| Age | Commit message (Collapse) | Author |
|---|
|
In DMA threshold mode, frame underflow errors may sometimes occur when
the TC(threshold control) value is not enough. The TC value need to be
bumped up in this case.
There is no underflow interrupt bit on DMA_CH(#i)_Status of dwmac4, so
the DMA threshold cannot be bumped up in stmmac_dma_interrupt(). The
i.mx8mp board observed an underflow error while running NFS boot, the
NFS rootfs could not be mounted.
The underflow error can be got from the DMA descriptor TDES3 on dwmac4.
This patch bump up tc value once underflow error is got from TDES3.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This big patch sprinkles const on local variables and
function arguments which may refer to netdev->dev_addr.
Commit 406f42fa0d3c ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
Some of the changes here are not strictly required - const
is sometimes cast off but pointer is not used for writing.
It seems like it's still better to add the const in case
the code changes later or relevant -W flags get enabled
for the build.
No functional changes.
Link: https://lore.kernel.org/r/20211014142432.449314-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Adding ethtool per-queue statistics support to show number of interrupts
generated at DMA tx and DMA rx. All the counters are incremented at
dwmac4_dma_interrupt function.
Signed-off-by: Vijayakannan Ayyathurai <vijayakannan.ayyathurai@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adding generic ethtool per-queue statistic framework to display the
statistics for each rx/tx queue. In future, users can avail it to add
more per-queue specific counters. Number of rx/tx queues displayed is
depending on the available rx/tx queues in that particular MAC config
and this number is limited up to the MTL_MAX_{RX|TX}_QUEUES defined
in the driver.
Ethtool per-queue statistic display will look like below, when users
start adding more counters.
Example:
q0_tx_statA:
q0_tx_statB:
q0_tx_statC:
|
q0_tx_statX:
.
.
.
qMAX_tx_statA:
qMAX_tx_statB:
qMAX_tx_statC:
|
qMAX_tx_statX:
q0_rx_statA:
q0_rx_statB:
q0_rx_statC:
|
q0_rx_statX:
.
.
.
qMAX_rx_statA:
qMAX_rx_statB:
qMAX_rx_statC:
|
qMAX_rx_statX:
In addition, this patch has the support on displaying the number of
packets received and transmitted per queue.
Signed-off-by: Vijayakannan Ayyathurai <vijayakannan.ayyathurai@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The struct mdio_xpcs_args is reminiscent of when a similarly named
struct mdio_xpcs_ops existed. Now that that is removed, we can shorten
the name to dw_xpcs (dw for DesignWare).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since all the remaining members of struct mdio_xpcs_ops have direct
equivalents in struct phylink_pcs_ops, it is about time we remove it
altogether.
Since the phylink ops return void, we need to remove the error
propagation from the various xpcs methods and simply print an error
message where appropriate.
Since xpcs_get_state_c73() detects link faults and attempts to reset the
link on its own by calling xpcs_config(), but xpcs_config() now has a
lot of phylink arguments which are not needed and cannot be simply
fabricated by anybody else except phylink, the actual implementation has
been moved into a smaller xpcs_do_config().
The const struct mdio_xpcs_ops *priv->hw->xpcs has been removed, so we
need to look at the struct mdio_xpcs_args pointer now as an indication
whether the port has an XPCS or not.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Unify the 2 existing PCS drivers (lynx and xpcs) by doing a similar
thing on probe, which is to have a *_create function that takes a
struct mdio_device * given by the caller, and builds a private PCS
structure around that.
This changes stmmac to hold only a pointer to the xpcs, as opposed to
the full structure. This will be used in the next patch when struct
mdio_xpcs_ops is removed. Currently a pointer to struct mdio_xpcs_ops
is used as a shorthand to determine whether the port has an XPCS or not.
We can do the same now with the mdio_xpcs_args pointer.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
DWMAC Core 5.20 onwards supports HW descriptor prefetching.
Additionally, it also depends on platform specific RTL configuration.
This capability could be enabled by setting DMA_Mode bit-19 (DCHE).
