Merge tag 'arm-drivers-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc

Pull ARM driver updates from Arnd Bergmann:
 "There are a few separately maintained driver subsystems that we merge
  through the SoC tree, notable changes are:

   - Memory controller updates, mainly for Tegra and Mediatek SoCs, and
     clarifications for the memory controller DT bindings

   - SCMI firmware interface updates, in particular a new transport
     based on OPTEE and support for atomic operations.

   - Cleanups to the TEE subsystem, refactoring its memory management

  For SoC specific drivers without a separate subsystem, changes include

   - Smaller updates and fixes for TI, AT91/SAMA5, Qualcomm and NXP
     Layerscape SoCs.

   - Driver support for Microchip SAMA5D29, Tesla FSD, Renesas RZ/G2L,
     and Qualcomm SM8450.

   - Better power management on Mediatek MT81xx, NXP i.MX8MQ and older
     NVIDIA Tegra chips"

* tag 'arm-drivers-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (154 commits)
  ARM: spear: fix typos in comments
  soc/microchip: fix invalid free in mpfs_sys_controller_delete
  soc: s4: Add support for power domains controller
  dt-bindings: power: add Amlogic s4 power domains bindings
  ARM: at91: add support in soc driver for new SAMA5D29
  soc: mediatek: mmsys: add sw0_rst_offset in mmsys driver data
  dt-bindings: memory: renesas,rpc-if: Document RZ/V2L SoC
  memory: emif: check the pointer temp in get_device_details()
  memory: emif: Add check for setup_interrupts
  dt-bindings: arm: mediatek: mmsys: add support for MT8186
  dt-bindings: mediatek: add compatible for MT8186 pwrap
  soc: mediatek: pwrap: add pwrap driver for MT8186 SoC
  soc: mediatek: mmsys: add mmsys reset control for MT8186
  soc: mediatek: mtk-infracfg: Disable ACP on MT8192
  soc: ti: k3-socinfo: Add AM62x JTAG ID
  soc: mediatek: add MTK mutex support for MT8186
  soc: mediatek: mmsys: add mt8186 mmsys routing table
  soc: mediatek: pm-domains: Add support for mt8186
  dt-bindings: power: Add MT8186 power domains
  soc: mediatek: pm-domains: Add support for mt8195
  ...

22 files changed, 1012 insertions, 335 deletions

diff --git a/Documentation/devicetree/bindings/arm/mediatek/mediatek,mmsys.yaml b/Documentation/devicetree/bindings/arm/mediatek/mediatek,mmsys.yaml
index 763c62323a74..b31d90dc9eb4 100644
--- a/Documentation/devicetree/bindings/arm/mediatek/mediatek,mmsys.yaml
+++ b/Documentation/devicetree/bindings/arm/mediatek/mediatek,mmsys.yaml
@@ -29,6 +29,7 @@ properties:
               - mediatek,mt8167-mmsys
               - mediatek,mt8173-mmsys
               - mediatek,mt8183-mmsys
+              - mediatek,mt8186-mmsys
               - mediatek,mt8192-mmsys
               - mediatek,mt8365-mmsys
           - const: syscon
diff --git a/Documentation/devicetree/bindings/arm/msm/qcom,llcc.yaml b/Documentation/devicetree/bindings/arm/msm/qcom,llcc.yaml
index 03882aac8d2d..30fcbe2ad8a3 100644
--- a/Documentation/devicetree/bindings/arm/msm/qcom,llcc.yaml
+++ b/Documentation/devicetree/bindings/arm/msm/qcom,llcc.yaml
@@ -27,6 +27,8 @@ properties:
       - qcom,sm6350-llcc
       - qcom,sm8150-llcc
       - qcom,sm8250-llcc
+      - qcom,sm8350-llcc
+      - qcom,sm8450-llcc
 
   reg:
     items:
diff --git a/Documentation/devicetree/bindings/clock/tesla,fsd-clock.yaml b/Documentation/devicetree/bindings/clock/tesla,fsd-clock.yaml
new file mode 100644
index 000000000000..dc808e2f8327
--- /dev/null
+++ b/Documentation/devicetree/bindings/clock/tesla,fsd-clock.yaml
@@ -0,0 +1,198 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/clock/tesla,fsd-clock.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Tesla FSD (Full Self-Driving) SoC clock controller
+
+maintainers:
+  - Alim Akhtar <alim.akhtar@samsung.com>
+  - linux-fsd@tesla.com
+
+description: |
+  FSD clock controller consist of several clock management unit
+  (CMU), which generates clocks for various inteernal SoC blocks.
+  The root clock comes from external OSC clock (24 MHz).
+
+  All available clocks are defined as preprocessor macros in
+  'dt-bindings/clock/fsd-clk.h' header.
+
+properties:
+  compatible:
+    enum:
+      - tesla,fsd-clock-cmu
+      - tesla,fsd-clock-imem
+      - tesla,fsd-clock-peric
+      - tesla,fsd-clock-fsys0
+      - tesla,fsd-clock-fsys1
+      - tesla,fsd-clock-mfc
+      - tesla,fsd-clock-cam_csi
+
+  clocks:
+    minItems: 1
+    maxItems: 6
+
+  clock-names:
+    minItems: 1
+    maxItems: 6
+
+  "#clock-cells":
+    const: 1
+
+  reg:
+    maxItems: 1
+
+allOf:
+  - if:
+      properties:
+        compatible:
+          contains:
+            const: tesla,fsd-clock-cmu
+    then:
+      properties:
+        clocks:
+          items:
+            - description: External reference clock (24 MHz)
+        clock-names:
+          items:
+            - const: fin_pll
+
+  - if:
+      properties:
+        compatible:
+          contains:
+            const: tesla,fsd-clock-imem
+    then:
+      properties:
+        clocks:
+          items:
+            - description: External reference clock (24 MHz)
+            - description: IMEM TCU clock (from CMU_CMU)
+            - description: IMEM bus clock (from CMU_CMU)
+            - description: IMEM DMA clock (from CMU_CMU)
+        clock-names:
+          items:
+            - const: fin_pll
+            - const: dout_cmu_imem_tcuclk
+            - const: dout_cmu_imem_aclk
+            - const: dout_cmu_imem_dmaclk
+
+  - if:
+      properties:
+        compatible:
+          contains:
+            const: tesla,fsd-clock-peric
+    then:
+      properties:
+        clocks:
+          items:
+            - description: External reference clock (24 MHz)
+            - description: Shared0 PLL div4 clock (from CMU_CMU)
+            - description: PERIC shared1 div36 clock (from CMU_CMU)
+            - description: PERIC shared0 div3 TBU clock (from CMU_CMU)
+            - description: PERIC shared0 div20 clock (from CMU_CMU)
+            - description: PERIC shared1 div4 DMAclock (from CMU_CMU)
+        clock-names:
+          items:
+            - const: fin_pll
+            - const: dout_cmu_pll_shared0_div4
+            - const: dout_cmu_peric_shared1div36
+            - const: dout_cmu_peric_shared0div3_tbuclk
+            - const: dout_cmu_peric_shared0div20
+            - const: dout_cmu_peric_shared1div4_dmaclk
+
+  - if:
+      properties:
+        compatible:
+          contains:
+            const: tesla,fsd-clock-fsys0
+    then:
+      properties:
+        clocks:
+          items:
+            - description: External reference clock (24 MHz)
+            - description: Shared0 PLL div6 clock (from CMU_CMU)
+            - description: FSYS0 shared1 div4 clock (from CMU_CMU)
+            - description: FSYS0 shared0 div4 clock (from CMU_CMU)
+        clock-names:
+          items:
+            - const: fin_pll
+            - const: dout_cmu_pll_shared0_div6
+            - const: dout_cmu_fsys0_shared1div4
+            - const: dout_cmu_fsys0_shared0div4
+
+  - if:
+      properties:
+        compatible:
+          contains:
+            const: tesla,fsd-clock-fsys1
+    then:
+      properties:
+        clocks:
+          items:
+            - description: External reference clock (24 MHz)
+            - description: FSYS1 shared0 div8 clock (from CMU_CMU)
+            - description: FSYS1 shared0 div4 clock (from CMU_CMU)
+        clock-names:
+          items:
+            - const: fin_pll
+            - const: dout_cmu_fsys1_shared0div8
+            - const: dout_cmu_fsys1_shared0div4
+
+  - if:
+      properties:
+        compatible:
+          contains:
+            const: tesla,fsd-clock-mfc
+    then:
+      properties:
+        clocks:
+          items:
+            - description: External reference clock (24 MHz)
+        clock-names:
+          items:
+            - const: fin_pll
+
+  - if:
+      properties:
+        compatible:
+          contains:
+            const: tesla,fsd-clock-cam_csi
+    then:
+      properties:
+        clocks:
+          items:
+            - description: External reference clock (24 MHz)
+        clock-names:
+          items:
+            - const: fin_pll
+
+required:
+  - compatible
+  - "#clock-cells"
+  - clocks
+  - clock-names
+  - reg
+
+additionalProperties: false
+
+examples:
+  # Clock controller node for CMU_FSYS1
+  - |
+    #include <dt-bindings/clock/fsd-clk.h>
+
+    clock_fsys1: clock-controller@16810000 {
+          compatible = "tesla,fsd-clock-fsys1";
+          reg = <0x16810000 0x3000>;
+          #clock-cells = <1>;
+
+          clocks = <&fin_pll>,
+                   <&clock_cmu DOUT_CMU_FSYS1_SHARED0DIV8>,
+                   <&clock_cmu DOUT_CMU_FSYS1_SHARED0DIV4>;
+          clock-names = "fin_pll",
+                        "dout_cmu_fsys1_shared0div8",
+                        "dout_cmu_fsys1_shared0div4";
+    };
+
+...
diff --git a/Documentation/devicetree/bindings/firmware/arm,scmi.yaml b/Documentation/devicetree/bindings/firmware/arm,scmi.yaml
index 5c4c6782e052..590743883802 100644
--- a/Documentation/devicetree/bindings/firmware/arm,scmi.yaml
+++ b/Documentation/devicetree/bindings/firmware/arm,scmi.yaml
@@ -38,6 +38,9 @@ properties:
                      The virtio transport only supports a single device.
         items:
           - const: arm,scmi-virtio
+      - description: SCMI compliant firmware with OP-TEE transport
+        items:
+          - const: linaro,scmi-optee
 
