path: root/doc/ietf/draft-valin-celt-rtp-profile-01.txt

AVT Working Group                                             J-M. Valin
Internet-Draft                                     Octasic Semiconductor
Expires: November 12, 2009                                    G. Maxwell
                                                        Juniper Networks
                                                            May 11, 2009


                    draft-valin-celt-rtp-profile-01
                 RTP Payload Format for the CELT Codec

Status of this Memo

   This Internet-Draft is submitted to IETF in full conformance with the
   provisions of BCP 78 and BCP 79.

   Internet-Drafts are working documents of the Internet Engineering
   Task Force (IETF), its areas, and its working groups.  Note that
   other groups may also distribute working documents as Internet-
   Drafts.

   Internet-Drafts are draft documents valid for a maximum of six months
   and may be updated, replaced, or obsoleted by other documents at any
   time.  It is inappropriate to use Internet-Drafts as reference
   material or to cite them other than as "work in progress."

   The list of current Internet-Drafts can be accessed at
   http://www.ietf.org/ietf/1id-abstracts.txt.

   The list of Internet-Draft Shadow Directories can be accessed at
   http://www.ietf.org/shadow.html.

   This Internet-Draft will expire on November 12, 2009.

Copyright Notice

   Copyright (c) 2009 IETF Trust and the persons identified as the
   document authors.  All rights reserved.

   This document is subject to BCP 78 and the IETF Trust's Legal
   Provisions Relating to IETF Documents in effect on the date of
   publication of this document (http://trustee.ietf.org/license-info).
   Please review these documents carefully, as they describe your rights
   and restrictions with respect to this document.








Valin & Maxwell         Expires November 12, 2009               [Page 1]

Internet-Draft       draft-valin-celt-rtp-profile-01            May 2009


Abstract

   CELT is an open-source voice codec suitable for use in very low delay
   audio communication applications, including Voice over IP (VoIP).
   This document describes the payload format for CELT generated bit
   streams within an RTP packet.  Also included here are the necessary
   details for the use of CELT with the Session Description Protocol
   (SDP).  At the time of this writing, the CELT bit-stream has NOT been
   finalized yet, and compatibility is usually broken with every new
   release of the codec.


Table of Contents

   1.  Conventions used in this document  . . . . . . . . . . . . . .  3
   2.  Overview of the CELT Codec . . . . . . . . . . . . . . . . . .  4
   3.  RTP payload format for CELT  . . . . . . . . . . . . . . . . .  5
     3.1.  RTP Header . . . . . . . . . . . . . . . . . . . . . . . .  5
     3.2.  CELT payload . . . . . . . . . . . . . . . . . . . . . . .  6
     3.3.  Multiple CELT frames in a RTP packet . . . . . . . . . . .  7
     3.4.  Multiple channels  . . . . . . . . . . . . . . . . . . . .  8
   4.  MIME registration of CELT  . . . . . . . . . . . . . . . . . . 10
   5.  SDP usage of CELT  . . . . . . . . . . . . . . . . . . . . . . 12
     5.1.  Multichannel Mapping . . . . . . . . . . . . . . . . . . . 13
     5.2.  Low-Overhead Mode  . . . . . . . . . . . . . . . . . . . . 15
   6.  Congestion Control . . . . . . . . . . . . . . . . . . . . . . 16
   7.  Security Considerations  . . . . . . . . . . . . . . . . . . . 17
   8.  Acknowledgments  . . . . . . . . . . . . . . . . . . . . . . . 18
   9.  References . . . . . . . . . . . . . . . . . . . . . . . . . . 19
     9.1.  Normative References . . . . . . . . . . . . . . . . . . . 19
     9.2.  Informative References . . . . . . . . . . . . . . . . . . 19
   Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . . 20



















Valin & Maxwell         Expires November 12, 2009               [Page 2]

Internet-Draft       draft-valin-celt-rtp-profile-01            May 2009


1.  Conventions used in this document

   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
   document are to be interpreted as described in RFC 2119 [rfc2119].














