So, to enable this cability, platform must set plat->dma_cfg->dche = true
and the DWMAC core version must be 5.20 onwards. Else, this capability
wouldn`t be configured
Signed-off-by: Mohammad Athari Bin Ismail <mohammad.athari.ismail@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now we introduce MSI interrupt service routines and hook these routines
up if stmmac_open() sees valid irq line being requested:-
stmmac_mac_interrupt() :- MAC (dev->irq), WOL (wol_irq), LPI (lpi_irq)
stmmac_safety_interrupt() :- Safety Feat Correctible Error (sfty_ce_irq)
& Uncorrectible Error (sfty_ue_irq)
stmmac_msi_intr_rx() :- For all RX MSI irq (rx_irq)
stmmac_msi_intr_tx() :- For all TX MSI irq (tx_irq)
Each of IRQs will have its unique name so that we can differentiate
them easily under /proc/interrupts.
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: Voon Weifeng <weifeng.voon@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In preparation to make stmmac support multi-vector MSI, we introduce the
interrupt status masking according to RX, TX or RXTX. Default to use RXTX
inside stmmac_dma_interrupt(), so there is no run-time logic difference
now.
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: Voon Weifeng <weifeng.voon@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In order to discover whether remote station supports frame preemption,
local station sends verify mPacket and expects response mPacket in
return from the remote station.
So, we add the functions to send and handle event when verify mPacket
and response mPacket are exchanged between the networked stations.
The mechanism to handle different FPE states between local and remote
station (link partner) is implemented using workqueue which starts a
task each time there is some sign of verify & response mPacket exchange
as check in FPE IRQ event. The task retries couple of times to try to
spot the states that both stations are ready to enter FPE ON. This allows
different end points to enable FPE at different time and verify-response
mPacket can happen asynchronously. Ultimately, the task will only turn
FPE ON when local station have both exchange response in both directions.
Thanks to Voon Weifeng for implementing the core functions for detecting
FPE events and send mPacket and phylink related change.
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Co-developed-by: Voon Weifeng <weifeng.voon@intel.com>
Signed-off-by: Voon Weifeng <weifeng.voon@intel.com>
Co-developed-by: Tan Tee Min <tee.min.tan@intel.com>
Signed-off-by: Tan Tee Min <tee.min.tan@intel.com>
Co-developed-by: Mohammad Athari Bin Ismail <mohammad.athari.ismail@intel.com>
Signed-off-by: Mohammad Athari Bin Ismail <mohammad.athari.ismail@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Cross timestamping is supported on Integrated Ethernet Controller in
Intel SoC such as EHL and TGL with Always Running Timer.
The hardware cross-timestamp result is made available to
applications through the PTP_SYS_OFFSET_PRECISE ioctl which calls
stmmac_getcrosststamp().
Device time is stored in the MAC Auxiliary register. The 64-bit System
time (ART timestamp) is stored in registers that are only addressable
by using MDIO space.
Signed-off-by: Tan Tee Min <tee.min.tan@intel.com>
Co-developed-by: Wong Vee Khee <vee.khee.wong@linux.intel.com>
Signed-off-by: Wong Vee Khee <vee.khee.wong@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Below EST errors are added into ethtool statistic:
1) Constant Gate Control Error (CGCE):
The counter "mtl_est_cgce" increases everytime CGCE interrupt is
triggered.
2) Head-of-Line Blocking due to Scheduling (HLBS):
The counter "mtl_est_hlbs" increases everytime HLBS interrupt is
triggered.
3) Head-of-Line Blocking due to Frame Size (HLBF):
The counter "mtl_est_hlbf" increases everytime HLBF interrupt is
triggered.
4) Base Time Register error (BTRE):
The counter "mtl_est_btre" increases everytime BTRE interrupt is
triggered but BTRL not reaches maximum value of 15.
5) Base Time Register Error Loop Count (BTRL) reaches maximum value:
The counter "mtl_est_btrlm" increases everytime BTRE interrupt is
triggered and BTRL value reaches maximum value of 15.
Please refer to MTL_EST_STATUS register in DesignWare Cores Ethernet
Quality-of-Service Databook for more detail explanation.
