end gcode"
@@ -2993,13 +3034,14 @@ max_fan_speed = 100
 min_fan_speed = 85
 min_print_speed = 15
 slowdown_below_layer_time = 10
-start_filament_gcode = "M900 K{if printer_preset==\"Original Prusa i3 MK2 MultiMaterial\"}200{elsif printer_preset==\"Original Prusa i3 MK2 MM Single Mode\"}200{else}30{endif}; Filament gcode"
+start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}200{else}30{endif}; Filament gcode"
 temperature = 210
 
 [filament:Polymaker PC-Max]
 bed_temperature = 120
 bridge_fan_speed = 30
 compatible_printers = 
+compatible_printers_condition = 
 cooling = 0
 disable_fan_first_layers = 3
 end_filament_gcode = "; Filament-specific end gcode"
@@ -3021,13 +3063,14 @@ max_fan_speed = 30
 min_fan_speed = 10
 min_print_speed = 5
 slowdown_below_layer_time = 10
-start_filament_gcode = "M900 K{if printer_preset==\"Original Prusa i3 MK2 MultiMaterial\"}200{elsif printer_preset==\"Original Prusa i3 MK2 MM Single Mode\"}200{else}30{endif}; Filament gcode"
+start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}200{else}30{endif}; Filament gcode"
 temperature = 270
 
 [filament:Primavalue PVA]
 bed_temperature = 60
 bridge_fan_speed = 100
 compatible_printers = 
+compatible_printers_condition = 
 cooling = 0
 disable_fan_first_layers = 1
 end_filament_gcode = "; Filament-specific end gcode"
@@ -3049,13 +3092,14 @@ max_fan_speed = 100
 min_fan_speed = 85
 min_print_speed = 15
 slowdown_below_layer_time = 10
-start_filament_gcode = "M900 K{if printer_preset==\"Original Prusa i3 MK2 MultiMaterial\"}200{elsif printer_preset==\"Original Prusa i3 MK2 MM Single Mode\"}200{else}10{endif}; Filament gcode"
+start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}200{else}10{endif}; Filament gcode"
 temperature = 195
 
 [filament:Prusa ABS 1.75mm]
 bed_temperature = 100
 bridge_fan_speed = 30
 compatible_printers = 
+compatible_printers_condition = 
 cooling = 0
 disable_fan_first_layers = 3
 end_filament_gcode = "; Filament-specific end gcode"
@@ -3077,13 +3121,14 @@ max_fan_speed = 30
 min_fan_speed = 10
 min_print_speed = 5
 slowdown_below_layer_time = 10
-start_filament_gcode = "M900 K{if printer_preset==\"Original Prusa i3 MK2 MultiMaterial\"}200{elsif printer_preset==\"Original Prusa i3 MK2 MM Single Mode\"}200{else}30{endif}; Filament gcode"
+start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}200{else}30{endif}; Filament gcode"
 temperature = 255
 
 [filament:Prusa HIPS 1.75mm]
 bed_temperature = 100
 bridge_fan_speed = 50
 compatible_printers = 
+compatible_printers_condition = 
 cooling = 1
 disable_fan_first_layers = 3
 end_filament_gcode = "; Filament-specific end gcode"
@@ -3105,13 +3150,14 @@ max_fan_speed = 20
 min_fan_speed = 20
 min_print_speed = 5
 slowdown_below_layer_time = 10
-start_filament_gcode = "M900 K{if printer_preset==\"Original Prusa i3 MK2 MultiMaterial\"}200{elsif printer_preset==\"Original Prusa i3 MK2 MM Single Mode\"}200{else}10{endif}; Filament gcode"
+start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}200{else}10{endif}; Filament gcode"
 temperature = 220
 
 [filament:Prusa PET 1.75mm]
 bed_temperature = 90
 bridge_fan_speed = 50
 compatible_printers = 
+compatible_printers_condition = 
 cooling = 1
 disable_fan_first_layers = 3
 end_filament_gcode = "; Filament-specific end gcode"
@@ -3133,13 +3179,14 @@ max_fan_speed = 50
 min_fan_speed = 30
 min_print_speed = 5
 slowdown_below_layer_time = 10
-start_filament_gcode = "M900 K{if printer_preset==\"Original Prusa i3 MK2 MultiMaterial\"}200{elsif printer_preset==\"Original Prusa i3 MK2 MM Single Mode\"}200{else}45{endif}; Filament gcode"
+start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}200{else}45{endif}; Filament gcode"
 temperature = 240
 