Valin & Maxwell         Expires November 12, 2009               [Page 3]

Internet-Draft       draft-valin-celt-rtp-profile-01            May 2009


2.  Overview of the CELT Codec

   CELT stands for "Constrained Energy Lapped Transform".  It applies
   some of the CELP principles, but does everything in the frequency
   domain, which removes some of the limitations of CELP.  CELT is
   suitable for both speech and music and currently features:

   o  Ultra-low algorithmic delay (as low as 2 ms)

   o  Full audio bandwidth (up to 20 kHz audio bandwidth)

   o  Support for both voice and music

   o  Stereo support

   o  Packet loss concealment

   o  Constant bitrates from under 32 kbps to 128 kbps and above

   o  Free software/open-source































Valin & Maxwell         Expires November 12, 2009               [Page 4]

Internet-Draft       draft-valin-celt-rtp-profile-01            May 2009


3.  RTP payload format for CELT

   For RTP based transportation of CELT encoded audio the standard RTP
   header [rfc3550] is followed by one or more payload data blocks.  An
   optional padding terminator may also be used.


        0                   1                   2                   3
        0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
       +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
       |                         RTP Header                            |
       +=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+
       |                   one or more frames of CELT ....             |
       +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
       |                              ....                             |
       +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

3.1.  RTP Header


        0                   1                   2                   3
        0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
       +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
       |V=2|P|X|  CC   |M|     PT      |       sequence number         |
       +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
       |                           timestamp                           |
       +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
       |           synchronization source (SSRC) identifier            |
       +=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+
       |            contributing source (CSRC) identifiers             |
       |                              ...                              |
       +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

   The RTP header is defined in the RTP specification [rfc3550].  This
   section defines how fields in the RTP header are used.

   Padding (P): 1 bit

   If the padding bit is set, the packet contains one or more additional
   padding octets at the end which are not part of the payload.  The
   last octet of the padding contains a count of how many padding octets
   should be ignored, including itself.  Padding may be needed by some
   encryption algorithms with fixed block sizes or for carrying several
   RTP packets in a lower-layer protocol data unit.

   Extension (X): 1 bit

   If the extension, X, bit is set, the fixed header MUST be followed by



Valin & Maxwell         Expires November 12, 2009               [Page 5]

Internet-Draft       draft-valin-celt-rtp-profile-01            May 2009


   exactly one header extension, with a format defined in Section 5.3.1.
   of [rfc3550].

   Marker (M): 1 bit

   The M bit MUST be set to zero in all packets.  The receiver MUST
   ignore the M bit.

   Payload Type (PT): 7 bits

   Payload Type (PT): The assignment of an RTP payload type for this
   packet format is outside the scope of this document; it is specified
   by the RTP profile under which this payload format is used, or
   signaled dynamically out-of-band (e.g., using SDP).

   Timestamp: 32 bits

   A timestamp representing the sampling time of the first sample of the
   first CELT frame in the RTP payload.  The clock frequency MUST be set
   to the sample rate of the encoded audio data and is conveyed out-of-
   band (e.g., as an SDP parameter).

3.2.  CELT payload

   For the purposes of packetizing the bit stream in RTP, it is only
   necessary to consider the sequence of bits as output by the CELT
   encoder [celt-website], and present the same sequence to the decoder.
   The payload format described here maintains this sequence.

   A typical CELT frame, encoded at a high bitrate, is approx. 128
   octets and the total size of the CELT frames SHOULD be kept below the
   path MTU to prevent fragmentation.  CELT frames MUST NOT be split
   across multiple RTP packets,

   An RTP packet MAY contain CELT frames of the same bit rate or of
   varying bit rates, since the bitrate for the frames is explicitly
   conveyed in band with the signal.  The encoding and decoding
   algorithm can change the bit rate at any frame boundary, with the bit
   rate change notification provided in-band.  No out-of-band
   notification is required for the decoder to process changes in the
   bit rate sent by the encoder.

