diff options
author | Dan Murphy <dmurphy@ti.com> | 2019-03-21 17:28:35 +0300 |
---|---|---|
committer | Jacek Anaszewski <jacek.anaszewski@gmail.com> | 2019-04-07 21:45:48 +0300 |
commit | 6ccc7435fab7cc4f158440b086105c263b62a36f (patch) | |
tree | ed9454e4a7c1525a4a14b01c5d6f1dbecc56f824 /Documentation/devicetree/bindings/leds | |
parent | 9e98c678c2d6ae3a17cb2de55d17f69dddaa231b (diff) |
dt: lm3532: Add lm3532 dt doc and update ti_lmu doc
Add the lm3532 device tree documentation.
Remove lm3532 device tree reference from the ti_lmu devicetree
documentation.
With the addition of the dedicated lm3532 documentation the device
can be removed from the ti_lmu.txt.
The reason for this is that the lm3532 dt documentation now defines
the ability to control LED output strings against different control
banks or groups multiple strings to be controlled by a single control
bank.
Another addition was for ALS lighting control and configuration. The
LM3532 has a feature that can take in the ALS reading from 2 separate
ALS devices and adjust the brightness on the strings that are configured
to support this feature.
Finally the device specific properties were moved to the parent node
as these properties are not control bank configurable. These include
the runtime ramp and the ALS configuration.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-for-MFD-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Diffstat (limited to 'Documentation/devicetree/bindings/leds')
-rw-r--r-- | Documentation/devicetree/bindings/leds/leds-lm3532.txt | 101 |
1 files changed, 101 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/leds/leds-lm3532.txt b/Documentation/devicetree/bindings/leds/leds-lm3532.txt new file mode 100644 index 000000000000..c087f85ddddc --- /dev/null +++ b/Documentation/devicetree/bindings/leds/leds-lm3532.txt @@ -0,0 +1,101 @@ +* Texas Instruments - lm3532 White LED driver with ambient light sensing +capability. + +The LM3532 provides the 3 high-voltage, low-side current sinks. The device is +programmable over an I2C-compatible interface and has independent +current control for all three channels. The adaptive current regulation +method allows for different LED currents in each current sink thus allowing +for a wide variety of backlight and keypad applications. + +The main features of the LM3532 include dual ambient light sensor inputs +each with 32 internal voltage setting resistors, 8-bit logarithmic and linear +brightness control, dual external PWM brightness control inputs, and up to +1000:1 dimming ratio with programmable fade in and fade out settings. + +Required properties: + - compatible : "ti,lm3532" + - reg : I2C slave address + - #address-cells : 1 + - #size-cells : 0 + +Optional properties: + - enable-gpios : gpio pin to enable (active high)/disable the device. + - ramp-up-us - The Run time ramp rates/step are from one current + set-point to another after the device has reached its + initial target set point from turn-on + - ramp-down-us - The Run time ramp rates/step are from one current + set-point to another after the device has reached its + initial target set point from turn-on + Range for ramp settings: 8us - 65536us + +Optional properties if ALS mode is used: + - ti,als-vmin - Minimum ALS voltage defined in Volts + - ti,als-vmax - Maximum ALS voltage defined in Volts + Per the data sheet the max ALS voltage is 2V and the min is 0V + + - ti,als1-imp-sel - ALS1 impedance resistor selection in Ohms + - ti,als2-imp-sel - ALS2 impedance resistor selection in Ohms + Range for impedance select: 37000 Ohms - 1190 Ohms + Values above 37kohms will be set to the "High Impedance" setting + + - ti,als-avrg-time-us - Determines the length of time the device needs to + average the two ALS inputs. This is only used if + the input mode is LM3532_ALS_INPUT_AVRG. + Range: 17920us - 2293760us + - ti,als-input-mode - Determines how the device uses the attached ALS + devices. + 0x00 - ALS1 and ALS2 input average + 0x01 - ALS1 Input + 0x02 - ALS2 Input + 0x03 - Max of ALS1 and ALS2 + +Required child properties: + - reg : Indicates control bank the LED string is controlled by + - led-sources : see Documentation/devicetree/bindings/leds/common.txt + - ti,led-mode : Defines if the LED strings are manually controlled or + if the LED strings are controlled by the ALS. + 0x00 - LED strings are I2C controlled via full scale + brightness control register + 0x01 - LED strings are ALS controlled + +Optional LED child properties: + - label : see Documentation/devicetree/bindings/leds/common.txt + - linux,default-trigger : + see Documentation/devicetree/bindings/leds/common.txt + +Example: +led-controller@38 { + compatible = "ti,lm3532"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x38>; + + enable-gpios = <&gpio6 12 GPIO_ACTIVE_HIGH>; + ramp-up-us = <1024>; + ramp-down-us = <65536>; + + ti,als-vmin = <0>; + ti,als-vmax = <2000>; + ti,als1-imp-sel = <4110>; + ti,als2-imp-sel = <2180>; + ti,als-avrg-time-us = <17920>; + ti,als-input-mode = <0x00>; + + led@0 { + reg = <0>; + led-sources = <2>; + ti,led-mode = <1>; + label = ":backlight"; + linux,default-trigger = "backlight"; + }; + + led@1 { + reg = <1>; + led-sources = <1>; + ti,led-mode = <0>; + label = ":kbd_backlight"; + }; +}; + +For more product information please see the links below: +http://www.ti.com/product/LM3532 |