 [filament:Prusa PLA 1.75mm]
 bed_temperature = 60
 bridge_fan_speed = 100
 compatible_printers = 
+compatible_printers_condition = 
 cooling = 1
 disable_fan_first_layers = 1
 end_filament_gcode = "; Filament-specific end gcode"
@@ -3161,13 +3208,14 @@ max_fan_speed = 100
 min_fan_speed = 85
 min_print_speed = 15
 slowdown_below_layer_time = 10
-start_filament_gcode = "M900 K{if printer_preset==\"Original Prusa i3 MK2 MultiMaterial\"}200{elsif printer_preset==\"Original Prusa i3 MK2 MM Single Mode\"}200{else}30{endif}; Filament gcode"
+start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}200{else}30{endif}; Filament gcode"
 temperature = 210
 
 [filament:SemiFlex or Flexfill 98A]
 bed_temperature = 50
 bridge_fan_speed = 100
-compatible_printers = "Original Prusa i3 MK2";"Original Prusa i3 MK2 0.6 nozzle";"Original Prusa i3 MK2 MM Single Mode";"Original Prusa i3 MK2 MM Single Mode 0.6 nozzle";"Original Prusa i3 MK3"
+compatible_printers = 
+compatible_printers_condition = nozzle_diameter[0]>0.35 and num_extruders==1
 cooling = 0
 disable_fan_first_layers = 1
 end_filament_gcode = "; Filament-specific end gcode"
@@ -3189,13 +3237,14 @@ max_fan_speed = 90
 min_fan_speed = 70
 min_print_speed = 5
 slowdown_below_layer_time = 10
-start_filament_gcode = "M900 K{if printer_preset==\"Original Prusa i3 MK2 MultiMaterial\"}200{elsif printer_preset==\"Original Prusa i3 MK2 MM Single Mode\"}200{else}10{endif}; Filament gcode"
+start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}200{else}10{endif}; Filament gcode"
 temperature = 230
 
 [filament:Taulman Bridge 1.75mm]
 bed_temperature = 50
 bridge_fan_speed = 40
 compatible_printers = 
+compatible_printers_condition = 
 cooling = 0
 disable_fan_first_layers = 3
 end_filament_gcode = "; Filament-specific end gcode"
@@ -3217,13 +3266,14 @@ max_fan_speed = 5
 min_fan_speed = 0
 min_print_speed = 5
 slowdown_below_layer_time = 10
-start_filament_gcode = "M900 K{if printer_preset==\"Original Prusa i3 MK2 MultiMaterial\"}200{elsif printer_preset==\"Original Prusa i3 MK2 MM Single Mode\"}200{else}10{endif}; Filament gcode"
+start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}200{else}10{endif}; Filament gcode"
 temperature = 250
 
 [filament:Taulman T-Glase 1.75mm]
 bed_temperature = 90
 bridge_fan_speed = 40
 compatible_printers = 
+compatible_printers_condition = 
 cooling = 0
 disable_fan_first_layers = 3
 end_filament_gcode = "; Filament-specific end gcode"
@@ -3245,13 +3295,14 @@ max_fan_speed = 5
 min_fan_speed = 0
 min_print_speed = 5
 slowdown_below_layer_time = 10
-start_filament_gcode = "M900 K{if printer_preset==\"Original Prusa i3 MK2 MultiMaterial\"}200{elsif printer_preset==\"Original Prusa i3 MK2 MM Single Mode\"}200{else}30{endif}; Filament gcode"
+start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}200{else}30{endif}; Filament gcode"
 temperature = 240
 
 [filament:Verbatim BVOH]
 bed_temperature = 60
 bridge_fan_speed = 100
 compatible_printers = 
+compatible_printers_condition = 
 cooling = 0
 disable_fan_first_layers = 1
 end_filament_gcode = "; Filament-specific end gcode"
@@ -3273,13 +3324,14 @@ max_fan_speed = 100
 min_fan_speed = 85
 min_print_speed = 15
 slowdown_below_layer_time = 10
-start_filament_gcode = "M900 K{if printer_preset==\"Original Prusa i3 MK2 MultiMaterial\"}200{elsif printer_preset==\"Original Prusa i3 MK2 MM Single Mode\"}200{else}10{endif}; Filament gcode"
+start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}200{else}10{endif}; Filament gcode"
 temperature = 210
 