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: Voon Weifeng <weifeng.voon@intel.com>
Co-developed-by: Mohammad Athari Bin Ismail <mohammad.athari.ismail@intel.com>
Signed-off-by: Mohammad Athari Bin Ismail <mohammad.athari.ismail@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch enables the HW LPI Timer which controls the automatic entry
and exit of the LPI state.
The EEE LPI timer value is configured through ethtool. The driver will
auto select the LPI HW timer if the value in the HW timer supported range.
Else, the driver will fallback to SW timer.
Signed-off-by: Vineetha G. Jaya Kumaran <vineetha.g.jaya.kumaran@intel.com>
Signed-off-by: Voon Weifeng <weifeng.voon@intel.com>
Link: https://lore.kernel.org/r/20201027160051.22898-1-weifeng.voon@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add option in plat_stmmacenet_data struct to enable VLAN Filter Fail
Queuing. This option allows packets that fail VLAN filter to be routed
to a specific Rx queue when Receive All is also set.
When this option is enabled:
- Enable VFFQ only when entering promiscuous mode, because Receive All
will pass up all rx packets that failed address filtering (similar to
promiscuous mode).
- VLAN-promiscuous mode is never entered to allow rx packet to fail VLAN
filters and get routed to selected VFFQ Rx queue.
Reviewed-by: Voon Weifeng <weifeng.voon@intel.com>
Reviewed-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: Chuah, Kim Tatt <kim.tatt.chuah@intel.com>
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch add support to --show-ring & --set-ring Ethtool functions:
- Adding min, max, power of two check to new ring parameter's value.
- Bring down the network interface before changing the value of ring
parameters.
- Bring up the network interface after changing the value of ring
parameters.
Signed-off-by: Song, Yoong Siang <yoong.siang.song@intel.com>
Signed-off-by: Voon Weifeng <weifeng.voon@intel.com>
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Create drivers/net/pcs and move the Synopsys DesignWare XPCS into the
new directory. Move the header file into a subdirectory
include/linux/pcs
Start a naming convention of all PCS files use the prefix pcs-, and
rename the XPCS files to fit.
v2:
Add include/linux/pcs
v4:
Fix include path in stmmac.
Remove PCS_DEVICES to avoid new prompts
Cc: Jose Abreu <Jose.Abreu@synopsys.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For dwmac4, enable VLAN promiscuity when MAC controller is requested to
enter promiscuous mode.
Signed-off-by: Chuah, Kim Tatt <kim.tatt.chuah@intel.com>
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: Tan, Tee Min <tee.min.tan@intel.com>
Signed-off-by: Wong Vee Khee <vee.khee.wong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for VLAN ID-based filtering by the MAC controller for MAC
drivers that support it. Only the 12-bit VID field is used.
Signed-off-by: Chuah Kim Tatt <kim.tatt.chuah@intel.com>
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: Wong Vee Khee <vee.khee.wong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adds the support for Enterprise MAC IP version which is very similar to
XGMAC. It's so similar that we just need to check the device id and add
new speeds definitions and some minor callbacks.
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add XLGMII support for stmmac including the list of speeds and defines
for them.
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adds all the necessary logic so that stmmac can be used with Synopsys
DesignWare XPCS.
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adds the support for ETF scheduler using TBS feature which is available
in XGMAC and QoS IPs.
Changes from v2:
- Fix checkpatch issues (Jakub)
- Use the TBS bitfield
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Mere overlapping changes in the conflicts here.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adds the support for Frame Preemption using TAPRIO API. This works along
with EST feature and allows to select if preemptable traffic shall be
sent during specific queues opening time.
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adds the support for EST in GMAC5+ cores. This feature allows to offload
scheduling of queues opening time to the IP.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The 16KB RX Buffer must also be 16 byte aligned. Fix it.
Fixes: 7ac6653a085b ("stmmac: Move the STMicroelectronics driver")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Tune-up the defalt coalesce settings for optimal values. This gives the
best performance in most of the use-cases.
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For performance reasons, sometimes using the minimum RX Coalesce value
is not optimal. Lets setup a default value that is optimal in most of
the use cases.