   It is RECOMMENDED that sampling rates 32000, 44100, or 48000 Hz be
   used for most applications, unless a specific reason exists -- such
   as requirements for a very specific packetization time.  For example,
   51200 Hz sampling may be useful to obtain a 5 ms packetization time
   with 256-sample frames.  For compatibility reasons, the sender and
   receiver MUST support 48000 Hz sampling rate.



Valin & Maxwell         Expires November 12, 2009               [Page 6]

Internet-Draft       draft-valin-celt-rtp-profile-01            May 2009


   The CELT codec always produces an integer number of bytes and can
   produce any integer number of bytes, so no padding is ever required.
   Bitrate adjustment SHOULD be used instead of padding.

3.3.  Multiple CELT frames in a RTP packet

   The bitrate used by CELT is implicitly determined by the size of the
   compressed data.  When more than one frame is encoded in the same
   packet, it is not possible to determine the size of each encoded
   frame, so the information MUST be explicitly encoded.  If N frames
   are present in a packet, N compressed frame sizes need to be encoded
   at the beginning of the packet.  Each size that is less than 255
   bytes is encoded in one byte (unsigned 8-bit integer).  For sizes
   greater or equal to 255, a 0xff byte is encoded, followed by the
   size-255.  Multiple 0xff bytes are allowed if there are more than 510
   bytes transmitted.  The length is always the size of the CELT frame
   excluding the length byte itself.  The payload MUST NOT be padded,
   except in accordance with the padding bit definition in the RTP
   header.

   Below is an example of two CELT frames contained within one RTP
   packet.


       0                   1                   2                   3
       0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |V=2|P|X|  CC   |M|     PT      |       sequence number         |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                           timestamp                           |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |         synchronization source (SSRC) identifier              |
      +=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+
      |         contributing source (CSRC) identifiers                |
      |                              ...                              |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      | length frame 1| length frame 2|          CELT frame 1...      |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |         (frame 1)             |        CELT frame 2...        |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                          (frame 2)                            |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

   The following is an example of C code that interprets the length
   bytes:





Valin & Maxwell         Expires November 12, 2009               [Page 7]

Internet-Draft       draft-valin-celt-rtp-profile-01            May 2009


      int i, N, pos;
      int sizes[MAX_FRAMES][channels];
      unsigned int total_size;
      total_size=0;
      N = 0;
      pos = 0;
      while (total_size < payload_size) {
         for (i=0;i<channels;i++) {
            int s;
            int sum;
            sum = 0;
            do {
               s = payload[pos++];
               sum += s;
               total_size += s+1;
            } while (s == 255);
            sizes[N][i] = sum;
         }
         N++;
      }

3.4.  Multiple channels

   CELT supports both mono streams and stereo streams.  If more than two
   channels are desired, it is possible to use transmit multiple streams
   in the same packet.  In this case, the number of streams S and the
   pairing must be agreed with out-of-band negotiation such as SDP.
   Each stream can be either mono or stereo, depending on whether the
   channels are assumed to be correlated.  For example, a 5.1 surround
   could have the front-left and front-right channels in a stereo
   stream, the rear-left and rear-right channels in a separate stereo
   stream, while the center and low-frequency channels would be in
   separate mono streams.  In that example, the RTP packet would be:


















Valin & Maxwell         Expires November 12, 2009               [Page 8]

Internet-Draft       draft-valin-celt-rtp-profile-01            May 2009


       0                   1                   2                   3
       0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |V=2|P|X|  CC   |M|     PT      |       sequence number         |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                           timestamp                           |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |         synchronization source (SSRC) identifier              |
      +=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+
      |         contributing source (CSRC) identifiers                |
      |                              ...                              |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |  Front length |  rear length  | center length |  LFE length   |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                        Front stereo                           |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                             ...                               |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |      ...      |        Rear stereo data...                    |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                             ...                               |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                       Center mono data...                     |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                             ...                               |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                               |      LFE mono data...         |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                             ...                               |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

   In the case where streams for multiple channels are used with
   multiple frames of the same streams per packet, then all streams for
   a certain timestamp are encoded before all streams for the following
   timestamp.  In the case of the 5.1 example above with two frames per
   packet, the number of compressed length fields would be S*N = 8.