   interrupts:
     description:
@@ -78,11 +81,24 @@ properties:
   '#size-cells':
     const: 0
 
+  atomic-threshold-us:
+    description:
+      An optional time value, expressed in microseconds, representing, on this
+      platform, the threshold above which any SCMI command, advertised to have
+      an higher-than-threshold execution latency, should not be considered for
+      atomic mode of operation, even if requested.
+    default: 0
+
   arm,smc-id:
     $ref: /schemas/types.yaml#/definitions/uint32
     description:
       SMC id required when using smc or hvc transports
 
+  linaro,optee-channel-id:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description:
+      Channel specifier required when using OP-TEE transport.
+
   protocol@11:
     type: object
     properties:
@@ -195,6 +211,12 @@ patternProperties:
         minItems: 1
         maxItems: 2
 
+      linaro,optee-channel-id:
+        $ref: /schemas/types.yaml#/definitions/uint32
+        description:
+          Channel specifier required when using OP-TEE transport and
+          protocol has a dedicated communication channel.
+
     required:
       - reg
 
@@ -226,6 +248,16 @@ else:
       - arm,smc-id
       - shmem
 
+  else:
+    if:
+      properties:
+        compatible:
+          contains:
+            const: linaro,scmi-optee
+    then:
+      required:
+        - linaro,optee-channel-id
+
 examples:
   - |
     firmware {
@@ -240,6 +272,8 @@ examples:
             #address-cells = <1>;
             #size-cells = <0>;
 
+            atomic-threshold-us = <10000>;
+
             scmi_devpd: protocol@11 {
                 reg = <0x11>;
                 #power-domain-cells = <1>;
@@ -340,7 +374,48 @@ examples:
                 reg = <0x11>;
                 #power-domain-cells = <1>;
             };
+        };
+    };
+
+  - |
+    firmware {
+        scmi {
+            compatible = "linaro,scmi-optee";
+            linaro,optee-channel-id = <0>;
 
+            #address-cells = <1>;
+            #size-cells = <0>;
+
+            scmi_dvfs1: protocol@13 {
+                reg = <0x13>;
+                linaro,optee-channel-id = <1>;
+                shmem = <&cpu_optee_lpri0>;
+                #clock-cells = <1>;
+            };
+
+            scmi_clk0: protocol@14 {
+                reg = <0x14>;
+                #clock-cells = <1>;
+            };
+        };
+    };
+
+    soc {
+        #address-cells = <2>;
+        #size-cells = <2>;
+
+        sram@51000000 {
+            compatible = "mmio-sram";
+            reg = <0x0 0x51000000 0x0 0x10000>;
+
+            #address-cells = <1>;
+            #size-cells = <1>;
+            ranges = <0 0x0 0x51000000 0x10000>;
+
+            cpu_optee_lpri0: optee-sram-section@0 {
+                compatible = "arm,scmi-shmem";
+                reg = <0x0 0x80>;
+            };
         };
     };
 