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Implement the ARP Offload feature in XGMAC cores.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Implement filters for Layer 3 and Layer 4 using TC Flower API. Add the
corresponding callbacks in XGMAC core.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adds the logic to insert a given VLAN ID in a packet. This is offloaded
to HW and its descriptor based. For now, only XGMAC implements the
necessary callbacks.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a counter that increments each time a packet with split header is
received.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add the support for Split Header feature in the RX path and enable it in
XGMAC cores.
This does not impact neither beneficts bandwidth but it does reduces CPU
usage because without the feature all the entire packet is memcpy'ed,
while that with the feature only the header is.
With Split Header disabled 'perf stat -d' gives:
86870.624945 task-clock (msec) # 0.429 CPUs utilized
1073352 context-switches # 0.012 M/sec
1 cpu-migrations # 0.000 K/sec
213 page-faults # 0.002 K/sec
327113872376 cycles # 3.766 GHz (62.53%)
56618161216 instructions # 0.17 insn per cycle (75.06%)
10742205071 branches # 123.658 M/sec (75.36%)
584309242 branch-misses # 5.44% of all branches (75.19%)
17594787965 L1-dcache-loads # 202.540 M/sec (74.88%)
4003773131 L1-dcache-load-misses # 22.76% of all L1-dcache hits (74.89%)
1313301468 LLC-loads # 15.118 M/sec (49.75%)
355906510 LLC-load-misses # 27.10% of all LL-cache hits (49.92%)
With Split Header enabled 'perf stat -d' gives:
49324.456539 task-clock (msec) # 0.245 CPUs utilized
2542387 context-switches # 0.052 M/sec
1 cpu-migrations # 0.000 K/sec
213 page-faults # 0.004 K/sec
177092791469 cycles # 3.590 GHz (62.30%)
68555756017 instructions # 0.39 insn per cycle (75.16%)
12697019382 branches # 257.418 M/sec (74.81%)
442081897 branch-misses # 3.48% of all branches (74.79%)
20337958358 L1-dcache-loads # 412.330 M/sec (75.46%)
3820210140 L1-dcache-load-misses # 18.78% of all L1-dcache hits (75.35%)
1257719198 LLC-loads # 25.499 M/sec (49.73%)
685543923 LLC-load-misses # 54.51% of all LL-cache hits (49.86%)
Changes from v2:
- Reword commit message (Jakub)
Changes from v1:
- Add performance info (David)
- Add misssing dma_sync_single_for_device()
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Implement the VLAN Hash Filtering feature in XGMAC core.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Implement the RSS functionality and add the corresponding callbacks in
XGMAC core.
Changes from v1:
- Do not use magic constants (Jakub)
- Use ethtool_rxfh_indir_default() (Jakub)
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
1. get hash table size in hw feature reigster, and add support
for taller hash table(128/256) in dwmac4.
2. only clear GMAC_PACKET_FILTER bits used in this function,
to avoid side effect to functions of other bits.
stmmac selftests output log with flow control on:
ethtool -t eth0
The test result is PASS
The test extra info:
1. MAC Loopback 0
2. PHY Loopback -95
3. MMC Counters 0
4. EEE -95
5. Hash Filter MC 0
6. Perfect Filter UC 0
7. MC Filter 0
8. UC Filter 0
9. Flow Control 0
Signed-off-by: Biao Huang <biao.huang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for coalescing RX path by specifying number of frames which
don't need to have interrupt on completion bit set.
This is only available when RX Watchdog is enabled.
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, stmmac only supports 32 bits addressing for SKB. Enable the
support for upto 48 bits addressing in XGMAC core.
This avoids the use of bounce buffers and increases performance.