Valin & Maxwell         Expires November 12, 2009               [Page 9]

Internet-Draft       draft-valin-celt-rtp-profile-01            May 2009


4.  MIME registration of CELT

   Full definition of the MIME [rfc2045] type for CELT will be part of
   the Ogg Vorbis MIME type definition application [rfc3534].

   MIME media type name: audio

   MIME subtype: celt

   Optional parameters:

   Required parameters: to be included in the Ogg MIME specification.

   Encoding considerations:

   Security Considerations:

   See Section 6 of RFC 3047.

   Interoperability considerations: none

   Published specification:

   Applications which use this media type:

   Additional information: none

   Person & email address to contact for further information:


      Jean-Marc Valin <jean-marc.valin@octasic.com>

   Intended usage: COMMON

   Author/Change controller:

      Author: Jean-Marc Valin <jean-marc.valin@octasic.com>

      Change controller: Jean-Marc Valin <jean-marc.valin@octasic.com>

      Change controller: IETF AVT Working Group

   This transport type signifies that the content is to be interpreted
   according to this document if the contents are transmitted over RTP.
   Should this transport type appear over a lossless streaming protocol
   such as TCP, the content encapsulation should be interpreted as an
   Ogg Stream in accordance with [rfc3534], with the exception that the
   content of the Ogg Stream may be assumed to be CELT audio and CELT



Valin & Maxwell         Expires November 12, 2009              [Page 10]

Internet-Draft       draft-valin-celt-rtp-profile-01            May 2009


   audio only.


















































Valin & Maxwell         Expires November 12, 2009              [Page 11]

Internet-Draft       draft-valin-celt-rtp-profile-01            May 2009


5.  SDP usage of CELT

   When conveying information by SDP [rfc4566], the encoding name MUST
   be set to "CELT".  The sampling frequency is typically between 32000
   and 48000 Hz.  Implementations MUST support 48000 Hz and SHOULD also
   support 44100 Hz.

   The SDP parameters have the following interpretation with respect to
   CELT:

      ptime: The desired packetization time.  The sender SHOULD choose a
      number of frames per packet that corresponds to the smallest
      packetization time greater or equal to the specified ptime for the
      selected frame size.  The default is 20 ms as specified in
      [rfc3551]

      maxptime: The maximum packetization time desired.  As specified in
      [rfc4566], if the maximum is lower than the smallest packetization
      time determined from the chosen frame size (as described above),
      then that packtization time SHOULD be used despite the maxptime
      value.  The default is "no maximum".

   CELT-specific parameters can be given via the "a=fmtp:" directive.
   Several parameters can be given in a single a=fmtp line provided that
   they are separated by a semi-colon.  The following parameters are
   defined for use in this way:

      bitrate: The desired bit-rate in kbit/s for the codec only
      (excluding headers and the length bytes).  The value MUST be
      rounded to an integer number of bytes per frame.  The round-to-
      nearest method is RECOMMENDED.  The default bit-rate value is 64
      kbit/s per channel.

      frame-size: The frame size is the duration of each frame in
      samples and has to be even.  The default is 480.

      mapping: Optional string describing the multi-channel mapping.

   The selected frame-size values MUST be even.  For quality and
   complexity reasons, they SHOULD also be divisible by 8 and have a
   prime factorization which consists only of 2, 3, or 5 factors.  For
   example, powers-of-two and values such as 160, 320, 240, and 480 are
   recommended.  Implementations MUST support receiving and sending the
   default value of 480.  Implementations SHOULD also support frame
   sizes of 256 and 512 since these are the ones that lead to the lowest
   complexity.  When frame sizes that are powers-of-two are supported,
   they SHOULD be listed first in the offer and chosen over non-powers-
   of-two in the answer.