diff --git a/Documentation/devicetree/bindings/memory-controllers/ddr/jedec,lpddr2-timings.yaml b/Documentation/devicetree/bindings/memory-controllers/ddr/jedec,lpddr2-timings.yaml
new file mode 100644
index 000000000000..f3e62ee07126
--- /dev/null
+++ b/Documentation/devicetree/bindings/memory-controllers/ddr/jedec,lpddr2-timings.yaml
@@ -0,0 +1,135 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/memory-controllers/ddr/jedec,lpddr2-timings.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: LPDDR2 SDRAM AC timing parameters for a given speed-bin
+
+maintainers:
+  - Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
+
+properties:
+  compatible:
+    const: jedec,lpddr2-timings
+
+  max-freq:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description: |
+      Maximum DDR clock frequency for the speed-bin, in Hz.
+
+  min-freq:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description: |
+      Minimum DDR clock frequency for the speed-bin, in Hz.
+
+  tCKESR:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description: |
+      CKE minimum pulse width during SELF REFRESH (low pulse width during
+      SELF REFRESH) in pico seconds.
+
+  tDQSCK-max:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description: |
+      DQS output data access time from CK_t/CK_c in pico seconds.
+
+  tDQSCK-max-derated:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description: |
+      DQS output data access time from CK_t/CK_c, temperature de-rated, in pico
+      seconds.
+
+  tFAW:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description: |
+      Four-bank activate window in pico seconds.
+
+  tRAS-max-ns:
+    description: |
+      Row active time in nano seconds.
+
+  tRAS-min:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description: |
+      Row active time in pico seconds.
+
+  tRCD:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description: |
+      RAS-to-CAS delay in pico seconds.
+
+  tRPab:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description: |
+      Row precharge time (all banks) in pico seconds.
+
+  tRRD:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description: |
+      Active bank A to active bank B in pico seconds.
+
+  tRTP:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description: |
+      Internal READ to PRECHARGE command delay in pico seconds.
+
+  tWR:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description: |
+      WRITE recovery time in pico seconds.
+
+  tWTR:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description: |
+      Internal WRITE-to-READ command delay in pico seconds.
+
+  tXP:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description: |
+      Exit power-down to next valid command delay in pico seconds.
+
+  tZQCL:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description: |
+      Long calibration time in pico seconds.
+
+  tZQCS:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description: |
+      Short calibration time in pico seconds.
+
+  tZQinit:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description: |
+      Initialization calibration time in pico seconds.
+
+required:
+  - compatible
+  - min-freq
+  - max-freq
+
+additionalProperties: false
+
+examples:
+  - |
+    timings {
+        compatible = "jedec,lpddr2-timings";
+        min-freq = <10000000>;
+        max-freq = <400000000>;
+        tCKESR = <15000>;
+        tDQSCK-max = <5500>;
+        tFAW = <50000>;
+        tRAS-max-ns = <70000>;
+        tRAS-min = <42000>;
+        tRPab = <21000>;
+        tRCD = <18000>;
+        tRRD = <10000>;
+        tRTP = <7500>;
+        tWR = <15000>;
+        tWTR = <7500>;
+        tXP = <7500>;
+        tZQCL = <360000>;
+        tZQCS = <90000>;
+        tZQinit = <1000000>;
+    };
diff --git a/Documentation/devicetree/bindings/memory-controllers/ddr/jedec,lpddr2.yaml b/Documentation/devicetree/bindings/memory-controllers/ddr/jedec,lpddr2.yaml
index 25ed0266f6dd..dd2141cad866 100644
--- a/Documentation/devicetree/bindings/memory-controllers/ddr/jedec,lpddr2.yaml
+++ b/Documentation/devicetree/bindings/memory-controllers/ddr/jedec,lpddr2.yaml
@@ -30,12 +30,26 @@ properties:
     maximum: 255
     description: |
       Revision 1 value of SDRAM chip. Obtained from device datasheet.
+      Property is deprecated, use revision-id instead.
+    deprecated: true
 
   revision-id2:
     $ref: /schemas/types.yaml#/definitions/uint32
     maximum: 255
     description: |
       Revision 2 value of SDRAM chip. Obtained from device datasheet.
+      Property is deprecated, use revision-id instead.
+    deprecated: true
+
+  revision-id:
+    $ref: /schemas/types.yaml#/definitions/uint32-array
+    description: |
+      Revision IDs read from Mode Register 6 and 7. One byte per uint32 cell (i.e. <MR6 MR7>).
+    minItems: 2
+    maxItems: 2
+    items:
+      minimum: 0
+      maximum: 255
 
   density:
     $ref: /schemas/types.yaml#/definitions/uint32
@@ -142,14 +156,12 @@ properties:
 
 patternProperties:
   "^lpddr2-timings":
-    type: object
+    $ref: jedec,lpddr2-timings.yaml
     description: |
       The lpddr2 node may have one or more child nodes of type "lpddr2-timings".
       "lpddr2-timings" provides AC timing parameters of the device for
       a given speed-bin. The user may provide the timings for as many
-      speed-bins as is required. Please see Documentation/devicetree/
-      bindings/memory-controllers/ddr/lpddr2-timings.txt for more information
-      on "lpddr2-timings".
+      speed-bins as is required.
 
 required:
   - compatible
@@ -164,8 +176,7 @@ examples:
         compatible = "elpida,ECB240ABACN", "jedec,lpddr2-s4";
         density = <2048>;
         io-width = <32>;
-        revision-id1 = <1>;
-        revision-id2 = <0>;
+        revision-id = <1 0>;
 