 [filament:Verbatim PP]
 bed_temperature = 100
 bridge_fan_speed = 100
 compatible_printers = 
+compatible_printers_condition = 
 cooling = 1
 disable_fan_first_layers = 2
 end_filament_gcode = "; Filament-specific end gcode"
@@ -3301,7 +3353,7 @@ max_fan_speed = 100
 min_fan_speed = 100
 min_print_speed = 15
 slowdown_below_layer_time = 10
-start_filament_gcode = "M900 K{if printer_preset==\"Original Prusa i3 MK2 MultiMaterial\"}200{elsif printer_preset==\"Original Prusa i3 MK2 MM Single Mode\"}200{else}10{endif}; Filament gcode"
+start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}200{else}10{endif}; Filament gcode"
 temperature = 220
 
 [printer:Original Prusa i3 MK2]
@@ -3319,15 +3371,15 @@ min_layer_height = 0.07
 nozzle_diameter = 0.4
 octoprint_apikey = 
 octoprint_host = 
-printer_notes = 
+printer_notes = Don't remove the following keywords! These keywords are used in the "compatible printer" condition of the print and filament profiles to link the particular print and filament profiles to this printer profile.\nPRINTER_VENDOR_PRUSA3D\nPRINTER_MODEL_MK2\n
 printer_settings_id = 
 retract_before_travel = 1
 retract_before_wipe = 0%
 retract_layer_change = 1
 retract_length = 0.8
 retract_length_toolchange = 3
-retract_lift = 0.5
-retract_lift_above = 1
+retract_lift = 0.6
+retract_lift_above = 0
 retract_lift_below = 199
 retract_restart_extra = 0
 retract_restart_extra_toolchange = 0
@@ -3359,15 +3411,15 @@ min_layer_height = 0.05
 nozzle_diameter = 0.25
 octoprint_apikey = 
 octoprint_host = 
-printer_notes = 
+printer_notes = Don't remove the following keywords! These keywords are used in the "compatible printer" condition of the print and filament profiles to link the particular print and filament profiles to this printer profile.\nPRINTER_VENDOR_PRUSA3D\nPRINTER_MODEL_MK2\n
 printer_settings_id = 
 retract_before_travel = 1
 retract_before_wipe = 0%
 retract_layer_change = 1
 retract_length = 1
 retract_length_toolchange = 3
-retract_lift = 0.5
-retract_lift_above = 1
+retract_lift = 0.6
+retract_lift_above = 0
 retract_lift_below = 199
 retract_restart_extra = 0
 retract_restart_extra_toolchange = 0
@@ -3399,15 +3451,15 @@ min_layer_height = 0.1
 nozzle_diameter = 0.6
 octoprint_apikey = 
 octoprint_host = 
-printer_notes = 
+printer_notes = Don't remove the following keywords! These keywords are used in the "compatible printer" condition of the print and filament profiles to link the particular print and filament profiles to this printer profile.\nPRINTER_VENDOR_PRUSA3D\nPRINTER_MODEL_MK2\n
 printer_settings_id = 
 retract_before_travel = 1
 retract_before_wipe = 0%
 retract_layer_change = 1
 retract_length = 0.8
 retract_length_toolchange = 3
-retract_lift = 0.5
-retract_lift_above = 1
+retract_lift = 0.6
+retract_lift_above = 0
 retract_lift_below = 199
 retract_restart_extra = 0
 retract_restart_extra_toolchange = 0
@@ -3439,14 +3491,14 @@ min_layer_height = 0.07
 nozzle_diameter = 0.4
 octoprint_apikey = 
 octoprint_host = 
-printer_notes = 
+printer_notes = Don't remove the following keywords! These keywords are used in the "compatible printer" condition of the print and filament profiles to link the particular print and filament profiles to this printer profile.\nPRINTER_VENDOR_PRUSA3D\nPRINTER_MODEL_MK2\nPRINTER_HAS_BOWDEN
 printer_settings_id = 
 retract_before_travel = 3
 retract_before_wipe = 0%
 retract_layer_change = 0
 retract_length = 4
 retract_length_toolchange = 6
-retract_lift = 0.5
+retract_lift = 0.6
 retract_lift_above = 0
 retract_lift_below = 199
 retract_restart_extra = 0
@@ -3479,14 +3531,14 @@ min_layer_height = 0.07
 nozzle_diameter = 0.6
 octoprint_apikey = 
 octoprint_host = 
-printer_notes = 