Valin & Maxwell         Expires November 12, 2009              [Page 12]

Internet-Draft       draft-valin-celt-rtp-profile-01            May 2009


   Care must be taken when setting the value of ptime: and bitrate: so
   that the RTP packet size does not exceed the path MTU.

   An example of the media representation in SDP for offering a single
   channel of CELT at 48000 samples per second might be:


      m=audio 8088 RTP/AVP 97

      a=rtpmap:97 CELT/48000/1

   Note that the RTP payload type code of 97 is defined in this media
   definition to be 'mapped' to the CELT codec at a 48 kHz sampling
   frequency using the 'a=rtpmap' line.  Any number from 96 to 127 could
   have been chosen (the allowed range for dynamic types).  If there is
   more than one channel being encoded the rtpmap MUST specify the
   channel count.  When no channel count is included, the default is one
   channel.

   The following example demonstrates the use of the a=fmtp: parameters:


      m=audio 8008 RTP/AVP 97

      a=ptime: 25

      a=rtpmap:97 CELT/44100

      a=fmtp:97 frame-size=512;bitrate=48

   This examples illustrate an offerer that wishes to receive a CELT
   stream at 44100 Hz, by packing two 512-sample frames in each packet
   (less than 25 ms) at around 48 kbps (70 bytes per frame).

5.1.  Multichannel Mapping

   When more than two channels are used, a mapping parameter MUST be
   provided.  The mapping parameter is defined as comma separated list
   of integers which specify the number of channels contained in each
   CELT stream, OPTIONALLY followed by a '/' and a comma separated list
   of channel identifiers, then OPTIONALLY another '/' and a string
   which provides an application specific elaboration on any speaker-
   feed definitions.  The channels per stream entries MUST be either 1
   or 2.  The total number of channels is indicated by the sum of the
   channels per stream entries.  The sum of the channel counts MUST be
   equal to the total number of channels.

   Channel identifiers are short alphanumeric strings.  Each identifier



Valin & Maxwell         Expires November 12, 2009              [Page 13]

Internet-Draft       draft-valin-celt-rtp-profile-01            May 2009


   MUST begin with a letter indicating the type of channel.  'A' MUST be
   used to indicate an ambisonic channel, 'S' to indicate a speaker-feed
   channel, or 'O' indicating other usage.

   A channel identifier MAY be repeated, but the meaning of such
   repetition is application specific.  Applications SHOULD attempt to
   utilize channel identifiers such that mixing all identical
   identifiers would produce a reasonable result.

   Non-surround usage such as individual performer tracks, effect send,
   "order wire", or other administrative channels may be given
   application specific identifiers which MUST not conflict with the
   identifiers defined in this draft.  These identifiers SHOULD begin
   with S if it would be sensible to include them in a mono-downmix, or
   O if it would be most sensible to exclude them from a mono-downmix.
   An example usage might be mapping=2,1,2,1,1/
   SLguitar,SRguitar,OheadsetG,SLkeyboard,SRkeyboard,OheadsetK,SMbass,Oh
   eadsetB"

   Ambisonic channels MUST follow the Furse-Malham naming and weighing
   conventions for up to third order spherical[Ambisonic].  Higher order
   ambisonic support is application defined but MUST NOT reuse any of
   WXYZRSTUVKLMNOPQ for higher order components.  For example, second
   order spherical ambisonics SHOULD use the mapping
   "mapping=1,1,1,1,1,1,1,1,1/AW,AX,AY,AZ,AR,AS,AT,AU,AV".  Any set of
   Ambisonic channels MUST contain at least one "AW" channel.

   Speaker-feed identifiers are named based on the intended speaker
   locations.  "L", "R" for the left and right speakers, respectively,
   in conventional stereo or the front left and right in 4, 5, 5.1, or
   7.1 channel surround.  "LR", "RR" for the left and right rear
   speakers in 4,5 or 5.1 channel surround.  C" is used for a center
   channel, "MLFE" for a low frequency extension channel.  "LS", "RS"
   for the side channels in 7.1 channel surround.  Additional speaker-
   feeds are application specific but should not reuse the prior
   identifiers.  For 5.1 surround in non-ambisonic form the mapping
   SHOULD be "mapping=2,2,1,1/L,R,LR,RR,C,MLFE/ITU-RBS.775-1".  When
   only one or two channels are used, the mapping parameter MAY be
   omitted, in which case the default mapping is used.  For one channel,
   the default is "mapping=1/C", while for two channels, the default is
   "mapping=2/L,R".