         tRPab-min-tck = <3>;
         tRCD-min-tck = <3>;
diff --git a/Documentation/devicetree/bindings/memory-controllers/ddr/jedec,lpddr3-timings.yaml b/Documentation/devicetree/bindings/memory-controllers/ddr/jedec,lpddr3-timings.yaml
new file mode 100644
index 000000000000..97c3e988af5f
--- /dev/null
+++ b/Documentation/devicetree/bindings/memory-controllers/ddr/jedec,lpddr3-timings.yaml
@@ -0,0 +1,157 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/memory-controllers/ddr/jedec,lpddr3-timings.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: LPDDR3 SDRAM AC timing parameters for a given speed-bin
+
+maintainers:
+  - Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
+
+properties:
+  compatible:
+    const: jedec,lpddr3-timings
+
+  reg:
+    maxItems: 1
+    description: |
+      Maximum DDR clock frequency for the speed-bin, in Hz.
+      Property is deprecated, use max-freq.
+    deprecated: true
+
+  max-freq:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description: |
+      Maximum DDR clock frequency for the speed-bin, in Hz.
+
+  min-freq:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description: |
+      Minimum DDR clock frequency for the speed-bin, in Hz.
+
+  tCKE:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description: |
+      CKE minimum pulse width (HIGH and LOW pulse width) in pico seconds.
+
+  tCKESR:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description: |
+      CKE minimum pulse width during SELF REFRESH (low pulse width during
+      SELF REFRESH) in pico seconds.
+
+  tFAW:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description: |
+      Four-bank activate window in pico seconds.
+
+  tMRD:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description: |
+      Mode register set command delay in pico seconds.
+
+  tR2R-C2C:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description: |
+      Additional READ-to-READ delay in chip-to-chip cases in pico seconds.
+
+  tRAS:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description: |
+      Row active time in pico seconds.
+
+  tRC:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description: |
+      ACTIVATE-to-ACTIVATE command period in pico seconds.
+
+  tRCD:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description: |
+      RAS-to-CAS delay in pico seconds.
+
+  tRFC:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description: |
+      Refresh Cycle time in pico seconds.
+
+  tRPab:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description: |
+      Row precharge time (all banks) in pico seconds.
+
+  tRPpb:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description: |
+      Row precharge time (single banks) in pico seconds.
+
+  tRRD:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description: |
+      Active bank A to active bank B in pico seconds.
+
+  tRTP:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description: |
+      Internal READ to PRECHARGE command delay in pico seconds.
+
+  tW2W-C2C:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description: |
+      Additional WRITE-to-WRITE delay in chip-to-chip cases in pico seconds.
+
+  tWR:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description: |
+      WRITE recovery time in pico seconds.
+
+  tWTR:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description: |
+      Internal WRITE-to-READ command delay in pico seconds.
+
+  tXP:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description: |
+      Exit power-down to next valid command delay in pico seconds.
+
+  tXSR:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description: |
+      SELF REFRESH exit to next valid command delay in pico seconds.
+
+required:
+  - compatible
+  - min-freq
+  - max-freq
+
+additionalProperties: false
+
+examples:
+  - |
+    lpddr3 {
+        timings {
+            compatible = "jedec,lpddr3-timings";
+            max-freq = <800000000>;
+            min-freq = <100000000>;
+            tCKE = <3750>;
+            tCKESR = <3750>;
+            tFAW = <25000>;
+            tMRD = <7000>;
+            tR2R-C2C = <0>;
+            tRAS = <23000>;
+            tRC = <33750>;
+            tRCD = <10000>;
+            tRFC = <65000>;
+            tRPab = <12000>;
+            tRPpb = <12000>;
+            tRRD = <6000>;
+            tRTP = <3750>;
+            tW2W-C2C = <0>;
+            tWR = <7500>;
+            tWTR = <3750>;
+            tXP = <3750>;
+            tXSR = <70000>;
+        };
+    };
diff --git a/Documentation/devicetree/bindings/memory-controllers/ddr/jedec,lpddr3.yaml b/Documentation/devicetree/bindings/memory-controllers/ddr/jedec,lpddr3.yaml
new file mode 100644
index 000000000000..c542f32c39fa
--- /dev/null
+++ b/Documentation/devicetree/bindings/memory-controllers/ddr/jedec,lpddr3.yaml
@@ -0,0 +1,263 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/memory-controllers/ddr/jedec,lpddr3.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: LPDDR3 SDRAM compliant to JEDEC JESD209-3
+
+maintainers:
+  - Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
+
+properties:
+  compatible:
+    items:
+      - enum:
+          - samsung,K3QF2F20DB
+      - const: jedec,lpddr3
+
+  '#address-cells':
+    const: 1
+    deprecated: true
+
+  density:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description: |
+      Density in megabits of SDRAM chip.
+    enum:
+      - 4096
+      - 8192
+      - 16384
+      - 32768
+
+  io-width:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description: |
+      IO bus width in bits of SDRAM chip.
+    enum:
+      - 32
+      - 16
+
+  manufacturer-id:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description: |
+      Manufacturer ID value read from Mode Register 5.  The property is
+      deprecated, manufacturer should be derived from the compatible.
+    deprecated: true
+
+  revision-id:
+    $ref: /schemas/types.yaml#/definitions/uint32-array
+    minItems: 2
+    maxItems: 2
+    items:
+      maximum: 255
+    description: |
+      Revision value of SDRAM chip read from Mode Registers 6 and 7.
+
+  '#size-cells':
+    const: 0
+    deprecated: true
+
+  tCKE-min-tck:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    maximum: 15
+    description: |
+      CKE minimum pulse width (HIGH and LOW pulse width) in terms of number
+      of clock cycles.
+
+  tCKESR-min-tck:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    maximum: 15
+    description: |
+      CKE minimum pulse width during SELF REFRESH (low pulse width during
+      SELF REFRESH) in terms of number of clock cycles.
+
+  tDQSCK-min-tck:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    maximum: 15
+    description: |
+      DQS output data access time from CK_t/CK_c in terms of number of clock
+      cycles.
+
+  tFAW-min-tck:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    maximum: 63
+    description: |
+      Four-bank activate window in terms of number of clock cycles.
+
+  tMRD-min-tck:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    maximum: 15
+    description: |
+      Mode register set command delay in terms of number of clock cycles.
+
+  tR2R-C2C-min-tck:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    enum: [0, 1]
+    description: |
+      Additional READ-to-READ delay in chip-to-chip cases in terms of number
+      of clock cycles.
+
+  tRAS-min-tck:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    maximum: 63
+    description: |
+      Row active time in terms of number of clock cycles.
+
+  tRC-min-tck:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    maximum: 63
+    description: |
+      ACTIVATE-to-ACTIVATE command period in terms of number of clock cycles.
+
+  tRCD-min-tck:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    maximum: 15
+    description: |
+      RAS-to-CAS delay in terms of number of clock cycles.
+
+  tRFC-min-tck:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    maximum: 255
+    description: |
+      Refresh Cycle time in terms of number of clock cycles.
+
+  tRL-min-tck:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    maximum: 15
+    description: |
+     READ data latency in terms of number of clock cycles.
+
+  tRPab-min-tck:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    maximum: 15
+    description: |
+      Row precharge time (all banks) in terms of number of clock cycles.
+
+  tRPpb-min-tck:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    maximum: 15
+    description: |
+      Row precharge time (single banks) in terms of number of clock cycles.
+
+  tRRD-min-tck:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    maximum: 15
+    description: |
+      Active bank A to active bank B in terms of number of clock cycles.
+
+  tRTP-min-tck:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    maximum: 15
+    description: |
+      Internal READ to PRECHARGE command delay in terms of number of clock
+      cycles.
+
+  tW2W-C2C-min-tck:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    enum: [0, 1]
+    description: |
+      Additional WRITE-to-WRITE delay in chip-to-chip cases in terms of number
+      of clock cycles.
+
+  tWL-min-tck:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    maximum: 15
+    description: |
+      WRITE data latency in terms of number of clock cycles.
+
+  tWR-min-tck:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    maximum: 15
+    description: |
+      WRITE recovery time in terms of number of clock cycles.
+
+  tWTR-min-tck:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    maximum: 15
+    description: |
+      Internal WRITE-to-READ command delay in terms of number of clock cycles.
+
+  tXP-min-tck:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    maximum: 255
+    description: |
+      Exit power-down to next valid command delay in terms of number of clock
+      cycles.
+
+  tXSR-min-tck:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    maximum: 1023
+    description: |
+      SELF REFRESH exit to next valid command delay in terms of number of clock
+      cycles.
+
+patternProperties:
+  "^timings((-[0-9])+|(@[0-9a-f]+))?$":
+    $ref: jedec,lpddr3-timings.yaml
+    description: |
+      The lpddr3 node may have one or more child nodes with timings.
+      Each timing node provides AC timing parameters of the device for a given
+      speed-bin. The user may provide the timings for as many speed-bins as is
+      required.
+
+required:
+  - compatible
+  - density
+  - io-width
+
+additionalProperties: false
+
+examples:
+  - |
+    lpddr3 {
+        compatible = "samsung,K3QF2F20DB", "jedec,lpddr3";
+        density = <16384>;
+        io-width = <32>;
+
+        tCKE-min-tck = <2>;
+        tCKESR-min-tck = <2>;
+        tDQSCK-min-tck = <5>;
+        tFAW-min-tck = <5>;
+        tMRD-min-tck = <5>;
+        tR2R-C2C-min-tck = <0>;
+        tRAS-min-tck = <5>;
+        tRC-min-tck = <6>;
+        tRCD-min-tck = <3>;
+        tRFC-min-tck = <17>;
+        tRL-min-tck = <14>;
+        tRPab-min-tck = <2>;
+        tRPpb-min-tck = <2>;
+        tRRD-min-tck = <2>;
+        tRTP-min-tck = <2>;
+        tW2W-C2C-min-tck = <0>;
+        tWL-min-tck = <8>;
+        tWR-min-tck = <7>;
+        tWTR-min-tck = <2>;
+        tXP-min-tck = <2>;
+        tXSR-min-tck = <12>;
+
+        timings {
+            compatible = "jedec,lpddr3-timings";
+            max-freq = <800000000>;
+            min-freq = <100000000>;
+            tCKE = <3750>;
+            tCKESR = <3750>;
+            tFAW = <25000>;
+            tMRD = <7000>;
+            tR2R-C2C = <0>;
+            tRAS = <23000>;
+            tRC = <33750>;
+            tRCD = <10000>;
+            tRFC = <65000>;
+            tRPab = <12000>;
+            tRPpb = <12000>;
+            tRRD = <6000>;
+            tRTP = <3750>;
+            tW2W-C2C = <0>;
+            tWR = <7500>;
+            tWTR = <3750>;
+            tXP = <3750>;
+            tXSR = <70000>;
+        };
+    };
diff --git a/Documentation/devicetree/bindings/memory-controllers/ddr/lpddr2-timings.txt b/Documentation/devicetree/bindings/memory-controllers/ddr/lpddr2-timings.txt
deleted file mode 100644
index 9ceb19e0c7fd..000000000000
--- a/Documentation/devicetree/bindings/memory-controllers/ddr/lpddr2-timings.txt
+++ /dev/null
@@ -1,52 +0,0 @@
-* AC timing parameters of LPDDR2(JESD209-2) memories for a given speed-bin
-
-Required properties:
-- compatible : Should be "jedec,lpddr2-timings"
-- min-freq : minimum DDR clock frequency for the speed-bin. Type is <u32>
-- max-freq : maximum DDR clock frequency for the speed-bin. Type is <u32>
-
-Optional properties:
-
-The following properties represent AC timing parameters from the memory
-data-sheet of the device for a given speed-bin. All these properties are
-of type <u32> and the default unit is ps (pico seconds). Parameters with
-a different unit have a suffix indicating the unit such as 'tRAS-max-ns'
-- tRCD
-- tWR
-- tRAS-min
-- tRRD
-- tWTR
-- tXP
-- tRTP
-- tDQSCK-max
-- tFAW
-- tZQCS
-- tZQinit
-- tRPab
-- tZQCL
-- tCKESR
-- tRAS-max-ns
-- tDQSCK-max-derated
-
-Example:
-
-timings_elpida_ECB240ABACN_400mhz: lpddr2-timings@0 {
-	compatible	= "jedec,lpddr2-timings";
-	min-freq	= <10000000>;
-	max-freq	= <400000000>;
-	tRPab		= <21000>;
-	tRCD		= <18000>;
-	tWR		= <15000>;
-	tRAS-min	= <42000>;
-	tRRD		= <10000>;
-	tWTR		= <7500>;
-	tXP		= <7500>;
-	tRTP		= <7500>;
-	tCKESR		= <15000>;
-	tDQSCK-max	= <5500>;
-	tFAW		= <50000>;
-	tZQCS		= <90000>;
-	tZQCL		= <360000>;
-	tZQinit		= <1000000>;
-	tRAS-max-ns	= <70000>;
-};
diff --git a/Documentation/devicetree/bindings/memory-controllers/ddr/lpddr3-timings.txt b/Documentation/devicetree/bindings/memory-controllers/ddr/lpddr3-timings.txt
deleted file mode 100644
index 84705e50a3fd..000000000000
--- a/Documentation/devicetree/bindings/memory-controllers/ddr/lpddr3-timings.txt
+++ /dev/null
@@ -1,58 +0,0 @@
-* AC timing parameters of LPDDR3 memories for a given speed-bin.
-
-The structures are based on LPDDR2 and extended where needed.
-
-Required properties:
-- compatible : Should be "jedec,lpddr3-timings"
-- min-freq : minimum DDR clock frequency for the speed-bin. Type is <u32>
-- reg : maximum DDR clock frequency for the speed-bin. Type is <u32>
-
-Optional properties:
-
-The following properties represent AC timing parameters from the memory
-data-sheet of the device for a given speed-bin. All these properties are
-of type <u32> and the default unit is ps (pico seconds).
-- tRFC
-- tRRD
-- tRPab
-- tRPpb
-- tRCD
-- tRC
-- tRAS
-- tWTR
-- tWR
-- tRTP
-- tW2W-C2C
-- tR2R-C2C
-- tFAW
-- tXSR
-- tXP
-- tCKE
-- tCKESR
-- tMRD
-
-Example:
-
-timings_samsung_K3QF2F20DB_800mhz: lpddr3-timings@800000000 {
-	compatible	= "jedec,lpddr3-timings";
-	reg		= <800000000>; /* workaround: it shows max-freq */
-	min-freq	= <100000000>;
-	tRFC		= <65000>;
-	tRRD		= <6000>;
-	tRPab		= <12000>;
-	tRPpb		= <12000>;
-	tRCD		= <10000>;
-	tRC		= <33750>;
-	tRAS		= <23000>;
-	tWTR		= <3750>;
-	tWR		= <7500>;
-	tRTP		= <3750>;
-	tW2W-C2C	= <0>;
-	tR2R-C2C	= <0>;
-	tFAW		= <25000>;
-	tXSR		= <70000>;
-	tXP		= <3750>;
-	tCKE		= <3750>;
-	tCKESR		= <3750>;
-	tMRD		= <7000>;
-};
diff --git a/Documentation/devicetree/bindings/memory-controllers/ddr/lpddr3.txt b/Documentation/devicetree/bindings/memory-controllers/ddr/lpddr3.txt
deleted file mode 100644
index 031af5fb0379..000000000000
--- a/Documentation/devicetree/bindings/memory-controllers/ddr/lpddr3.txt
+++ /dev/null
@@ -1,107 +0,0 @@
-* LPDDR3 SDRAM memories compliant to JEDEC JESD209-3C
-
-Required properties:
-- compatible : Should be "<vendor>,<type>", and generic value "jedec,lpddr3".
-  Example "<vendor>,<type>" values:
-    "samsung,K3QF2F20DB"
-
-- density  : <u32> representing density in Mb (Mega bits)
-- io-width : <u32> representing bus width. Possible values are 8, 16, 32, 64
-- #address-cells: Must be set to 1
-- #size-cells: Must be set to 0
-
-Optional properties:
-
-- manufacturer-id : <u32>     Manufacturer ID value read from Mode Register 5
-- revision-id     : <u32 u32> Revision IDs read from Mode Registers 6 and 7
-
-The following optional properties represent the minimum value of some AC
-timing parameters of the DDR device in terms of number of clock cycles.
-These values shall be obtained from the device data-sheet.
-- tRFC-min-tck
-- tRRD-min-tck
-- tRPab-min-tck
-- tRPpb-min-tck
-- tRCD-min-tck
-- tRC-min-tck
-- tRAS-min-tck
-- tWTR-min-tck
-- tWR-min-tck
-- tRTP-min-tck
-- tW2W-C2C-min-tck
-- tR2R-C2C-min-tck
-- tWL-min-tck
-- tDQSCK-min-tck
-- tRL-min-tck
-- tFAW-min-tck
-- tXSR-min-tck
-- tXP-min-tck
-- tCKE-min-tck
-- tCKESR-min-tck
-- tMRD-min-tck
-
-Child nodes:
-- The lpddr3 node may have one or more child nodes of type "lpddr3-timings".
-  "lpddr3-timings" provides AC timing parameters of the device for
-  a given speed-bin. Please see
-  Documentation/devicetree/bindings/memory-controllers/ddr/lpddr3-timings.txt
-  for more information on "lpddr3-timings"
-
-Example:
-
-samsung_K3QF2F20DB: lpddr3 {
-	compatible	= "samsung,K3QF2F20DB", "jedec,lpddr3";
-	density		= <16384>;
-	io-width	= <32>;
-	manufacturer-id = <1>;
-	revision-id     = <123 234>;
-	#address-cells	= <1>;
-	#size-cells	= <0>;
-
-	tRFC-min-tck		= <17>;
-	tRRD-min-tck		= <2>;
-	tRPab-min-tck		= <2>;
-	tRPpb-min-tck		= <2>;
-	tRCD-min-tck		= <3>;
-	tRC-min-tck		= <6>;
-	tRAS-min-tck		= <5>;
-	tWTR-min-tck		= <2>;
-	tWR-min-tck		= <7>;
-	tRTP-min-tck		= <2>;
-	tW2W-C2C-min-tck	= <0>;
-	tR2R-C2C-min-tck	= <0>;
-	tWL-min-tck		= <8>;
-	tDQSCK-min-tck		= <5>;
-	tRL-min-tck		= <14>;
-	tFAW-min-tck		= <5>;
-	tXSR-min-tck		= <12>;
-	tXP-min-tck		= <2>;
-	tCKE-min-tck		= <2>;
-	tCKESR-min-tck		= <2>;
-	tMRD-min-tck		= <5>;
-
-	timings_samsung_K3QF2F20DB_800mhz: lpddr3-timings@800000000 {
-		compatible	= "jedec,lpddr3-timings";
-		/* workaround: 'reg' shows max-freq */
-		reg		= <800000000>;
-		min-freq	= <100000000>;
-		tRFC		= <65000>;
-		tRRD		= <6000>;
-		tRPab		= <12000>;
-		tRPpb		= <12000>;
-		tRCD		= <10000>;
-		tRC		= <33750>;
-		tRAS		= <23000>;
-		tWTR		= <3750>;
-		tWR		= <7500>;
-		tRTP		= <3750>;
-		tW2W-C2C	= <0>;
-		tR2R-C2C	= <0>;
-		tFAW		= <25000>;
-		tXSR		= <70000>;
-		tXP		= <3750>;
-		tCKE		= <3750>;
-		tCKESR		= <3750>;
-		tMRD		= <7000>;
-	};
-}
diff --git a/Documentation/devicetree/bindings/memory-controllers/fsl/fsl,ifc.yaml b/Documentation/devicetree/bindings/memory-controllers/fsl/fsl,ifc.yaml
new file mode 100644
index 000000000000..3be1db30bf41
--- /dev/null
+++ b/Documentation/devicetree/bindings/memory-controllers/fsl/fsl,ifc.yaml
@@ -0,0 +1,113 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/memory-controllers/fsl/fsl,ifc.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: FSL/NXP Integrated Flash Controller
+
+maintainers:
+  - Li Yang <leoyang.li@nxp.com>
+
+description: |
+  NXP's integrated flash controller (IFC) is an advanced version of the
+  enhanced local bus controller which includes similar programming and signal
+  interfaces with an extended feature set. The IFC provides access to multiple
+  external memory types, such as NAND flash (SLC and MLC), NOR flash, EPROM,
+  SRAM and other memories where address and data are shared on a bus.
+
+properties:
+  $nodename:
+    pattern: "^memory-controller@[0-9a-f]+$"
+
+  compatible:
+    const: fsl,ifc
+
+  "#address-cells":
+    enum: [2, 3]
+    description: |
+      Should be either two or three.  The first cell is the chipselect
+      number, and the remaining cells are the offset into the chipselect.
+
+  "#size-cells":
+    enum: [1, 2]
+    description: |
+      Either one or two, depending on how large each chipselect can be.
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    minItems: 1
+    maxItems: 2
+    description: |
+      IFC may have one or two interrupts.  If two interrupt specifiers are
+      present, the first is the "common" interrupt (CM_EVTER_STAT), and the
+      second is the NAND interrupt (NAND_EVTER_STAT).  If there is only one,
+      that interrupt reports both types of event.
+
+  little-endian:
+    type: boolean
+    description: |
+      If this property is absent, the big-endian mode will be in use as default
+      for registers.
+
+  ranges:
+    description: |
+      Each range corresponds to a single chipselect, and covers the entire
+      access window as configured.
+
+patternProperties:
+  "^.*@[a-f0-9]+(,[a-f0-9]+)+$":
+    type: object
+    description: |
+      Child device nodes describe the devices connected to IFC such as NOR (e.g.
+      cfi-flash) and NAND (fsl,ifc-nand). There might be board specific devices
+      like FPGAs, CPLDs, etc.
+
+    required:
+      - compatible
+      - reg
+
+required:
+  - compatible
+  - reg
+  - interrupts
+
+additionalProperties: false
+
+examples:
+  - |
+    soc {
+        #address-cells = <2>;
+        #size-cells = <2>;
+
+        memory-controller@ffe1e000 {
+            compatible = "fsl,ifc";
+            #address-cells = <2>;
+            #size-cells = <1>;
+            reg = <0x0 0xffe1e000 0 0x2000>;
+            interrupts = <16 2 19 2>;
+            little-endian;
+
+            /* NOR, NAND Flashes and CPLD on board */
+            ranges = <0x0 0x0 0x0 0xee000000 0x02000000>,
+                     <0x1 0x0 0x0 0xffa00000 0x00010000>,
+                     <0x3 0x0 0x0 0xffb00000 0x00020000>;
+
+            flash@0,0 {
+                #address-cells = <1>;
+                #size-cells = <1>;
+                compatible = "cfi-flash";
+                reg = <0x0 0x0 0x2000000>;
+                bank-width = <2>;
+                device-width = <1>;
+
+                partition@0 {
+                    /* 32MB for user data */
+                    reg = <0x0 0x02000000>;
+                    label = "NOR Data";
+                };
+            };
+        };
+    };
diff --git a/Documentation/devicetree/bindings/memory-controllers/fsl/ifc.txt b/Documentation/devicetree/bindings/memory-controllers/fsl/ifc.txt
deleted file mode 100644
index 89427b018ba7..000000000000
--- a/Documentation/devicetree/bindings/memory-controllers/fsl/ifc.txt
+++ /dev/null
@@ -1,82 +0,0 @@
-Integrated Flash Controller
-
-Properties:
-- name : Should be ifc
-- compatible : should contain "fsl,ifc". The version of the integrated
-               flash controller can be found in the IFC_REV register at
-               offset zero.
-
-- #address-cells : Should be either two or three.  The first cell is the
-                   chipselect number, and the remaining cells are the
-                   offset into the chipselect.
-- #size-cells : Either one or two, depending on how large each chipselect
-                can be.
-- reg : Offset and length of the register set for the device
-- interrupts: IFC may have one or two interrupts.  If two interrupt
-              specifiers are present, the first is the "common"
-              interrupt (CM_EVTER_STAT), and the second is the NAND
-              interrupt (NAND_EVTER_STAT).  If there is only one,
-              that interrupt reports both types of event.
-
-- little-endian : If this property is absent, the big-endian mode will
-                  be in use as default for registers.
-
-- ranges : Each range corresponds to a single chipselect, and covers
-           the entire access window as configured.
-
-Child device nodes describe the devices connected to IFC such as NOR (e.g.
-cfi-flash) and NAND (fsl,ifc-nand). There might be board specific devices
-like FPGAs, CPLDs, etc.
-
-Example:
-
-	ifc@ffe1e000 {
-		compatible = "fsl,ifc", "simple-bus";
-		#address-cells = <2>;
-		#size-cells = <1>;
-		reg = <0x0 0xffe1e000 0 0x2000>;
-		interrupts = <16 2 19 2>;
-		little-endian;
-
-		/* NOR, NAND Flashes and CPLD on board */
-		ranges = <0x0 0x0 0x0 0xee000000 0x02000000
-			  0x1 0x0 0x0 0xffa00000 0x00010000
-			  0x3 0x0 0x0 0xffb00000 0x00020000>;
-
-		flash@0,0 {
-			#address-cells = <1>;
-			#size-cells = <1>;
-			compatible = "cfi-flash";
-			reg = <0x0 0x0 0x2000000>;
-			bank-width = <2>;
-			device-width = <1>;
-
-			partition@0 {
-				/* 32MB for user data */
-				reg = <0x0 0x02000000>;
-				label = "NOR Data";
-			};
-		};
-
-		flash@1,0 {
-			#address-cells = <1>;
-			#size-cells = <1>;
-			compatible = "fsl,ifc-nand";
-			reg = <0x1 0x0 0x10000>;
-
-			partition@0 {
-				/* This location must not be altered  */
-				/* 1MB for u-boot Bootloader Image */
-				reg = <0x0 0x00100000>;
-				label = "NAND U-Boot Image";
-				read-only;
-			};
-		};
-
-		cpld@3,0 {
-			#address-cells = <1>;
-			#size-cells = <1>;
-			compatible = "fsl,p1010rdb-cpld";
-			reg = <0x3 0x0 0x000001f>;
-		};
-	};
diff --git a/Documentation/devicetree/bindings/memory-controllers/mediatek,smi-common.yaml b/Documentation/devicetree/bindings/memory-controllers/mediatek,smi-common.yaml
index 3a82b0b27fa0..a98b359bf909 100644
--- a/Documentation/devicetree/bindings/memory-controllers/mediatek,smi-common.yaml
+++ b/Documentation/devicetree/bindings/memory-controllers/mediatek,smi-common.yaml
@@ -16,7 +16,7 @@ description: |
   MediaTek SMI have two generations of HW architecture, here is the list
   which generation the SoCs use:
   generation 1: mt2701 and mt7623.
-  generation 2: mt2712, mt6779, mt8167, mt8173, mt8183, mt8192 and mt8195.
+  generation 2: mt2712, mt6779, mt8167, mt8173, mt8183, mt8186, mt8192 and mt8195.
 