+printer_notes = Don't remove the following keywords! These keywords are used in the "compatible printer" condition of the print and filament profiles to link the particular print and filament profiles to this printer profile.\nPRINTER_VENDOR_PRUSA3D\nPRINTER_MODEL_MK2\nPRINTER_HAS_BOWDEN
 printer_settings_id = 
 retract_before_travel = 3
 retract_before_wipe = 0%
 retract_layer_change = 0
 retract_length = 4
 retract_length_toolchange = 6
-retract_lift = 0.5
+retract_lift = 0.6
 retract_lift_above = 0
 retract_lift_below = 199
 retract_restart_extra = 0
@@ -3519,14 +3571,14 @@ min_layer_height = 0.07,0.07,0.07,0.07
 nozzle_diameter = 0.4,0.4,0.4,0.4
 octoprint_apikey = 
 octoprint_host = 
-printer_notes = 
+printer_notes = Don't remove the following keywords! These keywords are used in the "compatible printer" condition of the print and filament profiles to link the particular print and filament profiles to this printer profile.\nPRINTER_VENDOR_PRUSA3D\nPRINTER_MODEL_MK2\nPRINTER_HAS_BOWDEN
 printer_settings_id = 
 retract_before_travel = 3,3,3,3
 retract_before_wipe = 60%,60%,60%,60%
 retract_layer_change = 0,0,0,0
 retract_length = 4,4,4,4
 retract_length_toolchange = 4,4,4,4
-retract_lift = 0.5,0.5,0.5,0.5
+retract_lift = 0.6,0.6,0.6,0.6
 retract_lift_above = 0,0,0,0
 retract_lift_below = 199,199,199,199
 retract_restart_extra = 0,0,0,0
@@ -3559,14 +3611,14 @@ min_layer_height = 0.07,0.07,0.07,0.07
 nozzle_diameter = 0.6,0.6,0.6,0.6
 octoprint_apikey = 
 octoprint_host = 
-printer_notes = 
+printer_notes = Don't remove the following keywords! These keywords are used in the "compatible printer" condition of the print and filament profiles to link the particular print and filament profiles to this printer profile.\nPRINTER_VENDOR_PRUSA3D\nPRINTER_MODEL_MK2\nPRINTER_HAS_BOWDEN
 printer_settings_id = 
 retract_before_travel = 3,3,3,3
 retract_before_wipe = 60%,60%,60%,60%
 retract_layer_change = 0,0,0,0
 retract_length = 4,4,4,4
 retract_length_toolchange = 4,4,4,4
-retract_lift = 0.5,0.5,0.5,0.5
+retract_lift = 0.6,0.6,0.6,0.6
 retract_lift_above = 0,0,0,0
 retract_lift_below = 199,199,199,199
 retract_restart_extra = 0,0,0,0
@@ -3599,22 +3651,22 @@ min_layer_height = 0.07
 nozzle_diameter = 0.4
 octoprint_apikey = 
 octoprint_host = 
-printer_notes = 
+printer_notes = Don't remove the following keywords! These keywords are used in the "compatible printer" condition of the print and filament profiles to link the particular print and filament profiles to this printer profile.\nPRINTER_VENDOR_PRUSA3D\nPRINTER_MODEL_MK3\n
 retract_before_travel = 1
 retract_before_wipe = 0%
 retract_layer_change = 1
 retract_length = 0.8
 retract_length_toolchange = 3
-retract_lift = 0.5
-retract_lift_above = 1
-retract_lift_below = 199
+retract_lift = 0.6
+retract_lift_above = 0
+retract_lift_below = 209
 retract_restart_extra = 0
 retract_restart_extra_toolchange = 0
 retract_speed = 35
 serial_port = 
 serial_speed = 250000
 single_extruder_multi_material = 0
-start_gcode = M115 U3.1.0 ; tell printer latest fw version\nM83  ; extruder relative mode\nM104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nG28 W ; home all without mesh bed level\nG80 ; mesh bed leveling\nG1 Y-3.0 F1000.0 ; go outside pritn area\nG1 X60.0 E9.0  F1000.0 ; intro line\nG1 X100.0 E12.5  F1000.0 ; intro line
+start_gcode = M115 U3.1.0 ; tell printer latest fw version\nM83  ; extruder relative mode\nM104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nG28 W ; home all without mesh bed level\nG80 ; mesh bed leveling\nG1 Y-3.0 F1000.0 ; go outside print area\nG92 E0.0\nG1 X60.0 E9.0  F1000.0 ; intro line\nG1 X100.0 E12.5  F1000.0 ; intro line\nG92 E0.0
 toolchange_gcode = 
 use_firmware_retraction = 0
 use_relative_e_distances = 1