   For example a stereo configuration might signal:


      m=audio 8008 RTP/AVP 97





Valin & Maxwell         Expires November 12, 2009              [Page 14]

Internet-Draft       draft-valin-celt-rtp-profile-01            May 2009


      a=ptime: 5

      a=rtpmap:97 CELT/44100/2

      a=fmtp:97 frame-size=256

   Which specifies a single two-channel CELT stream according to the
   default mapping.

5.2.  Low-Overhead Mode

   A low-overhead mode is defined to make more efficient use of
   bandwidth when transmitting CELT frames.  In that mode none of the
   length values need to be transmitted.  One the a=fmtp: parameter low-
   overhead: is defined and contains a single frame size, followed by a
   '/', followed by a comma-separated list of the number of bytes per
   frame for each stream defined in the channel mapping.  The number of
   frames per channel can thus be computed as the payload size divided
   by the sum of the bytes-per-frame values.  The frame-size: parameter
   MUST not be specified and SHOULD be ignored if encountered in an SDP
   offer or answer.  The bitrate: parameter MUST also be ignored since
   the low-overhead: parameter makes it redundant.  When the low-
   overhead: parameter is specified, the length of each frame MUST NOT
   be encoded in the payload and the bit-rate MUST NOT be changed during
   the session.

   For example a low-overhead surround configuration could be signaled
   as:

      m=audio 8008 RTP/AVP 97

      a=ptime: 5

      a=rtpmap:97 CELT/48000/6

      a=fmtp:97 low-overhead=256/1/86,86,43,30;mapping=2,2,1,1/
      L,R,LR,RR,C,MLFE/ITU-RBS.775-1

   In this example, 4 bytes per packet would be saved.  This corresponds
   to a 6 kbit/s reduction in the overhead, although the 60 kbit/s
   overhead of the IP, UDP and RTP headers is still present.










Valin & Maxwell         Expires November 12, 2009              [Page 15]

Internet-Draft       draft-valin-celt-rtp-profile-01            May 2009


6.  Congestion Control

   CELT allows any bitrate, with a one byte per frame resolution,
   without any signaling requirement or overhead.  Applications SHOULD
   utilize congestion control to regulate the transmitted bitrate.  In
   some applications it may make sense to increase the packetization
   interval rather than decreasing the codec bitrate.  Congestion
   control implementations should consider the users differential
   tolerance for high latency and low quality.










































Valin & Maxwell         Expires November 12, 2009              [Page 16]

Internet-Draft       draft-valin-celt-rtp-profile-01            May 2009


7.  Security Considerations

   RTP packets using the payload format defined in this specification
   are subject to the security considerations discussed in the RTP
   specification [rfc3550], and in any applicable RTP profile.  The main
   security considerations for the RTP packet carrying the RTP payload
   format defined within this memo are confidentiality, integrity and
   source authenticity.  Confidentiality is achieved by encryption of
   the RTP payload.  Integrity of the RTP packets through suitable
   cryptographic integrity protection mechanism.  Cryptographic system
   may also allow the authentication of the source of the payload.  A
   suitable security mechanism for this RTP payload format should
   provide confidentiality, integrity protection and at least source
   authentication capable of determining if an RTP packet is from a
   member of the RTP session or not.

   Note that the appropriate mechanism to provide security to RTP and
   payloads following this memo may vary.  It is dependent on the
   application, the transport, and the signalling protocol employed.
   Therefore a single mechanism is not sufficient, although if suitable
   the usage of SRTP [rfc3711] is recommended.  Other mechanism that may
   be used are IPsec [rfc4301] and TLS [rfc5246] (RTP over TCP), but
   also other alternatives may exist.