   There's slight differences between the two SMI, for generation 2, the
   register which control the iommu port is at each larb's register base. But
@@ -35,6 +35,7 @@ properties:
           - mediatek,mt8167-smi-common
           - mediatek,mt8173-smi-common
           - mediatek,mt8183-smi-common
+          - mediatek,mt8186-smi-common
           - mediatek,mt8192-smi-common
           - mediatek,mt8195-smi-common-vdo
           - mediatek,mt8195-smi-common-vpp
@@ -88,10 +89,9 @@ allOf:
               - mediatek,mt2701-smi-common
     then:
       properties:
-        clock:
-          items:
-            minItems: 3
-            maxItems: 3
+        clocks:
+          minItems: 3
+          maxItems: 3
         clock-names:
           items:
             - const: apb
@@ -108,10 +108,9 @@ allOf:
       required:
         - mediatek,smi
       properties:
-        clock:
-          items:
-            minItems: 3
-            maxItems: 3
+        clocks:
+          minItems: 3
+          maxItems: 3
         clock-names:
           items:
             - const: apb
@@ -127,16 +126,16 @@ allOf:
           enum:
             - mediatek,mt6779-smi-common
             - mediatek,mt8183-smi-common
+            - mediatek,mt8186-smi-common
             - mediatek,mt8192-smi-common
             - mediatek,mt8195-smi-common-vdo
             - mediatek,mt8195-smi-common-vpp
 