Changes from v1:
- Fallback to 32 bits in failure (Andrew)
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
XGMAC supports following speeds:
- 10G XGMII
- 5G XGMII
- 2.5G XGMII
- 2.5G GMII
- 1G GMII
- 100M MII
- 10M MII
Add them to the stmmac driver.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For performance reasons decrease the default RX Watchdog value for the
minimum allowed.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Honestly all the conflicts were simple overlapping changes,
nothing really interesting to report.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
the default value of tx-frames is 25, it's too late when
passing tstamp to stack, then the ptp4l will fail:
ptp4l -i eth0 -f gPTP.cfg -m
ptp4l: selected /dev/ptp0 as PTP clock
ptp4l: port 1: INITIALIZING to LISTENING on INITIALIZE
ptp4l: port 0: INITIALIZING to LISTENING on INITIALIZE
ptp4l: port 1: link up
ptp4l: timed out while polling for tx timestamp
ptp4l: increasing tx_timestamp_timeout may correct this issue,
but it is likely caused by a driver bug
ptp4l: port 1: send peer delay response failed
ptp4l: port 1: LISTENING to FAULTY on FAULT_DETECTED (FT_UNSPECIFIED)
ptp4l tests pass when changing the tx-frames from 25 to 1 with
ethtool -C option.
It should be fine to set tx-frames default value to 1, so ptp4l will pass
by default.
Signed-off-by: Biao Huang <biao.huang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms and conditions of the gnu general public license
version 2 as published by the free software foundation this program
is distributed in the hope it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details the full gnu general public license is included in
this distribution in the file called copying
this program is free software you can redistribute it and or modify
it under the terms and conditions of the gnu general public license
version 2 as published by the free software foundation this program
is distributed in the hope [that] it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details the full gnu general public license is included in
this distribution in the file called copying
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 57 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141901.515993066@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
XGMAC has a different MMC module. Lets use HWIF callbacks for MMC module
so that correct callbacks are automatically selected.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Ping problems with packets > 8191 as shown:
PING 192.168.1.99 (192.168.1.99) 8150(8178) bytes of data.
8158 bytes from 192.168.1.99: icmp_seq=1 ttl=64 time=0.669 ms
wrong data byte 8144 should be 0xd0 but was 0x0
16 10 11 12 13 14 15 16 17 18 19 1a 1b 1c 1d 1e 1f
20 21 22 23 24 25 26 27 28 29 2a 2b 2c 2d 2e 2f
%< ---------------snip--------------------------------------
8112 b0 b1 b2 b3 b4 b5 b6 b7 b8 b9 ba bb bc bd be bf
c0 c1 c2 c3 c4 c5 c6 c7 c8 c9 ca cb cc cd ce cf
8144 0 0 0 0 d0 d1
^^^^^^^
Notice the 4 bytes of 0 before the expected byte of d0.
Databook notes that the RX buffer must be a multiple of 4/8/16
bytes [1].
Update the DMA Buffer size define to 8188 instead of 8192. Remove
the -1 from the RX buffer size allocations and use the new
DMA Buffer size directly.
[1] Synopsys DesignWare Cores Ethernet MAC Universal v3.70a
[section 8.4.2 - Table 8-24]
Tested on SoCFPGA Stratix10 with ping sweep from 100 to 8300 byte packets.
Fixes: 286a83721720 ("stmmac: add CHAINED descriptor mode support (V4)")
Suggested-by: Jose Abreu <jose.abreu@synopsys.com>
Signed-off-by: Thor Thayer <thor.thayer@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This follows David Miller advice and tries to fix coalesce timer in
multi-queue scenarios.
We are now using per-queue coalesce values and per-queue TX timer.
Coalesce timer default values was changed to 1ms and the coalesce frames
to 25.
Tested in B2B setup between XGMAC2 and GMAC5.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Fixes: ce736788e8a ("net: stmmac: adding multiple buffers for TX")
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Jerome Brunet <jbrunet@baylibre.com>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add the MAC related callbacks for the new IP block XGMAC2.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a new entry to HWIF table for XGMAC 2.10. For now we fill it with
empty callbacks which will be added in posterior patches.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This adds support for Flexible PPS output (which is equivalent
to per_out output of PTP subsystem).
Tested using an oscilloscope and the following commands:
1) Start PTP4L:
# ptp4l -A -4 -H -m -i eth0 &
2) Set Flexible PPS frequency:
# echo <idx> <ts> <tns> <ps> <pns> > /sys/class/ptp/ptpX/period
Where, ts/tns is start time and ps/pns is period time, and ptpX is ptp
of eth0.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Vitor Soares <soares@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