   This RTP payload format and its media decoder do not exhibit any
   significant non-uniformity in the receiver-side computational
   complexity for packet processing, and thus are unlikely to pose a
   denial-of-service threat due to the receipt of pathological data.
   Nor does the RTP payload format contain any active content.

   Because this format supports VBR operation small amounts of
   information about the transmitted audio may be leaked by a length
   preserving cryptographic transport.  Accordingly, when CELT is used
   inside a secure transport the sender SHOULD restrict the use of VBR
   to congestion control purposes.

   CELT implementations will typically exhibit tiny content-sensitive
   encoding time variances.  Since transmission is usually triggered by
   an accurate hardware clock and the encoded data is typically
   transmitted as soon as encoding is complete this variance may result
   in a small amount of additional frame to frame jitter which could be
   measured by a third-party.  Encrypted implementations SHOULD transmit
   packets at fixed intervals to avoid the possible information leak.








Valin & Maxwell         Expires November 12, 2009              [Page 17]

Internet-Draft       draft-valin-celt-rtp-profile-01            May 2009


8.  Acknowledgments

   The authors would also like to thank the following people for their
   input: Timothy B. Terriberry, Ben Schwartz, Alexander Carot, Thorvald
   Natvig, Brian West, Steve Underwood, and Anthony Minessale.














































Valin & Maxwell         Expires November 12, 2009              [Page 18]

Internet-Draft       draft-valin-celt-rtp-profile-01            May 2009


9.  References

9.1.  Normative References

   [rfc2119]  Bradner, S., "Key words for use in RFCs to Indicate
              Requirement Levels", RFC 2119.

   [rfc3550]  Schulzrinne, H., Casner, S., Frederick, R., and V.
              Jacobson, "RTP: A Transport Protocol for real-time
              applications", RFC 3550.

   [rfc2045]  "Multipurpose Internet Mail Extensions (MIME) Part One:
              Format of Internet Message Bodies", RFC 2045,
              November 1998.

   [rfc4566]  Handley, M., Jacobson, V., and C. Perkins, "SDP: Session
              Description Protocol", RFC 4566, July 2006.

   [rfc3551]  Schulzrinne, H. and S. Casner, "RTP Profile for Audio and
              Video Conferences with Minimal Control.", RFC 3551,
              July 2003.

   [rfc3534]  Walleij, L., "The application/ogg Media Type", RFC 3534,
              May 2003.

   [rfc3711]  Baugher, M., McGrew, D., Naslund, M., Carrara, E., and K.
              Norrman, "The Secure Real-time Transport Protocol (SRTP)",
              RFC 3711, March 2004.

   [rfc4301]  Kent, S. and K. Seo, "Security Architecture for the
              Internet Protocol", RFC 4301, December 2005.

   [rfc5246]  Dierks, T. and E. Rescorla, "The Transport Layer Security
              (TLS) Protocol Version 1.2", RFC 5246, August 2008.

9.2.  Informative References

   [celt-website]
              Xiph.Org Foundation, "The CELT ultra-low delay audio
              codec", CELT website http://www.celt-codec.org/.

   [Ambisonic]
              Malham, D., "Higher order Ambisonic systems", Paper http:/
              /www.york.ac.uk/inst/mustech/3d_audio/
              higher_order_ambisonics.pdf, December 2003.






Valin & Maxwell         Expires November 12, 2009              [Page 19]

Internet-Draft       draft-valin-celt-rtp-profile-01            May 2009


Authors' Addresses

   Jean-Marc Valin
   Octasic Semiconductor
   4101, Molson Street, suite 300
   Montreal, Quebec  H1Y 3L1
   Canada

   Email: jean-marc.valin@octasic.com


   Gregory Maxwell
   Juniper Networks
   2251 Corporate Park Drive, Suite 100
   Herndon, VA  20171-1817
   USA

   Email: gmaxwell@juniper.net

































Valin & Maxwell         Expires November 12, 2009              [Page 20]