     then:
       properties:
-        clock:
-          items:
-            minItems: 4
-            maxItems: 4
+        clocks:
+          minItems: 4
+          maxItems: 4
         clock-names:
           items:
             - const: apb
@@ -146,10 +145,9 @@ allOf:
 
     else:  # for gen2 HW that don't have gals
       properties:
-        clock:
-          items:
-            minItems: 2
-            maxItems: 2
+        clocks:
+          minItems: 2
+          maxItems: 2
         clock-names:
           items:
             - const: apb
diff --git a/Documentation/devicetree/bindings/memory-controllers/mediatek,smi-larb.yaml b/Documentation/devicetree/bindings/memory-controllers/mediatek,smi-larb.yaml
index eaeff1ada7f8..4db8690829cd 100644
--- a/Documentation/devicetree/bindings/memory-controllers/mediatek,smi-larb.yaml
+++ b/Documentation/devicetree/bindings/memory-controllers/mediatek,smi-larb.yaml
@@ -23,6 +23,7 @@ properties:
           - mediatek,mt8167-smi-larb
           - mediatek,mt8173-smi-larb
           - mediatek,mt8183-smi-larb
+          - mediatek,mt8186-smi-larb
           - mediatek,mt8192-smi-larb
           - mediatek,mt8195-smi-larb
 
@@ -75,15 +76,16 @@ allOf:
         compatible:
           enum:
             - mediatek,mt8183-smi-larb
+            - mediatek,mt8186-smi-larb
             - mediatek,mt8195-smi-larb
 
     then:
       properties:
-        clock:
-          items:
-            minItems: 3
-            maxItems: 3
+        clocks:
+          minItems: 2
+          maxItems: 3
         clock-names:
+          minItems: 2
           items:
             - const: apb
             - const: smi
@@ -91,10 +93,9 @@ allOf:
 
     else:
       properties:
-        clock:
-          items:
-            minItems: 2
-            maxItems: 2
+        clocks:
+          minItems: 2
+          maxItems: 2
         clock-names:
           items:
             - const: apb
@@ -108,7 +109,7 @@ allOf:
               - mediatek,mt2701-smi-larb
               - mediatek,mt2712-smi-larb
               - mediatek,mt6779-smi-larb
-              - mediatek,mt8167-smi-larb
+              - mediatek,mt8186-smi-larb
               - mediatek,mt8192-smi-larb
               - mediatek,mt8195-smi-larb
 
diff --git a/Documentation/devicetree/bindings/memory-controllers/renesas,rpc-if.yaml b/Documentation/devicetree/bindings/memory-controllers/renesas,rpc-if.yaml
index 294f1036420d..9a6dbf54b540 100644
--- a/Documentation/devicetree/bindings/memory-controllers/renesas,rpc-if.yaml
+++ b/Documentation/devicetree/bindings/memory-controllers/renesas,rpc-if.yaml
@@ -40,7 +40,8 @@ properties:
       - items:
           - enum:
               - renesas,r9a07g044-rpc-if      # RZ/G2{L,LC}
-          - const: renesas,rzg2l-rpc-if       # RZ/G2L family
+              - renesas,r9a07g054-rpc-if      # RZ/V2L
+          - const: renesas,rzg2l-rpc-if
 
   reg:
     items:
diff --git a/Documentation/devicetree/bindings/memory-controllers/samsung,exynos5422-dmc.yaml b/Documentation/devicetree/bindings/memory-controllers/samsung,exynos5422-dmc.yaml
index fe8639dcffab..044127788695 100644
--- a/Documentation/devicetree/bindings/memory-controllers/samsung,exynos5422-dmc.yaml
+++ b/Documentation/devicetree/bindings/memory-controllers/samsung,exynos5422-dmc.yaml
@@ -51,8 +51,7 @@ properties:
     $ref: '/schemas/types.yaml#/definitions/phandle'
     description: |
       phandle of the connected DRAM memory device. For more information please
-      refer to documentation file:
-      Documentation/devicetree/bindings/memory-controllers/ddr/lpddr3.txt
+      refer to jedec,lpddr3.yaml.
 
   operating-points-v2: true
 
diff --git a/Documentation/devicetree/bindings/power/amlogic,meson-sec-pwrc.yaml b/Documentation/devicetree/bindings/power/amlogic,meson-sec-pwrc.yaml
index 5dae04d2936c..7657721a4e96 100644
--- a/Documentation/devicetree/bindings/power/amlogic,meson-sec-pwrc.yaml
+++ b/Documentation/devicetree/bindings/power/amlogic,meson-sec-pwrc.yaml
@@ -12,13 +12,14 @@ maintainers:
   - Jianxin Pan <jianxin.pan@amlogic.com>
 
 description: |+
-  Secure Power Domains used in Meson A1/C1 SoCs, and should be the child node
+  Secure Power Domains used in Meson A1/C1/S4 SoCs, and should be the child node
   of secure-monitor.
 
 properties:
   compatible:
     enum:
       - amlogic,meson-a1-pwrc
+      - amlogic,meson-s4-pwrc
 
   "#power-domain-cells":
     const: 1
diff --git a/Documentation/devicetree/bindings/power/mediatek,power-controller.yaml b/Documentation/devicetree/bindings/power/mediatek,power-controller.yaml
index f234a756c193..135c6f722091 100644
--- a/Documentation/devicetree/bindings/power/mediatek,power-controller.yaml
+++ b/Documentation/devicetree/bindings/power/mediatek,power-controller.yaml
@@ -26,7 +26,9 @@ properties:
       - mediatek,mt8167-power-controller
       - mediatek,mt8173-power-controller
       - mediatek,mt8183-power-controller
+      - mediatek,mt8186-power-controller
       - mediatek,mt8192-power-controller
+      - mediatek,mt8195-power-controller
 
   '#power-domain-cells':
     const: 1
@@ -64,6 +66,7 @@ patternProperties:
               "include/dt-bindings/power/mt8173-power.h" - for MT8173 type power domain.
               "include/dt-bindings/power/mt8183-power.h" - for MT8183 type power domain.
               "include/dt-bindings/power/mt8192-power.h" - for MT8192 type power domain.
+              "include/dt-bindings/power/mt8195-power.h" - for MT8195 type power domain.
         maxItems: 1
 
       clocks:
diff --git a/Documentation/devicetree/bindings/power/qcom,rpmpd.yaml b/Documentation/devicetree/bindings/power/qcom,rpmpd.yaml
index f48bc41d81ec..940e97b565bf 100644
--- a/Documentation/devicetree/bindings/power/qcom,rpmpd.yaml
+++ b/Documentation/devicetree/bindings/power/qcom,rpmpd.yaml
@@ -17,6 +17,7 @@ properties:
   compatible:
     enum:
       - qcom,mdm9607-rpmpd
+      - qcom,msm8226-rpmpd
       - qcom,msm8916-rpmpd
       - qcom,msm8939-rpmpd
       - qcom,msm8953-rpmpd
diff --git a/Documentation/devicetree/bindings/remoteproc/qcom,adsp.yaml b/Documentation/devicetree/bindings/remoteproc/qcom,adsp.yaml
index c635c181d2c2..64c182428e94 100644
--- a/Documentation/devicetree/bindings/remoteproc/qcom,adsp.yaml
+++ b/Documentation/devicetree/bindings/remoteproc/qcom,adsp.yaml
@@ -47,6 +47,10 @@ properties:
       - qcom,sm8350-cdsp-pas
       - qcom,sm8350-slpi-pas
       - qcom,sm8350-mpss-pas
+      - qcom,sm8450-adsp-pas
+      - qcom,sm8450-cdsp-pas
+      - qcom,sm8450-mpss-pas
+      - qcom,sm8450-slpi-pas
 
   reg:
     maxItems: 1
@@ -175,6 +179,10 @@ allOf:
               - qcom,sm8350-cdsp-pas
               - qcom,sm8350-slpi-pas
               - qcom,sm8350-mpss-pas
+              - qcom,sm8450-adsp-pas
+              - qcom,sm8450-cdsp-pas
+              - qcom,sm8450-slpi-pas
+              - qcom,sm8450-mpss-pas
     then:
       properties:
         clocks:
@@ -283,6 +291,9 @@ allOf:
               - qcom,sm8350-adsp-pas
               - qcom,sm8350-cdsp-pas
               - qcom,sm8350-slpi-pas
+              - qcom,sm8450-adsp-pas
+              - qcom,sm8450-cdsp-pas
+              - qcom,sm8450-slpi-pas
     then:
       properties:
         interrupts:
@@ -312,6 +323,7 @@ allOf:
               - qcom,sm6350-mpss-pas
               - qcom,sm8150-mpss-pas
               - qcom,sm8350-mpss-pas
+              - qcom,sm8450-mpss-pas
     then:
       properties:
         interrupts:
@@ -434,6 +446,7 @@ allOf:
               - qcom,sm6350-mpss-pas
               - qcom,sm8150-mpss-pas
               - qcom,sm8350-mpss-pas
+              - qcom,sm8450-mpss-pas
     then:
       properties:
         power-domains:
@@ -458,6 +471,8 @@ allOf:
               - qcom,sm8250-slpi-pas
               - qcom,sm8350-adsp-pas
               - qcom,sm8350-slpi-pas
+              - qcom,sm8450-adsp-pas
+              - qcom,sm8450-slpi-pas
     then:
       properties:
         power-domains:
@@ -475,6 +490,7 @@ allOf:
           contains:
             enum:
               - qcom,sm8350-cdsp-pas
+              - qcom,sm8450-cdsp-pas
     then:
       properties:
         power-domains:
diff --git a/Documentation/devicetree/bindings/soc/mediatek/pwrap.txt b/Documentation/devicetree/bindings/soc/mediatek/pwrap.txt
index d74a7a5ae9f2..214a34633824 100644
--- a/Documentation/devicetree/bindings/soc/mediatek/pwrap.txt
+++ b/Documentation/devicetree/bindings/soc/mediatek/pwrap.txt
@@ -27,6 +27,7 @@ Required properties in pwrap device node.
 	"mediatek,mt8135-pwrap" for MT8135 SoCs
 	"mediatek,mt8173-pwrap" for MT8173 SoCs
 	"mediatek,mt8183-pwrap" for MT8183 SoCs
+	"mediatek,mt8186-pwrap" for MT8186 SoCs
 	"mediatek,mt8195-pwrap" for MT8195 SoCs
 	"mediatek,mt8516-pwrap" for MT8516 SoCs
 - interrupts: IRQ for pwrap in SOC